1. Manuals
  2. Brands
  3. IDE Manuals
  4. Computer Hardware
  5. DK85R Series
  6. User manual

IDE DK85R Series User Manual

Turbo ii+ 2.5" ide solid state disk
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IDE Solid State Disk
Turbo II+ 2.5" IDE Solid State Disk
DK85R Series
081124001064
Rev. A.6
Nov. 2008

Advertisement

Table of Contents
loading

Summary of Contents for IDE DK85R Series

  • Page 1 IDE Solid State Disk Turbo II+ 2.5" IDE Solid State Disk DK85R Series 081124001064 Rev. A.6 Nov. 2008...

  • Page 2: Table Of Contents

    4.1 Installation ............................28 4.2 Partition............................28 4.3 Format............................. 30 5. Troubleshooting........................31 5.1 BIOS can not identify 2.5” IDE SSD................... 31 5.2 2.5” IDE SSD can not boot the system ..................31 6. Ordering Information.......................31 7. Contact Information.........................32 Rev. A.6 Nov. 2008...
  • Page 3 IDE Solid State Disk List of Figures Figure 1: 2.5˝ IDE SSD Overlook Diagram ................2 Figure 2: 2.5” IDE SSD Dimensions ..................3 Figure 3: 2.5˝ IDE SSD Block Diagram..................4 Figure 4: IDE Connector Pin Assignment .................7 Rev. A.6 Nov. 2008...
  • Page 4 IDE Solid State Disk List of Tables Table 1: 2.5” IDE SSD Physical Dimension (Type 1) ..............3 Table 2: IDE connector pin definitions ..................7 Table 3: ATA Command Set ......................8 Table 4: Diagnostic Codes ......................9 Table 5: Identify Device Information..................10 Table 6: Feature Supported ....................22...

  • Page 5: Product Description

    This product complies ATA standard interface and is suitable for data storage media and code storage device for embedded system and boot disk. By using 2.5˝ IDE SSD, it is possible to operate good performance for the systems, which have IDE(ATA) Interface.

  • Page 6: Specification

    IDE Solid State Disk 2. Specification 2.1 Physical Specifications 2.1.1 Overlook The overlook views of 2.5˝ IDE SSD are illustrated in Figure 1. <Front View> <Rear View> Figure 1: 2.5˝ IDE SSD Overlook Diagram Rev. A.6 2/32 Nov. 2008...

  • Page 7: Figure 2: 2.5" Ide Ssd Dimensions

    IDE Solid State Disk 2.1.2 Dimension The Dimensions of 2.5˝ IDE SSD are illustrated in Figure 2 and described in Table 1. Figure 2: 2.5” IDE SSD Dimensions Table 1: 2.5” IDE SSD Physical Dimension (Type 1) 100 ± 0.15 mm Length 69.85 ±...

  • Page 8: Electronic Specifications

    IDE Solid State Disk 2.2 Electronic Specifications 2.2.1 Product Definition 2.5˝ IDE SSD is designed to operate and work as Data or Code Storage device by NAND Flash Memory and its Controller through Standard ATA Interface to Host Systems. F L ASH...

  • Page 9: Performance Specifications

    2.5˝ IDE SSD has no seek time by being based on Flash Memory technology. 2.3.4 Mount Time The Mount Time for initializing and mounting 2.5˝ IDE SSD is different by depending on Operating System and testing Platform. 2.3.5 Data Transfer Time...

  • Page 10: Environmental Specifications

    IDE Solid State Disk 2.4 Environmental Specifications 2.4.1 Temperature Operating Temperature: 0ºC to +70ºC Non-Operating Temperature: -40ºC to +85ºC 2.4.2 Humidity Operating Humidity: 10% to 95% Non-Operating Humidity: 10% to 95% (with no condensation relative humidity) 2.4.3 Vibration Random Vibration (Non-Operation): 10~2000 Hz @ 6Grms Random Vibration (Operating): 10~500 Hz@ 3 Grms 2.4.4 Altitude...

