1. Manuals
  2. Brands
  3. Alware Manuals
  4. Toy
  5. Cyclone X8
  6. Instruction manual

Alware Cyclone X8 Instruction Manual

Octocopter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Cyclone X8 Octocopter
Instruction Manual
v1.0 (28 Jan 2014)
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cyclone X8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alware Cyclone X8

Summary of Contents for Alware Cyclone X8

  • Page 1 Cyclone X8 Octocopter Instruction Manual v1.0 (28 Jan 2014)

  • Page 2: Table Of Contents

    Contents 1. Safety Notes................................................3 2. Check List................................................4 3. Equipment Required For Assembly........................................6 4 Assembly Steps – Motor and ESC..........................................7 5.0 Assembly Steps – Arm Set...........................................8 5.1 Assembly Steps – Body and Retract System.....................................10 5.2 Assembly Steps – Final Assembly........................................11 6. Quick Collapsible Illustration..........................................16 7.

  • Page 3: Safety Notes

    1. Safety Notes Do fly only in safe areas and always away from other people! Do not operate RC aircraft within the vicinity of homes or crowds of people. RC machine are prone to accidents, failures, and crashes due to a variety of reasons including pilot error, radio interference, and lack of maintenance. Pilot are responsible for their actions and damage or injury occurring during the operation of RC aircraft machine.

  • Page 4: Check List

    Motor 4110-20 KV400 (Included in combo 4 pcs 4 pcs 2 pairs only) 8 pcs AWG Wire Red and Black (48cm ) Retract System Y-Connector Battery Strap 30cm Alware 40A OPTO ESC (Included in 4 pairs 1 pcs 2pcs combo only) 8 pcs...
  • Page 5 Main Frame Body Retract System Left Side Retract System Right Side Carbon Battery Tray 1pcs 1 pcs 1 pcs 1 pcs Landing Skid Φ16*450mm + PVC Cover H-frame Boom Φ12*450mm Carbon Arm Boom Φ22*380mm 12mm Boom Mount Set 2 sets 2 pcs 4 pcs 4 sets...

  • Page 6: Equipment Required For Assembly

    3. Equipment Required For Assembly Transmitter (7CH or above) Receiver (7Ch or above) “X” Mode OctoCopter Controller (e.g. DJI WK-M/ A2 ) 1 pcs 1 pcs 1 pcs Connectors For Batteries and Power Board 6S LiPo Battery 9000-20000mAh 22.2V (20C Min.) 6S Lipo Charger –...

  • Page 7: Assembly Steps - Motor And Esc

    8.) Solder 4 pairs AWG wires to the to 2pcs of ESCs in Parallel. Same for Power/ ESC Board which is pre- POWER/ ESC Board inside the other 3 pairs of ESCs. installed inside the Main Frame Main Frame Body of Cyclone X8. Body.

  • Page 8: Assembly Steps - Arm Set

    Assembly Steps – Arm Set...

  • Page 10: Assembly Steps - Body And Retract System

    5.1 Assembly Steps – Body and Retract System Landing Skid Φ16 + PVC Cover...

  • Page 11: Assembly Steps - Final Assembly

    5.2 Assembly Steps – Final Assembly...
  • Page 14 Fixing the Arm Boom...

  • Page 16: Quick Collapsible Illustration

    Quick Collapsible Illustration Release two Thumbscrew and fold the four arms. Tighten the Thumbscrews before flying.

  • Page 17: Gimbal Mounting Illustration

    7. Gimbal Mounting Illustration...

  • Page 18: End Of Manual

    # Report any mistakes, please email to: info@alwarerc.com Related Videos could be found on: https://www.youtube.com/watch?v=VTSlmaTg7PI End Of Manual...

Table of Contents