DLS M369 Owner's Manual

DLS PERFORMANCE SPEAKERS
Welcome
Thank you for buying a DLS speaker.
Install the speakers yourself if you feel confident with our
instructions and if you have the proper tools. A poor installa-
tion job can destroy the final result even from these speakers,
so if you feel unsure, turn over the installation job to someone
better suited to it.
Three-way coaxial system
These speakers have a very good sound but as always it is
important to do a correct installation.
Installation
Speaker drivers:
This kind of speakers are usually mounted in the car's par-
cel shelf. In some older car's it may also be possible to install
them in the door. We recommend you to install the drivers in
a strong baffle of MDF-board or similar, this will improve the
sound very much. It is important to fasten the speakers pro-
perly in order to avoid bad sound or rattling.
They must be fastened securely to prevent danger to oc-
cupants in a collision or sudden braking.
Filter boxes:
We use separate crossovers (filters) with high class com-
ponents to these speakers in order to get the best possible
sound. Attach the filter boxes are properly to the interior of
the vehicle to avoid rattling. Don't place them close to the in-
ternal wiring of the car, this can cause interference. Install the
filter boxes in a dry place. Fasten them with wire ties. Connect
them as in the drawing in this manual.
The filters must be used, if you connect without them the
sound becomes bad and you will destroy the tweeter.
Wiring:
Use high quality speaker cables. Make sure the cables don't
get jammed causing a short circuit to ground. This can dama-
ge the output circuits of your head unit or amplifier.
Break-in period
Allow the speakers to play at normal volume for at least 15-20
hours. After this time the performance will be correct.

Warranty service

This speaker is covered by warranty, depending on the condi-
tions in the country where it is sold. If the speaker is returned
for service, please include the original dated receipt (or a copy)
with the product.
SE-40251 Göteborg, Sweden

OWNERS MANUAL

DLS Svenska AB
P.O. Box 13029
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
Connection of speakers
Make sure you connect the cables with correct polarity to the
speakers. Observe the markings on the terminals.
Black cable to
small terminal
Tweeter / mid -
Red cable
Tweeter +
Yellow cable
Midrange +
Blue cable: +
Black cable: -
Technical data:
Article number
Art.number crossover
Bass driver
Midrange driver
Tweeter
Impedance
Nom. RMS power
Max / Peak- power
Frequency range
Magnet size
Mounting hole
Mounting depth
Speaker phasing
To be sure to have the correct speaker polarity (phase) you
can check this by using a 1,5 Volt battery.
Connect a cable from the battery plus-pole to the speaker
plus, and a cable from the battery minus to the speaker
minus.
When the speakers are correctly connected the speaker
cone should move in the same direction on both right and left
channel.This check must be made on the cables going from
the speakers, to the output terminals of your car stereo or
amplifier.
Technical Assistance
For technical assistance ask the shop where the product was
sold or the distributor in your country.
You can also send an e-mail to info@dls.se
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
M369
6x9"
3-way coaxial
Signal out
to speaker
Croccover
M369
Signal in
M 369
10-22369
9-22369F
6 x 9" / 236 x 165 mm
2" / 45 mm
20 mm
4 ohm
80 Watt
120 / 200 Watt
50Hz - 20 kHz
100 mm / 3,15"
221 x 155 mm (4,84")
86 mm ( 3,37")
Blue cable
to big termi-
nal + (Bass)
Black cable
to small
terminal -
(Bass)