Summary of Contents for Little Wonder Classen TRS-20
- Page 1 TRS-20 TURF RAKE (Serial No. 00127 & UP) TSS-20 TURF SEEDER (Serial No. 00143 & UP) OPERATORS / PARTS MANUAL Schiller-Pfeiffer, Inc. 1028 Street Road • Southampton, PA 18966 Telephone: 1-800-366-6268...
-
Page 2: Table Of Contents
The serial number sticker plate is located near the left rear corner of the TRS-20/TSS-20 frame. ORDERING PARTS When ordering parts, always give the serial number and model of your TRS-20/TSS-20 as well as the quantity, part number and description of the part needed. DIRECTIONS “Right Hand”... -
Page 3: Pre-Delivery Check List
PRE-DELIVERY CHECK LIST CHECK THE FOLLOWING BEFORE YOU DELIVER THE TRS-20/TSS-20 TO THE CUSTOMER. Guards and shields fastened in place. Decals fastened and legible. Gas lever on engine turned on. All lubrication points greased. Air cleaner. Touch up scratches. Add engine oil (refer to Engine manual) Add fuel, start engine, test run. -
Page 4: Safety Precautions
12. Stop the blades if unit has to be tilted for transportation, when crossing surfaces (i.e. sidewalks, driveways, stepping stones, etc.) or when transporting the unit to and from the area being worked on. 13. Never pick up or carry a TRS-20/TSS-20 while the engine is running. -
Page 5: Operation
Start engine. Engage bail. Move speed lever forward, to move forward. Move speed lever backwards, to reverse. Drive TRS-20/TSS-20 to area to be raked or seeder. Move height adjustment lever to the appropriate setting for the shaft assembly being used. (see “Optional Shaft Assemblies”... -
Page 6: Optional Blade Assemblies
OPTIONAL BLADE ASSEMBLIES CHANGING BLADE ASSEMBLIES Within minutes your machine can be converted to a turf rake, turf seeder or turf slicer by purchasing the optional blade assemblies available complete with side plates, bearings and drive pulley. Changing the blade assembly can be done quickly as described below. - Page 7 Seeding/Multipurpose Height The seeding/multipurpose blades are used for cutting grooves for over-seeding and can also be used for verticutting grasses. To set the height properly place unit on the lawn surface and adjust the wheel height up (see Fig. 4 ). Adjusting the wheel height up lowers the blades.
-
Page 8: General Maintenance
WITH FUEL IN TANK OR CARBURETOR OR NEAR OPEN FLAME (I.E. FURNACE, WATER HEATER, PILOT LIGHT). STORAGE INSTRUCTIONS Before the TRS-20/TSS-20 is put into storage for any period exceeding 30 days, the following steps should be taken. Drain all fuel from fuel tank and fuel lines. -
Page 9: Care For Hydraulic System
CARE FOR HYDRAULIC SYSTEM To keep the hydraulic system in working order, there are a few steps needed to take place. If synthetic oil were used we would suggest a full synthetic oil such as Mobil 1 15W50, Quaker State Full Synthetic 5W50, or a similar oil. Oil viscosity is very important to transmission life. -
Page 10: Parts Main Frame Assembly
PARTS MAIN FRAME ASSEMBLY... -
Page 11: Parts Self Propelled Assembly
PARTS SELF PROPELLED ASSEMBLY... -
Page 12: Parts Handle Assembly
PARTS HANDLE ASSEMBLY... -
Page 13: Seeder/Multipurpose Blade Assembly
SEEDER/MULTIPURPOSE BLADE ASSEMBLY QTY/PER PART NO. MACHINE DESCRIPTION 700025 Shaft w/ Blade Holders, Multipurpose 100310 Blade w/ 15/16” Holes, Multipurpose 500216 Bolt, 5/16-18 x 314 Grade 8 500217 Nut, 5/16-18 Tap Lock 600030 Shaft/Blades Sub-Assembly, Multipurpose 900026 Complete Multipurpose Shaft Assembly (Includes Shaft, Blades, End Plates, Bearings, Pulley, Key &... -
Page 14: Seed Box Assembly
TSS-20 SEED BOX ASSEMBLY QTY/PER PART NO. MACHINE DESCRIPTION 500068 1/4” NYLOC NUT 100140 GAUGE w/ BOLT & WING NUT 500089 1/4” x 1-1/2” BOLT 100142 CONTROL LEVER GRIP 100141 CABLE CONTROL LEVER 500118 1/4” x 1-3/4” BOLT 100139 CONTROL CABLE (NOT SHOWN) 100127 FRICTION WASHER 100229... -
Page 15: Seeder Tire Scrape Installation
SEEDER TIRE SCRAPE INSTALLATION SEED BOX INSTALLATION For shipping purposes only, the seed box assembly is attached to machine improperly. To set your machine correctly for operation, remove hairpin clip (A) from upper connecting rod (B). Slide upper rod out, allowing “A shaped”... -
Page 16: Safety Decals
KEY PART NO. MACHINE DESCRIPTION 100074 Decal, “Classen” 100060 Decal, “CAUTION - Muffler and Shields May Exceed 150°” 100340 Decal, “TRS-20” (Turf Rake only) 100071 Decal, “Bail Engagement” 100061 Decal, “CAUTION - Operating Instructions” SAFETY DECALS KEY PART NO. MACHINE 100341... -
Page 17: Notes
NOTES... -
Page 18: Warranty
1028 Street Road • Southampton, PA 18966 For the period of one year from the date of purchase, CLASSEN MFG., INC. will repair or replace for the original purchaser (90 days if used for rental purposes) free of charge, any part or parts found upon the examination of our factory authorized service station, or by the factory in Norfolk, Nebraska, to be defective in material or workmanship.
Need help?
Do you have a question about the Classen TRS-20 and is the answer not in the manual?
Questions and answers