Summary of Contents for Lucas Control Systems Deeco EM-C061
- Page 1 Lucas Control Systems Deeco Systems EM-C061 14" Flat Panel Display Embedded Computer Module USER MANUAL Manual P/N: 15062 Manual Revision: 1.0 Manual Revision Date: June 1997...
- Page 3 How to contact Deeco Systems for sales or technical support: Lucas Control Systems, Deeco Systems 31047 Genstar Road Hayward, California USA 94544-7831 Phone: 1-800-376-1154 or 510-471-4700 FAX: 510-489-3500 General E-mail: sales@deeco.com Internet: http://www.deeco.com Technical Support E-mail: LDTECHSUPPORT@COMPUSERVE.COM Technical Support BBS: 510-471-5402 Baud Rate: up to 14400 Baud Data Bits:...
- Page 4 Warning!! Grounding circuit continuity is vital for safe operation of the machine. Never operate the machine with the grounding conductor disconnected. See installation instructions before connecting to the supply. The computer system contains voltages capable of producing a dangerous electrical shock. Only properly trained and authorized personnel should access the computer.
-
Page 5: Table Of Contents
1.0 OVERVIEW... 1 1.1 PRODUCT SUMMARY... 1 1.2 INDUSTRIAL COMPUTERS ... 2 1.3 SINGLE BOARD COMPUTER ... 2 1.4 ORDERING INFORMATION... 3 1.5 SPECIFICATIONS ... 5 1.6 DISPLAY... 6 2.0 INSTALLATION ... 7 2.1 UNPACKING ... 7 2.2 MOUNTING... 8 2.3 APPLYING POWER... - Page 6 A.2 EM-C061 COMPUTER REAR VIEW ... 40 A.3 EM-C061 SIDE VIEW ... 41 A.4 EM-C061 CABLING DIAGRAM ... 42 A.5 EM-C061 PANEL CUT-OUTS AND MOUNTING GUIDE ... 43 APPENDIX B: PRODUCT NAMING CONVENTION ... 45 LIMITED WARRANTY... 47 INDEX ... 49...
-
Page 7: Overview
The EM-C061 embedded computer module is an industrial Pentium®-based PC with a color TFT LCD 13.8" flat panel display. The computer can be 19 rack-mounted or easily integrated into panel cut-outs or OEM equipment. The EM-C061 is available with a resistive touch screen system that functions as a touch mouse. -
Page 8: Industrial Computers
EM-C061 in industrial control applications. Experienced Applications Engineers are available to help customers integrate computers into special situations. The EM-C061 is available with integrated 13.8" AM color TFT LCD with XGA resolution (1024 x 768) and up to 4K colors. -
Page 9: Ordering Information
Open Frame, Panel Mount Hard Drives 1.3GB, rugged 2.5" PIO4 (EIDE) 2.11GB, 3.5" Ultra SCSI (Requires PCI card slot) 3.26GB, 3.5" SCSI3 (Requires PCI card slot) 2.0GB, 2.5" rugged PIO4 (EIDE) 340MB, rugged 2.5" PIO4 (EIDE) EM-C061 Computer User Manual... - Page 10 EM-C061 Computer User Manual Floppy Drive Mounted Floppy Drive (Rear Access) PC/104 Semiconductor Disks 1010 2MB on PC/104 Card 1011 8MB on PC/104 Card Ethernet LAN Communications 10BASE-T (T-pair) / 10BASE-2 Software - Operating Systems Microsoft Windows 3.1 Microsoft Windows 95...