  • Page 11: Function

    IDE Solid State Disk 3. Function 3.1 Pin Signal Assignment The signals assigned for ATA applications are described in Table 2 Table 2: IDE connector pin definitions Signal name Connector Conductor Connector Signal name contact contact RESET- Ground DD10 DD11...

  • Page 12: Support Ata Commands

    IDE Solid State Disk 3.2 Support ATA Commands ATA Command Set - ATA Command Set summarizes the ATA command set with the paragraphs that follow describing the individual commands and the task file for each. Table 3: ATA Command Set...

  • Page 13: Table 4: Diagnostic Codes

    Drive/Head register. This is because PCMCIA card interface does not allows for direct inter-drive communication (such as the ATA PDIAG and DASP signals). When the diagnostic command is issued in the True IDE Mode, the Drive bit is ignored and the diagnostic command is executed by both the Master and the Slave with the Master responding with status for both devices.

  • Page 14: Table 5: Identify Device Information

    IDE Solid State Disk (3) Identify Device – ECh Bit -> Command (7) Drive C/D/H (6) Cyl High (5) Cyl Low (4) Sec Num (3) Sec Cnt (2) Feature (1) Identify Device The Identify Device command enables the host to receive parameter information from the device. This command has the same protocol as the Read Sector(s) command.
  • Page 15 The Card must be the root storage device when a host completely replaces conventional disk storage with a device in True IDE mode. To support this requirement and provide capability for any future removable media Cards, alternate handling of Word 0 is permitted.
  • Page 16 IDE Solid State Disk ATA device and turns off Removable Media and Removable Device while preserving all Retired bits in the word. 0040h: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while zeroing all Retired bits in the word Bit 15-12: Configuration Flag If bits 15:12 are set to 8h then Word 0 shall be 848Ah.
  • Page 17 Multiword DMA mode 2 has been selected. Selection of Multiword DMA modes 3 and above are specific to device are reported in word 163 as described in Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings.
  • Page 18 Bit 1, if set to one, indicates that the device supports PIO mode 4. Support for PIO modes 5 and above are specific to device are reported in word 163 as described in Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings. Word 65: Minimum Multiword DMA transfer cycle time Word 65 of the parameter information of the Identify Device command is defined as the minimum Multiword DMA transfer cycle time.
  • Page 19 IDE Solid State Disk Bit 3 of word 82 shall be set to one; the Power Management feature set is supported. Bit 4 of word 82 shall be set to zero; the Packet Command feature set is not supported. If bit 5 of word 82 is set to one, write cache is supported.
  • Page 20 IDE Solid State Disk Download Microcode command. Bit 1 of word 86 shall be set to zero; the device does not support the Read DMA Queued and Write DMA Queued commands. If bit 2 of word 86 shall be set to one, the device supports the CFA feature set.
  • Page 21 This word describes the capabilities and current settings for CFA defined advanced timing modes using the True IDE interface. Notice! The use of True IDE PIO Modes 5 and above or of Multiword DMA Modes 3 and above impose significant restrictions on the implementation of the host as indicated in section 4.3.7: Additional Requirements for CF Advanced Timing Modes.
  • Page 22 IDE Solid State Disk Bits 8-6: Advanced True IDE PIO Mode Selected Indicates the current True IDE PIO mode selected on the card. Value Current PIO timing mode selected Specified in word 64 PIO Mode 5 PIO Mode 6 Reserved Bits 11-9: Advanced True IDE Multiword DMA Mode Selected Indicates the current True IDE Multiword DMA Mode Selected on the card.
  • Page 23 IDE Solid State Disk msec) is different from the ATA specification. (5) Idle Immediate - 95h or E1h Bit -> 95h or E1h Command (7) Drive C/D/H (6) Cyl High (5) Cyl Low (4) Sec Num (3) Sec Cnt (2)
  • Page 24 IDE Solid State Disk sector read. If an error occurs, the read terminates at the sector where the error occurred. The Command Block Registers contain the cylinder, head, and sector number of the sector where the error occurred. The amount of data transferred is indeterminate.
  • Page 25 IDE Solid State Disk (9) Read Sector(s) - 20h or 21h Bit -> 20h or 21h Command (7) Drive Head (LBA 27-24) C/D/H (6) Cylinder High (LBA 23-16) Cyl High (5) Cylinder Low (LBA 15-8) Cyl Low (4) Sector Number (LBA 7-0)

