Videocon V1415N User Manual

I.Legal Notices
All rights reserved. Reproduction, transfer,
distribution or storage of part or all of the contents
in this document in any form without the prior
written permission of "VIDEOCON" is prohibited.
"VIDEOCON" operates on a policy of continuous
development. "VIDEOCON" reserves the right to
make changes and improvements to any of the
products described in this document without prior
notice. Under no circumstances shall "VIDEOCON"
be responsible for any loss of data or income or
any special, incidental, consequential or indirect
damages howsoever caused.
The contents of this document are provided
as it is. Except as required by applicable law,
V1415N
no warranties of any kind, either deselected or
implied, including, but not limited to, the implied
warranties of merchantability and fitness for a
User Manual
particular purpose, are made in relation to the
accuracy, reliability or contents of this document.
"VIDEOCON"
document or withdraw it at any time without prior
notice. The availability of particular products may
vary by region. Please check with "VIDEOCON"
Executive.
II. Software Update information
To e n h a n c e d e v i c e p e r f o r m a n c e , w e
recommend that you get in touch with the nearest
"VIDEOCON" Authorized Service Center, regarding
V. SAR
"VIDEOCON" makes no representation or warranty
that any content or service will remain available for
Your phone meets the SAR requirements for
any period of time.
exposure to radio waves, recommended by Govt.
Videocon reserves the right, in its sole
of India. Your mobile phone is a radio transmitter
discretion to change/modify/update the software
and receiver. It is designed and manufactured
(including without limitation, the availability of
so as not to exceed the limits for exposure to
any feature or content) of the phone at any time
radio-frequency (RF) energy, as recommended
without prior notice.
by the Govt. of India. These limits are part of
Content and services are transmitted by third
comprehensive guidelines and establish permitted
parties by means of networks and transmission
levels of RF energy for the general population. The
facilities over which "VIDEOCON" has no
limits include a substantial safety margin designed
control. Without limiting the generality of this
to ensure the safety of all persons, regardless of
disclaimer, "VIDEOCON" expressly disclaims
age and health.
any responsibility or liability for any interruption
The exposure standard for mobile phones
or suspension of any content or service made
employs a unit of measurement known as
available through this device.
SAR (Specific Absorption Rate). The SAR limit
"VIDEOCON" is neither responsible nor
recommended by the Govt. Of India is 1.6 Watt/kg
liable for customer service related to the content
taken over a volume containing a mass of 1 gram
and services. Any question or request for service
of issue. The highest SAR value for V1415N is
relating to the content or services should be made
0.608 W/Kg. Press *#07# to check the SAR value
directly to the respective content and service
on your phone display.
providers.
Phone Shortcuts
By default the Navigation key shortcuts are set
as below:
UP: Camera
Down: Audio player
Left: Write message
Right: FM Radio