-
Page 11: Specifications
(@25 o C) Display > 45,000 hours* *AMTFT display backlights are considered field replaceable items and are not included in MTBF figures. EM-C061 Computer User Manual With Optional Front Panel 12.3" H x 15.2" W x 4.0" * D (312 mm x 386 mm x 102 mm) -
Page 12: Display
The display is color active matrix LCD incorporating amorphous silicon TFT. Graphics and texts can be displayed on the 1024 x 768 color panel. The TFT panel used is a low-reflection and higher- color saturation type. AMTFT technology is rapidly changing. The EM-C061 uses the latest technology in flat panel displays. -
Page 13: Installation
Components used in these systems are electrostatic sensitive. Observe proper electrostatic discharge (ESD) procedures when unpacking and handling the computer. The shipping configuration of the EM-C061 will vary according to the options ordered. The following configuration is only a general guideline: AC Power cord, +24VDC power cable, or pigtail for ±12 V, ±5V operation. -
Page 14: Mounting
EM-C061 Computer User Manual MOUNTING The EM-C061 is designed to be mounted in enclosures, rack-mounted, mounted in walls, and integrated in systems. Other arrangements can be used as long as these standard criteria are met: When the unit is safely mounted the installation must be able to support at least five times the unit’s weight. -
Page 15: Power Requirements
24 VDC Return Ground Option 704 AC Supply: Connect 100-240VAC input power to the pigtail as shown. Line Neutral Ground EM-C061 Computer User Manual Current Frequency 6.7 - 3.7 A 1.25 - 2.5 A 47-63 Hz Watts 100 W 100 W... - Page 16 EM-C061 Computer User Manual Customer Supplied ±5, ±12V: Connect ±5, ±12V and Ground to the pigtail as shown: Ground Ground +12V -12V...
-
Page 17: Single Board Computer Operation
EM-C061 Computer User Manual 3.0 Single Board Computer Operation The separate Single Board Computer (SBC) user manual contains setup, operation, and maintenance documentation for the SBC. The SBC is factory configured by Deeco Systems, and modifications are usually unnecessary. -
Page 19: Touch System
EM-C061 Computer User Manual 4.0 Touch System Refer to the manual on the Touch Driver Diskette for information on the optional touch system. Touch drivers are pre-installed at the factory and reside on the mass storage device. -
Page 21: Input/Output Interface Ports
The computer includes two serial ports, configured as COM1 and COM2. Refer to the SBC manual for configuration information. The EM-C061 includes a 12" cable with two 9-pin DSUB connectors, so customers can access the two serial ports. COM2 is disconnected from the DSUB connector on the cable and used by the touch screen when the optional touch screen is ordered. -
Page 22: Parallel Port Connector
EM-C061 Computer User Manual 5.2.2 Parallel Port Connector The parallel port uses a 25-pin IDC style DSUB. The pin out for the connector is: Name/Description -SROBE -ACK BUSY SLCT Name/Description -AUTOFD -ERROR -INIT -SLCTIN... -
Page 23: Keyboard Port
Cable length is limited to 100 m for twisted pair wires. The EM-C061 can be ordered with 10 BASE-T and 10 BASE-2 connectors. Both connectors are available when the Ethernet option is ordered. -
Page 24: Base-T Connector
EM-C061 Computer User Manual 5.4.1 10 BASE-T Connector Ethernet Network Interface RJ45 Connector Pin-Out 5.4.2 10 BASE-2 Connector The 10 BASE-2 connector is a BNC type COAX connector. 1 2 3 4 5 6 7 8 Front View Signal... -
Page 25: Data Storage
Refer to the separate SSD documentation shipped with the 2 MB or 8 MB SSD options. 6.3 FLOPPY DRIVES Refer to the separate SBC manual for information on connecting a floppy disk drive. EM-C061 Computer User Manual 6.0 Data Storage Drive Type... -
