Smart Electrician 364-5017 Operator's Instruction Manual

Digital Multimeter 364-5017
OPERATOR'S INSTRUCTION MANUAL
! !
WARNING
READ AND UNDERSTAND THIS MANUAL BEFORE
USING THE INSTRUMENT. Failure to understand
and comply with the WARNING and operating
instructions can result in serious or fatal injuries
and/or property damage.
ITEM
Frequency
DC Amps
Accuracy (@200μA-200mA) 1.2%±5D;
DC Voltage
Accuracy (@200mV) 0.5%±1D
AC Voltage
Accuracy (45–450 Hz) 1.2%±10D
Resistance
Accuracy (@200-200K Ohm) 1.0%±2D
Sampling Rate 2.5 times/second
Overload
Protection
Operating
Temperature
Display
Battery
Weight
Features
SAVE THIS MANUAL
You will need the manual for the safety warnings
and precautions, and operating and maintenance
procedures.

SAFETY WARNINGS AND PRECAUTIONS

WARNING: When using this tool, basic safety
precautions should always be followed to
reduce the risk of personal injury and damage to
equipment.
READ ALL INSTRUCTIONS BEFORE USING THIS
METER
1. Avoid working alone. If an accident happens, an
assistant can bring help.
2. Avoid electrical shock. Use extreme caution
when using this tool near uninsulated
conductors or bus bars. Prevent body contact
with grounded surfaces such as pipes,
radiators, ranges, and cabinet enclosures when
testing voltages.
3. Avoid damaging meter. Use only as specified in
this manual.
4. Observe work areas conditions. Do not test
voltages in damp or wet locations. Don't expose
to rain.
5. Store idle equipment. When not in use, tools
must be stored in a dry location.
GAR_TL_013_0410_Smart_Electrician_Ins_Manual_364-5017_Digital_Multimeter.indd 1
DESCRIPTION
45–450 Hz
Ranges:
200μA/2000μA/20mA/200mA, 10A
(@10A) 3%±2D
Ranges:
200mV/2000mV/20/200/1000V
(@200mV-200V) 1.0%±2D
(@1000V) 1.5%±2D
Ranges: 200/750V
Ranges: 200/2000/20K/200K/2000K
Ohm
(@2000K Ohm) 1.2%±4D
Fast-acting 250mA/250V Fuse
Range: 32°–104°F
1/2" high 3-1/2" digital LCD
9V (included)
0.45 lb
32" Test Leads, Transistor (NPN
and PNP) Testing Function, Battery
Testing Function, and Automatic
Polarity and Zero Adjust
6. Dress properly. Protective, electrically
nonconductive clothes and nonskid footwear are
recommended with working.
7. Use eye protection. Always wear ANSI approved
impact safety goggles.
8. Do not overreach. Keep proper footing and
balance at all times. Do not reach over or across
electrical cables.
9. Maintain tools with care. Ensure multimeter has
a fresh battery. Inspect test leads periodically
and, if damaged, have them replaced.
10. Stay alert. Watch what you are doing, use
common sense.
11. Replacement parts and accessories. When
servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
Only use accessories intended for use with
this tool.
12. Do not operate this tool if under the influence of
alcohol or drugs.
13. We recommend that only a licensed electrician
work on high-voltage or other potentially
dangerous circuits.
NOTE: Performance of this tool may vary depending
on condition of internal battery.
! !
WARNING
The warnings, cautions, and instructions discussed
in this instruction manual can not cover all
possible conditions and situations that may
occur. It must be understood by the operator that
common sense and caution are factors which
can not be built into this product, but must be
supplied by the operator.
! !
WARNING
This product contains or produces chemicals,
including lead, known to the State of California
to cause cancer and birth defects (or other
reproductive harm). (California Health & Safety
Code 25249.5 et seq.)

OPERATION

! !
WARNING
Electrical shock can cause death or injury. Avoid
touching exposed conductors of electricity.
A AC Volt Selection Area
B Battery Test Selection Area
C DC Amp Selection Area
D 10 Amp Selection Area/Jack
E Transistor Selection Area
F Volt/Ohm/mA Jack
G COM Jack
H Diode Selection Area
I On/Off Switch
J Transistor/hFE Jack
K Ohm Selection Area
L DC Volt Selection Area
L
K
J
I
A
B
C
D
E
F
H G
4/21/10 10:44 AM