Advertisement
Quick Links
Advertisement
Summary of Contents for Calandra Racing Concepts WTF1
- Page 1 Assembly Manual 1/10th Formula 1 Car...
- Page 2 Center Pivot 40194 - Hard Anodized 3254 - 2-56 Button Head 3374 - Center Pivot Socket Alum Pivot ball Bag 1 *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball around by hand, and then loosen the screws so the ball floats around very free.
- Page 3 1412 - Red Locknut 1426 - 4-40 x 13615 - 1430 - 4-40 x ½” One-Piece 5/16” Flat Head Red Low- 3281 - Flat Head 3254 - 2-56 Button Head Side Links Bag 2 Profile Ball 1566 - Rear Bottom Plate *NOTE - Before installing, inspect the side links and you will notice that the screw holes on one side of the link are larger than the holes on the...
- Page 4 Slider Pod 3440 - Motor Plate 1435 - 4-40 x 7/16” 1424 - 4-40 x 1/4” 1426 - 4-40 x 33411 - Slider Bearing Carrier Button Head Flat Head 5/16” Flat Head 3375 - Molded ½” Bag 3 3442 - Left Side Pod Plate Standoffs (4) 1574 - Graphite X-brace 3442...
-
Page 5: Top Plate
Top Plate 1434 - 4-40 x 1/4” 1384 - 2-56 Steel Ballstuds & Cups 1565 - WTF-1 Button Head for Damper tubes (4) 1407 - Anodized Hex Balls (4) Rear Top Plate Bag 4 1407 1565 1384 1384 - 2-56 Steel Ballstud 1288 - 4-40 x 5/16”... - Page 6 Damper Tubes continued... Bag 5 ** Adding the Damper Tubes to the Chassis assembly ** Snap the assembled & lubed damper tubes on the respective points as shown in the diagram to the right. You will find it easier to snap on the smaller 2-56 ball studs first, then pop the lower, larger 4-40 ballcups on.
- Page 7 Center Shock CRC Encore Shock 3290 - Bag 7 (Each assembly step below corresponds to the numbered boxes in the diagram. You may run into issues if you try building the shock out of order.) 1 - Thread the spring adjuster nut onto the shock body as shown. *This needs to be installed first or you will not be able to get it on later after the lower end of the shock is assembled!* 2 - Insert only 1 of the small o-rings into the lower end of the shock body.
-
Page 8: Front End
1547 - F1 Lower Arm Front End 1540 - Front End Plate - F1 1482 - M3 x 8mm 1490 - M3 x 8mm 1498 - M3 Locknut Ball Socket Flat Head Button Head 1543 - F1 Upper / Lower Bag F Plastic Arm Mounts 1546 - F1 Lower Arm... - Page 9 Front End - 1542 - F1 Upper Arms 1582 - E-Clip for 3221 - Steering Block Set continued... Upper Hinge Pin 1545 - F1 Upper 1496 - M4 x 30mm Hinge Pin 1544 - F1 Upper Arm / 1499 - M4 Bag F Front End Screw Steering Block Ball...
- Page 10 4720 - Axle Spacer- 1386 - 1/4” x 3/8” Differential Axle 1528 - Graphite Axle Xti-2 + 5mm 1376 - 4-40 x 3/8” Flanged Bearing w/ 4mm Stud Steel Socket Cap Bag 8 1533 - Left Clamp Hub 1533 1528 1525 - Diff Hub 4123 - Differential...
- Page 11 1436 - 4-40 x 3/8” 13783 - 4-40 x 1/8” 1378 - Body Posts 3378 - Body Posts Button Head Set Screw Bag 10 w/ collars (2 in.) w/ collars (1 in.) 1 piece of 3378 will mount to the front wing (not included) once it is installed.