Page 27: General Maintenance
Cyclohexanone Ethyl Acetate Hexane Isopropyl Alcohol Methylene Chloride Toluene Xylene 40% NaOH Clorox Coffee Downy Fantastik Formula 409 Grape Juice Ketchup Lemon Juice Mineral Spirits Mr. Clean Mustard Spray'N'Wash Tomato Juice Top Job Turpentine Vinegar Wisk EM-C061 Computer User Manual... -
Page 29: Troubleshooting
Problem: System does not boot, or boots improperly. Sub-System to Check: Fuse Single Board Computer (Refer to the accompanying SBC manual) BIOS system (Refer to the accompanying SBC manual) Power Supply Memory Systems EM-C061 Computer User Manual... - Page 30 EM-C061 Computer User Manual Problem: Malfunctioning Display Sub-System to Check: Display Single Board Computer Motherboard (Refer to the accompanying SBC manual) Power Supply Problem: Malfunctioning Memory Systems Sub-System to Check: Single Board Computer Motherboard (Refer to the accompanying SBC manual)
-
Page 31: Power Supply
If the measured power falls within the values shown, proceed to the next troubleshooting guideline in section 9.1. Output Power: Refer to section 9.1 for procedures for testing the power supply output. EM-C061 Computer User Manual... -
Page 32: Touch Interface
EM-C061 Computer User Manual TOUCH INTERFACE ELOGRAPHICS, INC. J0 •1 2 3 4 5 6 7 8 9 10 11 0.156" (4 mm) 8.2.1 Controller Board Input Power: Check to see if the input power to the controller board meets the specifications in the following table. -
Page 33: Display
Check the SIMMs to verify that they are properly installed. Missing or incorrectly aligned SIMMs will prevent the SBC from operating. Refer to section 10.2 and the accompanying SBC manual for details on proper installation procedures. EM-C061 Computer User Manual... -
Page 35: Component Test Procedure
Option 703, @ connector J1 Option 704, @ connector J1 If the measured input voltage is not within the values shown, send the unit back to the factory for power supply replacement/repair. EM-C061 Computer User Manual Power Ground - (Return) - Page 36 EM-C061 Computer User Manual Output Power: Using a multi-meter set for DC voltage, measure the potential between ground and the pins in the following table. The voltage should match the values shown when the supply is loaded. Supplies 703, 704...
- Page 37 For protection against fire replace the fuse only with the same type and rating of fuse. Removing an Axial Power Supply Fuse With a Screwdriver (Photo used for illustrative purposes only. Models and configurations may vary.) EM-C061 Computer User Manual Description Value of F1 +24 VDC 100W A/250 VAC, Fast Blow...
-
Page 39: Component Installation And Removal
EM-C061 Computer User Manual 10.0 Component Installation and Removal Rear View... - Page 40 EM-C061 Computer User Manual Right Side View (Viewed from Front) Left Side View (Viewed from Front)
-
Page 41: Touch Controller Board
Place the computer face-down on a flat surface. Gently press the retaining clips on each end of the SIMM socket outward until the SIMM comes loose form the retaining tabs. Gently pull the SIMM module out of the socket of the motherboard. EM-C061 Computer User Manual... -
Page 42: Simms Installation
EM-C061 Computer User Manual 10.2.2 SIMMs Installation Figure A (Photo used for illustrative purposes only. Models and configurations may vary.) Insert the SIMM at an angle as shown in Figure A. The SIMM will not physically fit in the socket unless pin 1 of the SIMM matches pin 1 of the socket. -
Page 43: Microprocessor Removal And Installation
EM-C061 Computer User Manual 10.3 MICROPROCESSOR REMOVAL AND INSTALLATION Chip Removal Tool Removing the microprocessor from the socket (Photo used for illustrative purposes only. Models and configurations may vary.) Refer to the accompanying SBC User Manual for microprocessor removal and installation guidelines. -
