Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DigiTech HARDWIRE HT-2
Summary of Contents for DigiTech HARDWIRE HT-2
- Page 1 HARDWIRE HT-2 CHROMATIC TUNER OWNER’S MANUAL...
-
Page 2: Declaration Of Conformity
Sandy, Utah 84070, USA Safety: IEC 60065 -01+Amd 1 Date: October 4, 2010 EMC: EN 55022:2006 European Contact: Your local DigiTech Sales and Service EN 55024:1998 Office or FCC Part 15 Harman Signal Processing Supplementary Information: 8760 South Sandy Parkway... - Page 3 WARNING If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. For your protection, read the following: Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you Important Safety Instructions...
- Page 4 7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.
-
Page 5: Included Items
Introduction More than a remarkable achievement, DigiTech’s HardWire series represents ® a collection of significant improvements in guitar effects pedals. The HardWire series pedals provide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peers to provide such... - Page 6 Pedal Interface 8 9 10...
- Page 7 What Does This Do? 1. Mode Button - Selects the display mode (Normal or Strobe) for the Tuning LED Array. The modes are labeled below the last two LEDs of the Tuning LED Array. 2. Input - Connect your instrument here. This jack enables battery power to the pedal when connected.
- Page 8 5. Thru Output - Connect this output to the input of your amp or the input of another pedal if you want the output signal from your instrument to be audible when the tuner is enabled. 6. Mute Output - Connect this output to the input of your amp or the input of another pedal if you want the output signal from your instrument to be muted when the tuner is enabled.
- Page 9 9. LED Indicator - Lights when the effect is turned on. When battery power is low (approximately 15 minutes before it dies), the Indicator LED begins to dim giving you advanced warning that very shortly you will need to replace the battery. 10.
- Page 10 Connecting the Tuner The HT-2 Tuner has a single 1/4" Input and two 1/4" Outputs – MUTE and THRU. The HT-2 offers true hardwire bypass when not in use to preserve your guitar’s signal without any loss or buffering into your amp and other effects. If you use the HT-2 on a pedal board with other effects devices, it doesn’t really matter where in your effects chain the HT-2 is placed as long as any effects placed before it are bypassed before you use the HT-2.
- Page 11 To connect the Tuner to your amp, do the following: 1. If you are not using battery power, connect the optional power supply to the HT-2’s power input. 2. Connect a cable from your instrument’s 1/4" jack to the 1/4” Input. 3.
- Page 12 Amplifier Setup Harman Power Supply (optional)
- Page 13 Select A Tuner Reference The HT-2 has multiple tuning references to select from: A=A 440 (standard tuning), A=A flat (tuned half step down), A=G (tuned whole step down), and alternate tuning references (A=A 437 - A=A 443). To select the tuner reference, do the following: 1.
- Page 14 Select A Display Mode The HT-2 has two different display modes – Strobe and Normal. When Strobe mode is selected, the tuning LED’s move in the direction of the input note’s tuning. If the note is flat, the LED’s move to the left indicating the note needs to be tuned up.
- Page 15 When Normal mode is selected, single or pairs of LEDs light indicating tuning status. LEDs to the left of the center blue LED light if the note is flat and needs to be tuned up. LEDs to the right of the center blue LED light if the note is sharp and needs to be tuned down.
- Page 16 Tuning Your Instrument To tune your guitar or bass in Strobe mode, do the following: 1. Press the Foot Switch to turn the tuner on. A dash appears in the note display until a note is played. 2. Play a note with your instrument. The note being played displays in the Note Display.
- Page 17 To tune your guitar or bass in Normal mode, do the following: 1. Press the Foot Switch to turn the tuner on. A dash appears in the Note Display until a note is played. 2. Play a note with your instrument. The note being played displays in the Note Display.
- Page 18 Battery Operation In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: 1.
- Page 19 into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both Release Pins are flush with the outer side of Foot Switch the pedal. Pedal Switch 9VDC Battery Foot Switch Release Pin Battery Compartment Foot Switch Spring Release Pin...
- Page 20 Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are included: • Hook-and-loop Pedalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) • Foot Switch Glow Sticker (easily visible on dark stages)
- Page 21 Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: 1. Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel off the adhesive backing from the back of the Pedalboard Pad. 3. Apply the Pedalboard Pad to the bottom of the pedal.
- Page 22 Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: 1. Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
- Page 23 Specifications Controls: Mode Button, Tuning Button, On/Off Pedal Jacks: Input, Mute, Thru Input Impedance: >1 MΩ - tuner on Input Impedance: True hardwire bypass - tuner off Power Supply: 9 V Alkaline Dry Battery or Harman power supply Current Draw: 40 mA (typical at 9 VDC) Power Consumption: 365 mW (typical w/optional power supply)
- Page 24 8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 DigiTech and HardWire ® ® registered trademarks of Harman Designed in the USA Copyright - Harman Printed in China HardWire HT -2 Owners Manual 5024337-B Please visit our website at: www.digitech.com...