Related Manuals for SA SA-15T-PW
Summary of Contents for SA SA-15T-PW
- Page 1 SA-15T-PW POWERED SPEAKERS OPERATING MANUAL SeismicAudioSpeakers.com Facebook.com/SeismicAudio Twitter.com/SeismicAudio 1-877-347-6423 Page 1...
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS Caution: To reduce the risk of electrical shock, do not remove the cover (or back). No user serviceable This symbol, wherever it appears, alerts you parts inside; refer to servicing to to the presence of uninsulated dangerous voltage inside the enclosure voltage that may qualified personnel. - Page 3 SA-15T-PW Specs: Powered 15 Inch PA Speaker Cabinets SA-15T PW (Set of 2) MODEL CONTENTS Pair of Powered 2-Way 15" PA Speaker Cabinets Mains CONDITION APPLICATION PA Speakers / Mains / PA Loudspeakers ACTIVE/PASSIVE Active / Powered WOOFER 15" Loudspeakers 50 oz Magnet and 2.5"...
- Page 4 Use this Output jack to power a Non Powered Passive speaker similar to specs of SA- 15T-PW. If you connect an 8 ohm speaker to this jack, the built in amp on the SA- 15T-PW will change to 4 ohm and double the power output.
- Page 5 Replacement Crossover for SA-15T-PW SA-15T-PW Amplifier Replacement Amplifier for SA-15T-PW Non Powered Speaker – Model: SA-15T Non Powered Version of Identical Speaker for use with the SA-15T-PW CBulb – Model: CBulb Replacement Fuse for PWS-15 and PWS-12 Crossover AmpBulb – Model: AmpBulb Replacement Fuse for PWS-15 and PWS-12 Amplifier Replacement Speaker –...
- Page 6 10 ft long XLR Splitter to single 1/8” headphone cable for use with ipods, laptops and mp3 players. MP3 / Ipod Cable – Model: SA-iE10 10 ft 1/8” to 1/8” cable for use with ipods, laptops and mp3 players. NOTE: Speaker Cabinets, Speaker Control Knobs and other internal component or parts are available by phone order only…...
-
Page 7: Connection Example
To start, take the female end of the first cable and insert it into the output jack labeled MAIN OUT LEFT on your mixing board. Then insert the male end of the cable into the XLR input of the first or left SA-15T-PW speaker. - Page 8 This example shows how to connect two SA-15T-PW speakers to a standard Mixer using one MAIN OUT jack on your mixer. By choosing this method, it will free up one main out jack on the mixing board and allow the SA-15T- PW speakers to be Daisy Chained.
- Page 9 Connecting a SA-15T-PW speaker to any headphone jack device using a 1/8” to 1/8” cable Insert a 1/8” cable into the MP3 line input on the SA-15T- PW speaker and plug the other end into any device that accepts the 1/8” headphone connection.
- Page 10 Connection Example 4 Use the Seismic Audio cable: SAXFRM-2x5 to plug your DJ Controller or any other RCA output device into the XLR inputs of the SA-15T-PW speakers. Adding Powered Sub Woofers to a SA-15T- PW speaker can be done easily by...
- Page 11 SA-15T-PW; Connect a Speakon cable into the Active Output Jack on the SA-15T-PW and insert other end to either the speakon or ¼” input on a passive speaker. After doing this, the passive speaker sound should be similar to SA-15T-PW speaker. The SA- 15T-PW amp changes from an 8 ohm load to a 4 ohm load and doubles the power output to ensure each speaker cabinet is getting the same power.
-
Page 12: Frequently Asked Questions
Why is my second SA-15T-PW speaker not working? I have one SA-15T-PW speaker connected to my mixer with a ¼” cable and I have an XLR cable connected from the SA-15T-PW speaker 1 XLR output to the XLR Input of SA-15T-PW speaker 2.