Subscribe to Our Youtube Channel
Summary of Contents for Viglen BX110
- Page 1 Viglen BX110 Chassis Product Guide G r e a t M i n d s T h i n k ® C O M P U T E R S N E T W O R K S S O L U T I O N S...
- Page 2 Viglen’s Environment laboratory To gain a 'CE' mark, the Viglen computer range has had to undergo many difficult tests to ensure it is Electromagnetically Compatible. These are carried out in the in-house 'Environment lab' at Viglen Headquarters. We have made every effort to guarantee that each computer leaving our factory complies fully to the correct standards.
- Page 3 Microsoft Corporation. i386, i486, Pentium, Pentium Pro and MMX are registered trademarks of Intel Corporation. JAC-UP, Contender, Dossier, Vig, Viglen, and Envy are trademarks of Viglen Limited. Genie and Contender are registered trademarks of Viglen Limited. Copyright and Patents This manual and all accompanying software and documentation are copyrighted and all rights reserved.
-
Page 4: Important Safety Instructions
If the product has been dropped or cabinet has been damaged. f. If the product exhibits a distinct change in performance, indicating a need for service. Viglen BX110 Chassis Quick Start Guide... -
Page 5: Table Of Contents
Tools and supplies needed Gaining access to the system motherboard Removing the cover Replacing the cover Removing the Hard Disk Drive(s) Installing the Hard Disk Drive(s) Installing 5 ¼“ device(s) Replacing the Chassis fan(s) Contacting Viglen Notes Viglen BX110 Chassis Quick Start Guide... -
Page 6: Chapter 1: Chassis Overview
The removable access cover is attached to the chassis with two screws (can be secured with locking handle) and provides easy access to the S845WD1-E Motherboard and power supply Figure 1: Overview of BX110 Chassis Components Viglen BX110 Chassis Quick Start Guide... -
Page 7: Chapter 2: Controls, Connectors And Indicators
Chapter 2: Controls, connectors and Indicators Front panel Figure 2: Overview of BX110 Front Panel Viglen BX110 Chassis Quick Start Guide... -
Page 8: Control Panel Buttons
The control panel also includes a main power button and a system reset button. HDD: On the BX110 System, this light indicates IDE Hard drive activity when flashing. Chassis Back Panel The input/output connectors are accessible at the back panel of the chassis. -
Page 9: Chapter 3: Removing And Installing Components
Chapter 3: Removing and installing components This chapter provides procedures for removing and installing replaceable and/or upgradeable components in the Viglen BX110 System. Before performing the procedures, be sure to familiarise yourself with the following “Before You Begin” information. Before You Begin... -
Page 10: Tools And Supplies Needed
1. Phillips (cross-head) screwdriver (number 1 and 2 bit) 2. Flat-head screwdriver (3/16-inch) 3. Jumper removal tool or needle nosed pliers 4. Pen or pencil 5. Antistatic wrist strap and conductive foam pad (recommended) Viglen BX110 Chassis Quick Start Guide... -
Page 11: Gaining Access To The System Motherboard
Simply leaving the side panel on the system without screwing it in, as the side panel locks in place. For added security this panel can be locked by using the supplied key, to prevent unauthorized access. Viglen BX110 Chassis Quick Start Guide... -
Page 12: Removing The Hard Disk Drive(S)
Figure 3: Attaching side panel to the BX110 Chassis Removing the Hard Drive(s) Before proceeding, be sure you are thoroughly familiar with the information in “Before You Begin” at the front of this chapter. To remove a Hard Drive follow these steps: 1. -
Page 13: Installing The Hard Disk Drive(S)
2. Align and place the hard drive within the carrier in an empty slot, with the SCSI or IDE connector facing away from the chassis fan in the carrier. 3. Use a Phillips screwdriver and four screws to securely attach the disk carrier to the drive. Viglen BX110 Chassis Quick Start Guide... -
Page 14: Installing 5 ¼" Device(S)
The slide rails are attached to devices as shown below. Viglen BX110 Chassis Quick Start Guide... -
Page 15: Replacing The Chassis Fans
You Begin” at the front of this chapter. Each of the chassis fans is located in fan holder clips, one just below the power supply unit and the other behind the hard disk cage. Viglen BX110 Chassis Quick Start Guide... - Page 16 Power Supply sucks air out of the system and blows it out the rear. This is essential to maintain an optimum operating environment in the system. Viglen BX110 Chassis Quick Start Guide...
-
Page 17: Contacting Viglen
Schools: Tel: 020 8758 7027 Fax: 020 8758 7417 E-mail: schools@viglen.co.uk Corporate: Tel: 020 8758 7172 Fax: 020 8566 8930 E-mail: corporate@viglen.co.uk Public Sector: Tel: 020 8758 7079 Fax: 020 8566 8931 E-mail: public@viglen.co.uk Viglen BX110 Chassis Quick Start Guide... -
Page 18: Notes
Notes Viglen BX110 Chassis Quick Start Guide... - Page 19 Viglen BX110 Chassis Quick Start Guide...
Need help?
Do you have a question about the BX110 and is the answer not in the manual?
Questions and answers