Page 1
USER GUIDE V1.0 EXTENDER How can I manage all security issues with one easy, intuitive and efficient solution? This guide describes how to install, program and operate Zipato IR Extender. Infrared...
Page 2
15 cm from other wire (antenna wires, doorbell Although Zipato has attempted to ensure the accuracy of the content of this manual, wires, wires from transformers to neon signs), steam or hot water pipes, and it is possible that this document may contain technical inaccuracies, typographical, heating ducts.
CONTENTS INTRODUCTION INTRODUCTION The ZXT-120 is a Z-Wave to IR extender for air-conditioner (AC), (Figure 1), it works with any Z-Wave compliant gateway or controller by translating Z-Wave Thermostat IR EXTENDER OPERATIONS Commands to AC IR control code. User can select the IR code from the built-in...
Page 4
Z-Wave gateway and controller does not need to have any IR control code knowledge. by routing the signal around obstacle and radio dead spots. User can use ZWave controller or gateway to select the IR code according to the ZXT-120 code list separately provided through Z-Wave configuration ZXT-120 supports Network Wide Inclusion (NWI) and Explore Frames.
• Never mix used and new batteries together. • To avoid chemical leaks, remove batteries from the ZXT-120 if you do not intend to use the remote for an extended period of time. • Dispose of used batteries properly; do not burn or bury them.
Page 6
Z-WAVE REMOTE CONTROL ZXT-120 INFORMATION 01 | Select your operation mode; please refer to “Listening Mode” section. How to get the NIF “Node Information Frame” on ZXT-120 (Inclusion) 02 | Include or Exclude the unit from the existing Z-Wave home Step...
Refer to Glossary for definition of “FLiRS” and “Always Listening” node. Important: Bit Mask Byte 4 It is not allowed to changing ZXT-120 listening mode without exclusion process (do not [Reseved] change ZXT-120 listening mode while ZXT-120 is included in a network).
QUICK INSTALLATION GUIDE How to switch ZXT-120 listening mode from “Always Listening” to IR Code Selection “FLiRS” (or vice verse) ZXT-120 is with built-in IR AC code library, user may select the IR code using Configuration Command Class. LED Indication Status Step...
• Keep away from incandescent light and direct sunlight during learning. to be learnt will locate at “5” • Make sure IR Transmitter of your original remote alight with learning diode of ZXT-120, you may also slight adjust closer or in ZXT-120). Set your original further away the distance of two devices.
• There is only one code for dry mode, user can set it at any preferred temperature. • User can still use gateway to set up scene and schedule with ZXT-120, for example, to have AC turn on at 23°C every day at 7pm, 27 °C cool...
• Before mounting, check the material and structure of the mounting location. If • Do not mount the ZXT-120 so that it sticks out from the wall edge. It could get hit by the location does not have the proper material or structure, the ZXT-120 can fall people’s bodies or objects and cause an injury.
Page 12
Note 1: When mounting the screws to the wall, leave a space When removing the ZXT-120 from the wall, lift up the ZXT-120, then pull it between the wall and screw cap as shown in the figure.
• Keep the unit dust free by wiping it with a soft, dry cloth. a wall or wooden racks. You also can place the ZXT-120 on the desk and power it with • Do not disassemble your unit, it contains no user-serviceable parts.
RF FREQUENCY IR OPERATING DISTANCE Can I use 2 or more ZXT-120 in my house? What is the max. units if yes? 868.4MHz (EU) (rm-zxt120.eu) Yes and it is very depend on the capability of gateway / controller. For example, 916.02MHz (IS) (rm-zxt120.is)
Page 15
QUICK INSTALLATION GUIDE WEIGHT SUPPORTED FUNCTION IN THERMOSTAT COMMAND CLASS 35g (Battery chassis excluded) How to get the NIF “Node Information Frame” on ZXT-120 (Inclusion) 60g (Battery chassis included) Z-Wave command class Description Supported 90g (Main + Battery chassis + AAA x3pcs)
Page 16
C O M M A N D _ C L A SS _ THERMOSTAT_ AUTO Changeover THERMOSTAT MODE = 10 MODE_SET _MODE ZXT-120 FUNCTIONS AND PARAMETERS SUMMARIES: SETPOINT TYPE = 1 HEAT mode AIR CONDITIONER Z-WAVE COMMAND Z-WAVE COMMAND FUNCTIONS...
Page 17
IR EXTENDER IR EXTENDER QUICK INSTALLATION GUIDE www.zipato.com www.zipato.com QUICK INSTALLATION GUIDE C O M M A N D _ C L A SS _ THERMOSTAT_ PARAMETER NO. = THERMOSTAT F A N _ M O D E _ FAN MODE = 0...
IR EXTENDER IR EXTENDER QUICK INSTALLATION GUIDE www.zipato.com www.zipato.com QUICK INSTALLATION GUIDE S E N S O R _ Chunlan TEMPERA- C O M M A N D _ C L A S _ MULTILEVEL_ TURE SENSOR SENSOR_MULTILEVEL Classic Comfortstar...
Page 19
IR EXTENDER IR EXTENDER QUICK INSTALLATION GUIDE www.zipato.com www.zipato.com QUICK INSTALLATION GUIDE General Lloyd General McQuay (FUJITSU) Midea Gorenje Midea_ Gree Toshiba Guangda Miller Guqiao Mirage Haier Mitsubishi Heran Hisene Mitsubishi Electric Hitachi Hualing Mitsubishi Huifeng (Heavy Industries) INYCIN Kang Li...
(collectively referred to as “ZIPATO Resellers”) with this Limited Product Warranty. ZIPATO. THEY DO NOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOU The term “ZIPATO Hardware Product” is limited to the hardware components and all HAVE AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM. IN NO its internal components including firmware.
Page 22
You are entitled to warranty service ZIPATO warrants that the products described below under normal use are free according to the terms and conditions of this document if a repair to your ZIPATO from material defects in materials and workmanship during the Limited Product branded hardware is required within the Limited Product Warranty Period.
Page 23
QUICK INSTALLATION GUIDE PRODUCT WARRANTY PERIOD TABLE PERFORMANCE OF THE LIMITED PRODUCT WARRANTY If a product defect occurs, ZIPATO’s sole obligation shall be to repair or replace PRODUCT TYPE Product Warranty Period any defective Zipato Hardware Product free of charge provided it is returned to an...
EN 62479 I hereby declare that the equipment named above has been designed to comply with NOTE: Changes or modifications not expressly approved by Zipato for compliance the relevant sections of the above referenced specifications. The unit complies with could void the user’s authority to operate the equipment. This equipment has been all applicable Essential Requirements of the Directives.
Page 25
Increase the separation between the equipment and receiver. drop it off at your Zipato re-seller store. By recycling the product and its packaging Connect the equipment into an outlet on a circuit different from that to which the in this manner you help to conserve the environment and protect human health.
Page 26
IR EXTENDER IR EXTENDER QUICK INSTALLATION GUIDE www.zipato.com www.zipato.com QUICK INSTALLATION GUIDE NOTES...
Page 27
IR EXTENDER QUICK INSTALLATION GUIDE www.zipato.com make your home smart www.zipato.com...
Need help?
Do you have a question about the ZXT-120 and is the answer not in the manual?
Questions and answers