  • Page 26: Table 6: Feature Supported

    IDE Solid State Disk This command is effectively a NOP command to the device and is provided for compatibility purposes. (12) Seek - 7Xh Bit -> Command (7) Drive Head (LBA 27-24) C/D/H (6) Cylinder High (LBA 23-16) Cyl High (5)

  • Page 27: Table 7: Transfer Mode Values

    Enable Power on Reset (POR) establishment of defaults at Soft Reset. Features 01h and 81h are used to enable and clear 8 bit data transfer modes in True IDE Mode. If the 01h feature command is issued all data transfers shall occur on the low order D[7:0] data bus and the -IOIS16 signal shall not be asserted for data register accesses.
  • Page 28 IDE Solid State Disk Level Sector Count Value Minimum power consumption with Standby Reserved Reserved Device performance may increase with increasing power management levels. Device power consumption may increase with increasing power management levels. The power management levels may contain discrete bands. For example, a device may implement one power management method from 80h to A0h and a higher performance, higher power consumption method from level A1h to FEh.
  • Page 29 IDE Solid State Disk (15) Set Sleep Mode- 99h or E6h Bit -> 99h or E6h Command (7) Drive C/D/H (6) Cyl High (5) Cyl Low (4) Sec Num (3) Sec Cnt (2) Feature (1) Set Sleep Mode This command causes the device to set BSY, enter the Sleep mode, clear BSY and generate an interrupt. Recovery from sleep mode is accomplished by simply issuing another command (a reset is permitted but not required).
  • Page 30 IDE Solid State Disk (18) Write DMA – CAh Bit -> Command (7) Drive Head (LBA 27-24) C/D/H (6) Cylinder High (LBA 23-16) Cyl High (5) Cylinder Low (LBA 15-8) Cyl Low (4) Sector Number (LBA 7-0) Sec Num (3)

  • Page 31: Firmware Upgrade

    IDE Solid State Disk Multiple commands are disabled, the Write Multiple operation shall be rejected with an aborted command error. Errors encountered during Write Multiple commands are posted after the attempted writes of the block or partial block transferred. The Write command ends with the sector in error, even if it is in the middle of a block. Subsequent blocks are not transferred in the event of an error.

  • Page 32: Installation

    1. Make sure your computer is turned off before you open the case. 2. Plug the 2.5” IDE SSD carefully into the ATA slot on your computer or host adapter. 3. Connect the power cable of the 2.5” IDE SSD.
  • Page 33 IDE Solid State Disk For Windows Operating System： - To partition your new 2.5” IDE SSD, for example use Microsoft WindowsXP and WindowsXP embedded system： 1. Into your windows system. You can Click the 『Start』 『Control Panel』 『Administrative Tools』 『Computer Management』 then select 『Storage』 『Disk Manager』 to setup the partition.

  • Page 34: Format

    4.3 Format For DOS Operating System： - Before you format or partition your new 2.5” IDE SSD, you must configure your computer's BIOS so that the computer can recognize your new 2.5” IDE SSD. 1. Turn your computer on. As your computer start up, watch the screen for a message describing how to run the system setup program (sometimes called BIOS or CMOS setup).

  • Page 35: Troubleshooting

    5.1.1 Check Power Cable Status 5.1.2 Check Connector status 5.1.3 Check the Power Voltage (5V) 5.2 2.5” IDE SSD can not boot the system 5.2.1 Check BIOS setting 5.2.2 Reinstall your system Please contact your closest CSS or PQI’s office for verifying your other troubles.

  • Page 36: Contact Information

    IDE Solid State Disk 7. Contact Information CoreSolid Storage Corporation, a TDK-PQI storage business company, is represented for PQI DOM, Industry CF, and SSD products on design and business operation from Oct. 1, 2007 effectively. For further information, please contact the following CoreSolid Storage Corporation, PQI, or representative which place you are located at.

Table of Contents