loss. do not rub your eyes, you should rinse your
• The metal parts of the phone may irritate eyes well with fresh water and go to the
y o u r s k i n d e p e n d i n g o n y o u r h e a l t h hospital immediately.
condition. • If the leaked liquid of the battery touches the
• Do not put the phone in the back pocket. skin, it can burn the skin. Please wash your
Sitting on it may damage the phone. Do not skin with fresh water and go to the hospital
put the phone on the bottom of a bag. You immediately.
may crush it. • Never put the battery in your month. The
• When the vibrate mode is on, place the liquid of the battery can be toxic.
phone carefully to avoid it being dropped • Stop using the battery when you find it
from a height or being moved to a heat became hotter, and change color and shape
source due to the vibrating. abnormally during use, charging or storing.
• Keep the batteries dry.
• Do not use or store batteries near fire, heater
Notice for batteries use
and other place with high temperature,
otherwise it can result in leakage, over heat,
• Do not disassemble or modify your batteries,
fire or explosion. Store the battery in a cool
otherwise it can cause leakage, over heat,
and ventilated place without direct sun light.
fire or explosion.
• Do not charge the battery for more than 24
• Disposing battery in a fire can cause fire or
hours.
explosion. Old batteries should be returned
• The battery can be charged and discharged
to your dealer or be disposed according to
for hundreds of times but it will eventually
local regulations. Do not dispose the battery
wear out. The battery life is shortened with
as household waste.
each charging.
• Do not short the circuit of the battery with
• When replacing the battery, use only
wires, needles or other metal objects, or
the batteries approved by the phone
store the batteries with necklace or other
manufacturer. Damage resulting from using
metal objects, otherwise it can cause
un-authorized batteries will not be covered
leakage, over heat, fire or explosion.
by warranty.
• There is a risk of blinding if the liquid of the
batteries gets into your eyes. In case of this,
12
source; otherwise both the phone and the SIM
card may be damaged.
2.3.2.Installing and uninstalling the
SIM card and Memory Card.
The SIM card usually comes attached to a
special card. The metal contacts of SIM card
2.3.3.Unlock the SIM card
is easily damaged by scratching, so take it out
PIN code
carefully before assembling it into the phone.
Your Personal Identification Number (PIN)
code protects the SIM card against unauthorized
Switch off the phone; remove the back cover,
use. Your PIN code is usually supplied with the
battery and other external power source. Fit the
SIM card. If this security function is enabled, you
SIM card into the SIM card slot. Align the angled
need to enter the PIN code every time you turn on
corner of the SIM card with the slot. Slide in the
the phone. You can also disable this function.
SIM card, make sure it is in place, install the
battery, and restore the back cover.
To unlock the SIM card, press and hold the
power button to turn on the phone. Enter the PIN
Likewise, to remove the SIM card, switch off
code. After three consecutive incorrect PIN code
the phone, remove the battery and then take out
entries, the code is blocked, and you need the
the SIM card.
PUK code to unblock it.
PUK code
This code is required to change a locked PIN
code. If the code is not supplied with the SIM card,
contact your service provider. After ten consecutive
incorrect PUK code entries, the SIM card cannot
Insert memory card. Take compatible micro
be used any more. Please contact your service
SD card, and place it into its respective slot. provider to buy a new SIM card. You cannot edit
18
the availability of updated firmware for your device.
Please see the enclosed Service Center Directory
for the Authorized Service Center nearest to your
location.
III. Safety Precautions
Please comply with these precautions to
avoid putting yourself or other around you in a
dangerous or illegal situation, and ensure peak
performance of your device.
Icons Description
ROAD SAFETY
Do not use your device while driving.
INTERFERENCE
All wireless devices could affect your
device performance.
HOSPITALS
reserves the right to revise this
Switch off the device near hospitals
and medical equipment.
AIRCRAFT
Switch off the device in aircraft.
W i r e l e s s d e v i c e s c a n c a u s e
interference in aircraft.
REFUELLING
Switch off the device when refueling.
Do not use the device at refueling
point.

General Information
Thank you for selecting our V1415N mobile
phone. This user guide will provide you with the
general information and operation instructions.
The package includes a chargeable battery, a
charger and other accessories. Please refer to the
Accessory section for details.
Note:
Use only accessories approved by the phone
manufacturer to ensure safety. Failing to
comply with this will violate the terms and
conditions of the warranty.
If the contents and displays described in this
user guide do not match the actual operation
of the phone set, please use the display of the
actual phone set. We reserved the rights to
change the mechanisms of the phone without
notice.
This user guide is subject to change without
notice.

Traffic safety
• Do not use your phone when driving a
vehicle. Give full attention to driving and to
the road. Provided there is an emergency,
stop your vehicle in a safe place and then
use your phone. Please obey all the local
traffic laws and regulations.
• Normally the electronic systems in the
vehicle should not be affected by the
RF (Radio Frequency) signals from your
wireless phone. However if you suspect
any damage is resulting from the RF of
your phone, contact your car dealer. Stop
using your phone in the car until a qualified
technician clears the problem.
• Turn off your phone when in the gas station
or any place where using wireless equipment
is prohibited. Do not place or transport your
phone with inflammables or explosives, the
internal sparkle may cause fire.
Airplane safety
• Power off your phone before boarding, the
use of a wireless phone in an airplane will be
dangerous to the operation of the airplane
and disrupt the wireless telephone network
and maybe illegal. Failure to observe these
instructions may lead to law suit or denial of
GSM cellular network service to the offender.
• Should there be an emergency situation,
14
13
PUK code. If it is lost, Please contact your service
provider.
2.3.4.Connecting to the network
After the SIM card is unlocked, you phone will
automatically search for the registered network or
other local available network. Once connected, the
name of the network carrier will appear on the top
of the screen.
You phone is now in Standby mode, ready for
making and receiving calls.
2.4.Text Input Method
This phone provides various text input
methods that allow you to use less key strokes to
input and search for text:
• ABC/Abc input method
• Hindi input method
• Numbers 123 input
19
20
BLASTING AREAS
Switch off the device near blasting
areas.
USE SENSIBLY
Use in normal condition. Do not touch
the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or
repair phone.
BATTERIES
Use only approved batteries. Do not
connect incompatible products.
WATER-RESISTANCE
Your device is not water-resistant. Keep
it dry.
Important safety measures
Your phone is designed to comply with all
the necessary precautions and requirements and
should be treated with care. The suggested safety
measures will help you to use this product without
causing you any health hazard.
• When buying a cell phone, make sure it has
a low SAR (Specific Absorption Rate).
• U s e a w i r e l e s s h a n d s - f r e e s y s t e m
(headphone, headset) with a low power
Bluetooth emitter.
 
