1. Manuals
  2. Brands
  3. DiSS Manuals
  4. Security System
  5. KE-8000MX
  6. Service manual

DiSS KE-8000MX Service Manual

Digital video surveillance system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Digital Video
Surveillance System
Engineering Service Manual
※
The picture might differ according to the specification and model.
※
Contents of this manual are protected under copyrights and computer program laws.
First edition
: 1 September 2007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KE-8000MX and is the answer not in the manual?

Questions and answers

Summary of Contents for DiSS KE-8000MX

  • Page 1 Digital Video Surveillance System Engineering Service Manual ※ The picture might differ according to the specification and model. ※ Contents of this manual are protected under copyrights and computer program laws. First edition : 1 September 2007...

  • Page 3: Table Of Contents

    Contents HDD INSTALLATION..............................1 HDD I ..............................1 NSTALLATION HDD F ................................2 ORMAT HDD & B (CD, DVD)....................4 ECOMMENDED ACKUP EVICE CONNECTING PERIPHERAL DEVICE & PIN ASSIGNMENT ..................5 ..........................5 ONNECTING ERIPHERAL EVICE PIN A ..............................6 SSIGNMENT NETWORK CONFIGURE ............................7 IP................................7 IXED UBLIC IP ..............................7 YNAMIC UBLIC...

  • Page 4: Hdd Installation

    1. HDD Installation HDD Installation Setting up Master/Slave jumper of HDD. Secure HDD to bracket using secure screw. Attach HDD bracket to its body using HDD bracket secure screw. Connect the data & power cable.

  • Page 5: Hdd Format

    HDD Format 1.2.1. Single HDD 1.2.1.1. In case of Lower than 500GB (EX. 500GB) Install the 500GB HDD to Primary Master. Tick on the HDD check box. (ID No. 1) Click the “FORMAT” button. 1.2.1.2. In case of Higher than 500GB (EX. 750GB) Install the lower than 500GB HDD to Primary Master (ID No.
  • Page 6 1.2.2. Multiple HDDs 1.2.2.1. In case of all HDDs are lower than 500GB (EX. 500GB) Install the all HDDs to Primary Master, Primary Slave, Secondary Master and Secondary Slave. Tick on the all HDDs check box. (ID No. 1 ~ 4) Click the “FORMAT”...

  • Page 7: Recommended Hdd & Backup Device (Cd, Dvd)

    500GB), then user can replace master HDD(lower 500GB) with slave HDD(over 500GB) to have larger HDD capacity(over 500GB) in the master position. Recommended HDD & Backup Device (CD, DVD) 1.3.1. HDD List Manufacture Capacity (GB) 7200 7200 Western Digital 7200 7200 7200 7200...

  • Page 8: Connecting Peripheral Device & Pin Assignment

    2. Connecting Peripheral Device & PIN Assignment Connecting Peripheral Device This section describes how to efficiently hook up peripheral devices with the DVR. Install the DVR on flat surface. If required, attach a rubber mount for installation. In case that 19-inch rack is used, it is recommend to install the system on shelve and use 2.5~3U(1U=1.75 inch or 4.45 cm) space for proper ventilation Note Install the system in location with good ventilation to prevent overheating.

  • Page 9: Pin Assignment

    PIN Assignment Note [ 4 Ch and 8 Ch Model ] 11 12 13 14 15 16 17 18 19 Sensor Alarm Sensor 1 Alarm 1 (+) RS 485 D+ Sensor 2 Alarm 2 (+) RS 485 D- Sensor 3 Alarm 3 (+) Sensor 4 Alarm 4 (+)

  • Page 10: Network Configure

    3. Network Configure Fixed Public IP Set the network [Type] to LAN. Enter the IP Address, provided by the Internet Company. Note Incase network cannot be connected after completing the settings, try connecting the cable to another PC. This it to check if the network (internet) connection is working properly. Dynamic Public IP 3.2.1.
  • Page 11 Set the network [Type] to DHCP. Tick on [USE DDNS] category from DDNS. Do not change the fixed setting value of the DDNS Server and the ports. If the value is changed, the network connection may not be possible. DDNS Server : cctv-link.net TCP/IP Port : 80...
  • Page 12 3.2.2. Incase xDSL modem and Router is used Note PPPoE modem can be used if Router that is compatible with the PPPoE function is used Incase Port Forwarding function of the Router had been used for connection Set the network [Type] to LAN or DHCP.
  • Page 13 Tick on [USE DDNS] category from DDNS. Do not change the values of the Dynamic IP Server and each port that are fixed. The network connection may not be possible if the inputted value is modified. DDNS Server : cctv-link.net TCP/IP Port : 80 DVR TCP &...