Page 45: Appendix A: Mechanical Drawings
EM-C061 Computer User Manual Appendix A: Mechanical Drawings EM-C061 COMPUTER FRONT VIEW 11.5" (292 mm) 14.4" (366 mm) Note: Dimensions shown without optional front panel. with front panel are 12.3" H x 15.2" W (312 mm x 386 mm) Drawing not to scale -- Dimensions are in inches (mm). -
Page 46: Em-C061 Computer Rear View
EM-C061 Computer User Manual EM-C061 COMPUTER REAR VIEW SBC in Standard Model Card Slots (2 PCI, SBC, 2 ISA slots or 4 ISA slots) with Backplane Option Power Supply Touch Controller Drawing not to scale -- Dimensions are in inches (mm). -
Page 47: Em-C061 Side View
EM-C061 SIDE VIEW 2 PCI Slots 11.5" (292 mm) Drawing not to scale -- Dimensions are in inches (mm). EM-C061 Computer User Manual 2 ISA Slots Power Supply Hard Drive Floppy Drive 4.0" (102 mm) without backplane 6.2" (157 mm) -
Page 48: Em-C061 Cabling Diagram
EM-C061 Computer User Manual EM-C061 CABLING DIAGRAM Touchscreen Display Touch Controller Floppy Disk Drive FDD Option IDE HDD IDE HDD Option COM1 COM2 SCSI HDD LPT1 SCSI Controller KYBD SCSI HDD Option... -
Page 49: Em-C061 Panel Cut-Outs And Mounting Guide
EM-C061 Computer User Manual EM-C061 PANEL CUT-OUTS AND MOUNTING GUIDE 11.22" (284.99 mm) 0.09" (2.29 mm) Suggested Panel Cutout for Mounting the EM-C061 Computer without the optional front panel 8.38" (H) x 11.22" (W) (212.85 mm x 284.99 mm) 5.29" (134.37 mm) 0.32"... - Page 50 EM-C061 Computer User Manual 14.50" (368.30 mm) 0.15" 0.11" (2.80 mm) (3.81 mm) Suggested Panel Cutout for Mounting the EM-C061 Computer with the optional front panel 11.60" (H) x 14.50" (W) ( 294.64 mm x 368.30 mm) Center Line 0.15"...
-
Page 51: Appendix B: Product Naming Convention
Sealed Computer, Medium case, 10.4 display, Pentium SBC EM-C031 Embedded computer, 10.4 display, Pentium SBC *This refers to the type of CPU that the model was designed for but others CPUs may be substituted. EM-C061 Computer User Manual Processing Configuration Designator: Computers... - Page 52 EM-C061 Computer User Manual Display Nomenclature 3 f d s Sequential number ID Size of display (same as specified in base unit ID #) 8.4” Format 0 = VGA 1 = SVGA 2 = XGA 3 = SXGA Examples: 3261 = 14 (13.8 ) 1024.768 XGA display 3153 = 12 (12.1 ) 800.600 SVGA display...
-
Page 53: Limited Warranty
Any action by Buyer for any alleged breach of this warranty shall be brought to the attention of Lucas Control Systems by the Buyer within the warranty period. Repairs and/or replacement under terms of this warranty shall not extend the warranty life of the original equipment supplied. EM-C061 Computer User Manual... - Page 54 EM-C061 Computer User Manual LIMITATIONS OF LIABILITY THE BUYER AND LUCAS CONTROL SYSTEMS AGREE THAT THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY WARRANTY SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS ACCORDING TO THE TERMS DESCRIBED ABOVE. LUCAS CONTROL SYSTEMS SHALL NOT BE LIABLE FOR CONTINGENT OR CONSEQUENTIAL DAMAGES TO PERSONS OR PROPERTY, AND LUCAS CONTROL SYSTEMS’...
-
Page 55: Index
EM-C061 Computer User Manual Index 10 BASE-T Connector, 18 Applying Power, 8 BIOS, 23, 24 Diagnostics, 2 DOS, 2 Ethernet, 17 Fuse, 31 Green PC, 2 Input Power, 25, 26, 27, 29... - Page 56 EM-C061 Computer User Manual LAN, 17 LCD, 47 Mounting, 8, 35 Mouse, 2, 17 Novell, 2 OS/2, 2 Output Power, 25, 30 Parallel Port, 16 Power, 2 Power Requirements, 9 SBC, 15 SIMM, 27, 35 Specifications, 5 Touch, 26, 35...
- Page 57 EM-C061 Computer User Manual Windows, 2...
Need help?
Do you have a question about the Deeco EM-C061 and is the answer not in the manual?
Questions and answers