Electrolux XBB20 User Manual page 5

2. DIMENSIONS - WEIGHT
1
A Gross weight when packaged:
B Net weight when equipped (kg)
C Package dimensions (mm) L x w x h
D Overall dimensions of machine: L x w x H (mm)
E Dimensions for fi tting beater: E x E1 x E2 (mm)
2. LOCATION
2
These are exclusively fl oor-standing beaters.
To chock or level the beater:
- Remove the foot end piece before adjusting.
- Screw with a screwdriver so that the adjustable pad makes
contact.
2.
- Check it is stable by running the beater at high speed with its
beater. Where necessary, the adjustment can be fi ne-tuned
with the machine running.
- Refi t the plug.
2. ELECTRICAL CONNECTION
3
Connection to the electrical power supply must be done according to proper professional practice by a qualifi ed and
authorised person (see current standards and legislation in the country of installation).
If an adapter is used on the socket, a check must be made that the electrical characteristics of this adapter are not lower
than those of the machine.
Do not use multiple plugs
The AC power supply to the machine must comply with the following conditions;
- Maximum voltage variation: ±5%
- Maximum frequency variation: ±1% on a continuous basis, ± 2% over short periods
ATTENTION: the electrical installation must comply (for design, creation and maintenance) with the legal and standard
requirements in the country where used.
- Check that the electric mains voltage, the value shown on the specifi cation plate and the label on the power cable are the same.
- The machine's electrical power supply must be protected against voltage surges (short-circuits and excess voltages) by
using fuses or thermal relays of the appropriate gauge relative to the place of installation and machine specifi cations – see
the specifi cations shown in column F of fi gure 2.3a
ATTENTION: Concerning protection against indirect contact (depending on the type of power supply provided and
connection of the exposed conductive parts to the equipotential protection circuit), refer to point 6.3.3 of EN 60204-1
(IEC 60204-1) with the use of protection devices for automatic shut-off of power in the event of an insulation fault with
a TN or TT, system, or for the IT system, with the use of a permanent insulation or differentials controller for automatic
shut-off. The requirements of IEC 60364-4-41, 413.1 must apply for this protection.
For example: in a TT system, a differential circuit breaker must be installed upline of the power supply, with a suitable
power cut-off (e.g.: 30 mA) on the earthing installation for the place where it is planned to install the machine.
ATTENTION: Failure to comply with these instructions means the customer runs the risk of machine failure and/or
accidents due to direct or indirect contacts.
• The electronic beaters run on a single phase power supply.
• A standardised 20A, 2 pin + earth wall socket is required.
• Check that the electric mains voltage, the value shown on
the specifi cation plate and the label on the power cable are the
same.
Note:
The machine can only be used on TN (earthing
to neutral) and TT (earthed neutral) type sup-
plies. Where a machine has to be installed on
an IT (impeding or isolated neutral) supply, there is
a solution which consists of inserting an isolating
transformer and locally putting on the machine on
TN or TT supply.
• The machine must be protected by a residual current device
(RCD) and a 16 A fuse.
XBB20/30 GB 07 07
(for information only)
2a
. Handling - Transport
- The beater is delivered fi xed to a wooden pallet.
- Use a forklift truck to remove it from the pallet, slipping the
forks beneath the feet.
If unloaded manually, take all necessary precautions to ensure
the appliance does not tip at all
To fi x the beater to the fl oor: fi x using the front feet
- Remove the end pieces from the 2 front feet.
- Use a large screwdriver to extract the adjustable feet.
2.
2a
- Mark the 2 holes to be drilled (Ø8 max. screw, min. length 80,
plugs not supplied).
ATTENTION!!
• Warning for the installer:
This electronic whisk is fi tted with a fi lter which sends any
interference from the mains to earth without going through the
variator. To work properly, the appliance earth connection must
be sound otherwise the interference may go through the variator
and damage it.
Must be earthed using the green and yellow wire.
NO EARTH = NO PROTECTION = RISK OF BREAKDOWN
2
2.
2b