1.Security
Emergency call
In any country, you can dial 112 (or other
emergency call number) for emergency help.
Note:
Based on the nature of cellular networking,
the success of the emergency call cannot be
guaranteed.
For your safety
• Switch off the phone in hospitals and aircraft.
Obey any restrictions. Wireless devices
can affect the medical treatment and cause
interference in aircraft.
• Some medical devices such as hearing aids
and pacemaker may be sensitive to external
radio frequency emissions. Consult the
device manufacturers or your doctor before
using the phone around the medical devices.
• Pay special attention to the ring tone volume
and vibration settings if you have a heart
problem.
• I n a r e a s w i t h p o t e n t i a l l y e x p l o s i v e
atmosphere, such as gas stations, fuel or
chemical transfer or storage facilities, obey
all signs and instructions.
• You phone will emit radio frequency even in
the standby mode. Turn off you phone when
so instructed.
• A l w a y s o b e y a l l t h e l o c a l l a w s a n d
 
contact crew member.
2.Getting Started
2.1.Assembling the device
Gently hold the back cover of the device and
slide in upward direction to open
2.2.Batteries
The battery is included in the package. It is
not fully charged out of factory but it may still be
able to power on your phone. Please completely
use up the power of the battery and then charge
it for at least 12 hours with your phone turned off.
You battery will reach its optimal state after three
cycles of charge and discharge.
2.2.1.Installing and uninstalling the
battery
15
Phone Layout
2.5.Notification Icons
Indicator icons provide useful information
about the device, including battery level, network
signal strength, current date & time, Bluetooth
status and so forth.
Icon Description
Battery level Indicator
Network signal Strength,SIM1
Network signal Strength, SIM2
Roaming is active for SIM1
Roaming is active for SIM2
Memory card inserted
21
IV. Disclaimer
• Either keep calls short or send a SMS
instead. This advice applies especially to
Some applications accessible through your
children adolescents and pregnant women.
mobile belong to third parties and are protected
• Whenever possible, only use cell phone
by copyright, patent, trademark and/or other
when the signal quality is good
intellectual property laws. Those applications are
• People having active medical implants
provided solely for your personal noncommercial
should keep their cell phone at least 15cm
use. You may not use any application in a manner
away from the implant.
that has not been authorized by the application
• The FCC advice: "Many people mistakenly
owner or provider.
assume that using a cell phone with a lower
"Third party content and services are provided
reported SAR value necessarily decreases
"as is." "VIDEOCON" does not warrant content or
a user's exposure to RF emissions, or is
services so provided, either expressly or impliedly,
somehow "safer" than using a cell phone
for any purpose. "VIDEOCON" expressly disclaims
with a high SAR value. While SAR values
any implied warranties, including but not limited
are an important tool in judging the maximum
to, warranties of merchantability or fitness for a
possible exposure to RF energy from a
particular purpose.
particular model of cell phone, a single SAR
"VIDEOCON" does not guarantee the
value does not provide sufficient information
accuracy, validity, timeliness, legality, or
about the amount of RF exposure under
completeness of any content or service made
typical usage conditions to reliably compare
available through this device and under no
individual cell phone models."
circumstances, including negligence, shall
• World Health Organization (WHO) Advice:
"VIDEOCON" be liable, whether in contract or
Organizations such as the World Health
tort, for any direct, indirect, incidental, special or
Organization and the US Food and Drug
consequential damages, attorney fees, expenses,
Administration have stated that if people
or any other damages arising out of, or in
are concerned and want to reduce their
connection with, any information contained in, or
exposure they could use a hands-free
as a result of the use of any content or service
device to keep the phone away from the
by you or any third party, even if advised of the
head and body during phone calls, or reduce
possibility of such damages." Third party services
the amount of time spent on the phone.
may be terminated or interrupted at any time, and