  • Page 14: Remotemanager Setting

    RemoteManager Setting From the RemoteManager, go to [Remote Options] and enter [DDNS IP] and [Port]. Server IP : cctv-link.net Port : 80 Incase the IP set on the DVR is Fixed IP, enter the IP, Port and Web port of the corresponding DVR while registering site on the RemoteManager.
  • Page 15 Incase the IP set on the DVR is Dynamic IP, enter the Mac Address of the corresponding DVR while registering site on the RemoteManager. ex) 001c84010021.cctv-link.net...

  • Page 16: Ir Remote Controller

    4. IR Remote Controller The function buttons of the IR Remote Controller are as below. Functions Power Button ID Selection Button Numeric Button PTZ Button Preset Button on PTZ Mode Focus Button on PTZ Mode Zoom (In & out) Button on PTZ Mode Preset Tour Button on PTZ Mode Direction Button (Left/Right/Up/Down) Enter (Selection) Button...

  • Page 17: To Reset The Admin Password

    5. To reset the Admin Password If the user forgets the Admin password, please do as below. Press the “ENTER” button until pop-up the LON-IN window. (About 5 sec.) The Admin password will be initialized to Factory Default. (Default Password : 0000) Change the admin password in the MENU\SYSTEM\USER.

  • Page 18: To Reset All The Setting Value

    6. To reset all the setting value If the DVR has frozen even system rebooting, please do as below. Press the “RETURN” button until system reboot. (About 5 sec.) After reboot, the DVR will be worked to normal. Note If you use this function, all the setting value of the DVR will return to Factory Default.

  • Page 19: Firmware Upgrade

    7. Firmware Upgrade Save the latest firmware files in ROOT directory of your USB memory stick, and connect USB memory stick to DVR’s USB port. For your reference, there are three different firmware(s) by each model – 4, 8 & 16 Ch. Turn on the DVR and login with relevant password.
  • Page 20 Select [Upgrade] Select “USB HDD/Stick” in [Method], and press [Scan]. Then, device name will be shown. Press [OK] to proceed firmware upgrade.
  • Page 21 Click [OK] to reboot DVR, after upgrade process is completed. Note The HDD have to be installed (Formatted) before Firmware. If not, the Firmware upgrade will not be worked properly.

  • Page 22: To Change Mcu

    8. To Change MCU If the DVR need to change MCU, please do as below Turn off and un-plug power cable from DVR. Open top cover of DVR. The MCU is located near the IDE cable. IDE cable You have to use dedicated tool [PLCC Extractor] to remove MCU.
  • Page 23 You have to put the Extractor into 2 slots of MCU socket as below pictures: Slots...
  • Page 24 Put the new MCU into the MCU socket. One of corner is in different shape Please note one of corner is in different shape (i.e. fool proof design). The MCU should be put in right position on the socket. Press down the MCU to make sure it is firmly attached on socket. Turn on DVR, check MCU version in [SYSTEM] >...

  • Page 25: To Change Vga Board

    9. To Change VGA Board Prepare the New VGA Board. ( Old VGA : v1.00, New VGA : v1.10) Take out the old VGA board which is installed the DVR. Please refer to the below process. Pull out the cable & screws from the VGA board.
  • Page 26 Take off the old VGA board from the DVR Install the prepared new VGA board as below process. Install the VGA board using screws. Secure the screws at rear plate.
  • Page 27 Plug-in the cable to VGA board. Note Supported VGA Monitor Resolution. 1. Old VGA board (v1.00) - 640 x 480, 800 x 600 and 1024 x 678 2. New VGA board (v1.10) - 640 x 480, 800 x 600, 1024 x 678 and 1280 x 1024 Note User has to make sure of below MCU &...

  • Page 28: Trouble Shooting

    10. Trouble Shooting 10.1 SYSTEM Problem Solution Be sure that cable is connected between monitor and DVR I cannot see anything on the monitor while There might be problem with the cable. Recommend to change the power is on. cable Be sure proper power is supplied through power cable Be sure whether the batteries are included in the IR Remote Controller otherwise change the batteries if it is too old...
  • Page 29 Be sure connection between alarm output and devices are properly connected Alarm output process doesn’t working properly Be sure alarm output in the setup menu is not configured as ‘off’ Be sure alarm output channel settings are configured properly Be sure network settings are configured properly I cannot connect the remote site.

  • Page 30: Faq

    11. FAQ Question Answer Recorded data is encrypted by SSF File format, so you cannot watch it Can I watch the recorded data outside through common movie players. Use the remote site program or DVR? exclusive viewer that supplied by ‘Backup’ function of system watching recorded data.

Table of Contents