1. Manuals
  2. Brands
  3. J&Maya Manuals
  4. Printer
  5. JMB4
  6. User manual

J&Maya JMB4 User Manual

Hide thumbs Also See for JMB4:
Table of Contents

Advertisement

Quick Links

Download this manual
JMB4 user's manual
Version: 2.4

Advertisement

Table of Contents
loading

Related Manuals for J&Maya JMB4

Summary of Contents for J&Maya JMB4

  • Page 1 JMB4 user’s manual Version: 2.4...

  • Page 2: Table Of Contents

    2.5 Power on the printer ................133 2.6 JMB4 Control panel ................144 3. Specifications ...................... 17 3.1 JMB4 general specifications ..... Error! Bookmark not defined.17 3.2 Universal Serial Bus (USB) port pin assignment ......18 3.3 Serial port pin assignment ..............19...

  • Page 3: Introduction

    C. Quick start guide D. USB cable Power Cord Quick start guide G. External carrier for media/ribbon If any parts are missing, please contact us. Save the carton and all packing materials in case you need to reship back. JMB4 user’s manual...

  • Page 4: Jmb4 Printer Features

    1.2 JMB4 Printer Features 1.2.1 Front view 1.2.2 Rear view JMB4 user’s manual...

  • Page 5: Interior View

    1.2.3 Interior view JMB4 user’s manual...

  • Page 6: Getting Started

    2.1 Loading the foil 1. Pull the release latches on both sides toward the front of printer to open the printer cover. 2. Open the foil cover by pushing the ribs (as shown in green) of foil cover. JMB4 user’s manual...
  • Page 7 3. Insert the foil roll to the supply spindle. 4. Rotate the supply hub until the notches align and lock in to the left side of supply hub. JMB4 user’s manual...
  • Page 8 5. Insert an empty media core into the take up spindle. Rotate the take up hub until the notches align and lock on the left side of take up hub. 6. Pull the foil out from the roll and stick it with adhesive tape on the empty foil take up core. JMB4 user’s manual...
  • Page 9 7. Rotate the take up hub on the left side of foil spindle until the foil is pulled tight. Note: The loading path of foil roll (outside wound) JMB4 user’s manual...

  • Page 10: Loading The Media

    2. Press the holder latch and pull the media holders open. Place the media roll on the holders and push media holder toward the roll by pressing the holder latch. Release the latch when the media is firmly on the holder. JMB4 user’s manual...
  • Page 11 3. Pull the media so it could extend out the printer. Make sure the printing surface is facing up. 4. Before pushing the media under the guides, adjust the label senor to appropriate position to detect the labels with gap, hole or black mark. JMB4 user’s manual...
  • Page 12 5. Push the media under both sides of guides. Note: The loading path of label roll (inside and outside wound) JMB4 user’s manual...

  • Page 13: Printing Up To Three Ribbons

    When printing on textile ribbons, an optional adapter is available, enabling printing on three ribbons simultaneously. 2.4 JMB4 Connecting interfaces The following interfaces could be connected to PC to operate the printer: 2.4.1 USB Slave JMB4 user’s manual...
  • Page 14 4. Turn the printer power switch to on. Caution. Please ensure that the printer power is off before connecting the interface cable. Connecting the interface cable while printer power is on might cause damage to the printer. JMB4 user’s manual...

  • Page 15: Jmb4 Control Panel

    2.6 JMB4 Control panel The key functions are available under the printer READY mode Button Appearance Function Func. Enter printer function mode Feed Feed a blank label Note: Press func. key for over 3 seconds to enter the function mode. When printer is in function mode, Func.
  • Page 16 2. Press func key for over 3 seconds to factory default Press Cancel key for over 3 seconds to enter Advanced Calibration mode: Button Appearance Function Func High Sensitive mode Cancel Quit Cancel mode Pause Normal mode Feed Low Sensitive mode JMB4 user’s manual...
  • Page 17 Flash in blue light Gap out  Cancel Flash in red light Error message Pause Flash in blue light Label out (error)  Cancel Flash in red light Error message Feed Flash in blue light Foil out (error)  JMB4 user’s manual...

  • Page 18: Specifications

    3. Specifications 3.1 JMB4 specifications Model JMB4 Resolution 203/300 dpi Print mode Direct Thermal/Thermal Transfer 32-bit CPU Memory RAM: 8MB SDRAM ROM: 4MB Flash ROM Flash ROM expandable to 8MB Print speed 200 dpi 1 to 4 ips/300 dpi 1 to 3 ips Max.
  • Page 19 2 internal expandable bitmap fonts (numeric only) Downloadable soft font 4 directions: 0, 90, 180, 270 degrees Image PCX, Direct binary graphic Options JMB4 Peeler kit JMB4 Cutter Ethernet module Expand card with battery Power Switching power adapter Input: 100 to 240V, 1.8A, 50~60Hz Output: 24V, 2.5A...

  • Page 20: Universal Serial Bus (Usb) Port Pin Assignment

    3.2 Universal Serial Bus (USB) port pin assignment Connector type: Type A and B USB A (Master) USB B (Slave) Function VBUS Note: Master VBUS provides +5V max current 500mA. Slave VBUS is N/C. For more information about USB, please visit the website: www.usb.org. JMB4 user’s manual...

  • Page 21: Serial Port Pin Assignment

    3.3 Serial port pin assignment Printer side Note: Serial port provides +5V max current 500mAh Note: Serial port is available on T4 model JMB4 user’s manual...

Table of Contents