Tool Shop 240-2077 Operator's Manual
  1. Manuals
  2. Brands
  3. Tool Shop Manuals
  4. Saw
  5. 240-2077
  6. Operator's manual

Tool Shop 240-2077 Operator's Manual

7-1/4" 9amp sliding compound miter saw
Hide thumbs

Advertisement

Table of Contents

240-2077
7-1/4" 9AMP SLIDING COMPOUND MITER SAW
Operator's Manual
SAVE THIS MANUAL
You will need this manual for safety instructions, operating procedures and warranty.
Put it and the original sales receipt in a safe dry place for future reference.
For questions about this product, Please call 1-866-915-8626

Advertisement

Table of Contents
loading

Related Manuals for Tool Shop 240-2077

Summary of Contents for Tool Shop 240-2077

  • Page 1 240-2077 7-1/4" 9AMP SLIDING COMPOUND MITER SAW Operator’s Manual SAVE THIS MANUAL You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in a safe dry place for future reference. For questions about this product, Please call 1-866-915-8626...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS WARNING : When using electric tools, machines or equipment, basic safety shock, and personal injury. READ INSTRUCTIONS BEFORE USING THIS TOOL 1. KEEP WORK AREA CLEAN. Cluttered areas can cause injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don’t use power tools in damp, wet, or poorly lit locations.
  • Page 3 IMPORTANT SAFETY INSTRUCTIONS 15. USE EYE PROTECTION. or coarse dust. 16. SECURE WORK. 17. DON’T OVERREACH. 18. MAINTAIN TOOLS. 19. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF posi 20. ALWAYS CHECK AND MAKE SURE TO REMOVE ANY ADJUSTING KEYS OR WRENCHES BEFORE TURNING THE TOOL ON.

  • Page 4: Specifications

    SAFETY PRECAUTIONS FOR COMPOUND MITER SAW 10. DO NOT START THE SAW WITH THE BLADE IN CONTACT WITH ANY SURFACE. cause injury. IF MAKING A CUT USING ONE HAND TO HOLD THE SAW,ENSURE THE FREE HAND IS CLEAR OF CUTTING AREA. SPECIFICATIONS Voltage: 120 volts AC, 60Hz Current rating: 9 Amps...

  • Page 5: Operating Procedures

    OPERATING PROCEDURES CAUTION! Be sure the saw is disconnected from its power source before making any repairs or performing maintenance! CLAMPING WORKPIECE: WARNING: with hold- down clamp, otherwise the tool and workpiece may be damaged. no part of the tool contacts the hold-down clamp. START UP USING YOUR SAW 2.

  • Page 6: Modes Of Use

    OPERATING PROCEDURES lower blade cally. cally. MODES OF USE Chop cut: This is a good setting for 90° crosscuts. Miter cut: miter lock knob(#11 in page 4). Move the table rotation to the left or right up to 45° left & 55° right. Quickly locate 0°, 15°, 22.5°, 30°...
  • Page 7 MAINTENANCE ALIGNING MITER AND BEVEL Aligning Miter Angle 1. Lower the head assembly and push in the lock pin to lock in the lower position. Make sure table is in 0° detent and tighten miter lock knob. Place a combination square (1) against the fence(2) and next to the blade (3) as illustrated.

  • Page 8: Replacing Saw Blade

    MAINTENANCE REPLACING SAW BLADE Arrow 1. When replacing the saw blade,make sure the new saw blade has a diameter of 7-1/4", RPM rating of at least 7,000, and arbor hole of 5/8" diameter. 2. When mounting the new saw blade, the direction arrows on the blade correspond with the arrow on the upper guard.(See Figure.5)

  • Page 9: Parts List

    PARTS LIST Please refer to the schematic drawing on page 10.

  • Page 10: Schematic Drawing

    SCHEMATIC DRAWING WARNING Repairs should be made by an authorized repair center. Do not open or disassemble this power tool . Contact at 1-866-915-8626 for questions regarding this power tool.
  • Page 11 TOOL SHOP® 7 - 1 / 4 " 9 AMP SLIDING MITER SAW WARRANTY 1-YEAR LIMITED WARRANTY: This brand power tool carries a 1-Year Limited Warranty to the TOOL SHOP® original purchaser. If the tool fails within one (1) year from the date of...

Table of Contents