regulations. Do not use your phone while and other object with magnetism. The phone'
driving. Use Hands-free operation, if s magnetism may clear the information
available, and give full attention to driving stored on floppy disk, pre-paid phone card
and to the road. Pull off the road and park and credit card.
before making or answering a call if driving • Use the phone near land phone, television,
conditions so require. radio and office automatic devices may
• If your phone is lost or stolen, notify your cause interference and affect the function of
service provider immediately to stop the SIM the mobile phone.
card from being used. • Keep the phone dry, all kinds of liquid can
• When you contact your service provider, erode the electronic circuit.
they will need your IMEI number. It is printed • K e e p t h e p h o n e a w a y f r o m e x t r e m e
on the back of your phone set (you can find temperatures.
it when you remove your battery), or call • Keep the phone away from hot places where
*#06# to look up your IMEI number. Copy the temperature may exceed 60°C, such
this number and save it for future need. as the dash board, windowsill, near fire or a
• To prevent your phone from misuse, lock lighted cigarette.
your SIM card or phone, and change • Do not paint the phone.
passwords when necessary. • Do not drop the phone or violently crush or
• Do not remove the battery without turning off shake the phone.
the phone. Failure to follow this instruction • Do not disassemble or modify your phone.
may result in data lost. This can damage the phone, cause leakage
• When you leave your vehicle, take the and break the internal circuit.
phone with you or place it in the glove • Use only damp cloth or non-static cloth
compartment to avoid theft. to clean your phone. Do not use alcohol,
• Keep the phone, battery or charger out of thinner, benzene or other chemicals or
reach of children. abrasive cleaner to clean your phone.
• The phone will become warm under normal
use and while in battery charging.
Notices for your phone use • Do not leave the phone with battery
uninstalled or with the battery empty for a
• Do not keep the phone near magnetic cards
long period of time. This may cause data
10
2.2.3.Battery level indicator
To install the battery, remove the back cover
from the phone by pressing firmly on the cover and
When the phone is on, the battery level
slide it up. Align the golden contacts of the battery
indicator is located at the upper right corner of the
to the contacts in the phone, and then gently snap
screen.
down the battery into place. Re-assemble the back
cover.
2.3.Connecting to the Network
To uninstall the battery, flip the battery out from
2.3.1.SIM card
the bottom of the battery.
Please insert available Subscriber Identity
Module (SIM) card into your phone before using it.
SIM card is supplied by your network carrier.
All the information related to network
connection is recorded on the SIM card, so are
the contact information such as names, phone
numbers and SMS that you set to store on the
SIM. You can take out the SIM card from the
phone and insert it into another GSM phone to use
it. Most new phones will recognize the SIM card
2.2.2.Using the battery
automatically.
The waiting time and calling time capacities
specified by the phone manufacturer are obtained
Do not touch the golden contacts of the
under the ideal operating environment. The
SIM card and place it away from electricity and
actual values will vary with the network condition,
magnetism to avoid damage. You will not be able
operating environment and operation method.
to use the phone if the SIM card is damaged.
Please comply with the local regulations of
Note:
disposing the battery (such as recycling). Do not
dispose it as household waste.
Before inserting and taking out the SIM card,
always make sure that the phone is switched
off and disconnected from any external power
16
add the call history to the blacklist, delete the call
Unread messages
history, you can also view the call time and call
cost.
Alarm is activated
Select any a log, Press Left Soft Key
the Option list:
General profile is active
View: View the detail of the current call.
Call: Call the current number.
Outdoor Profile is Active
Send message: Directly input the SMS and
send it to the current number.
Meeting Profile is Active
Save To Phonebook: save to phonebook.
Add To Blacklist: Add the number to black list
Silent Profile is Active
and block the same number to call you.
Earphone inserted Delete: Delete the current logs.
Bluetooth activated
 Multimedia
4.1.Camera
3.V-Connect
With this function, you can snap. Press OK
Operators functions of STK menu.
Key to snap under the view-finding window.
Enter Camera Option, Your options include:
 Switch to video recorder：Switch to video
4.Call History
interface.
With this function, you can view the information
 Image viewer : Enter in the album folder to
of Call History.
view all the photos.
Press OK Key and select Call Logs under the
 Camera Settings: Set up the camera with
standby mode if you are desired to enter in this 4 4 4 44
Anti Flicker and Delay Timer options. Set
function.
the timer status as On/Off or select the time
In the call history, you can carry out the
period.
following operations: view the call history, edit the
 I m a g e S e t t i n g s : S e t u p t h e p h o t o
call history, save the call history to phonebook,
parameters.
22

11
17
to enter
44 4 4 4 4 4 4 4 44
23