Advertisement
CONSUMPTION DATA
Temperature
Programme
Selector
(°C)
Cotton
90
Cotton
60
Mixed Cotton /
60
Synthetics
Synthetics
40
30 min / 30° C
30
Delicates
40
Wool
40
Silk
30
Prewash cycle increases programme duration by approx. 15 minutes. Consumption values were measured in
normalized conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
ADDING DETERGENT AND ADDITIVES
Add the detergent and the additives into the dispenser as follows:
•
Programmes with pre- and main wash
•
Main wash programme without prewash
•
Fabric softeners and conditioners
•
Chlorine bleach
•
Stain remover agents
•
Anti-scale agents (water hardness 4)
Important:
•
Be careful not to fill more than the "MAX" level mark.
•
For programmes with prewash: do not use liquid detergents.
•
For programmes without prewash from cold to 40° C it is
recommended to use a liquid detergent to avoid whitish
residues on the coloured laundry.
CLOSE THE DOOR AND SELECT THE PROGRAMME
1.
Turn the programme selector knob clockwise to the desired programme.
2.
The remaining time indication lights up and the Start button "
3.
Turn the temperature knob to the required temperature.
4.
Turn the spin speed selector to the required setting.
PRESS ANY DESIRED OPTION BUTTON(S).
Intensive Rinse button "
"
•
For improved rinsing efficiency the rinse water level and the cycle time are increased.
•
This option is particularly suitables for areas with very soft water washing baby linen and helps
people with allergies.
Rinse Hold button "
"
•
The laundry remains in the last rinse water without progressing to the spin cycle to avoid creasing
and prevent colours from changing.
•
This option is particularly recommended for the programmes Synthetics "
•
This function is particularly useful if you want to postpone spinning to a later time or when you do
not wish to spin the clothes.
Note: The programme is stopped in "Rinse Hold" at the time the Rinse Hold button "
Terminate the "Rinse Hold" option:
•
Press the Rinse Hold button "
" again; the programme will terminate automatically with the spin
cycle to the present wash programme.
•
If you do not wish to spin the clothes, turn the programme knob to the drain programme "
push the Start button "
".
Load
Water
Energy
Programme
Duration
(kg)
(l)
(kWh)
(min)
5.0
49
1.60
120
5.0
45
1.15
120
2.0
54
0.70
120
2.0
50
0.50
80
3.0
35
0.40
30
1.5
50
0.50
45
1.0
50
0.50
45
1.0
35
0.40
30
" is flashing.
The pilot lamp lights up.
" or Delicates "
" flashes.
Prewash button "
"
•
Only for heavily soiled loads (for example sand, granular dirt) sensible
•
The cycle time increases from 5 to 15 min.
Start Delay button "
"
•
Select the programme and the option (if necessary). The remaining time indication lights up;
•
Press the Start Delay button "
•
Press the Start button "
". The Start Delay light flashes until the programme starts.
•
The number of hours preselected can later be reduced pressing again the Start Delay button "
To cancel the "Start Delay" option.
•
Turn the programme selector to the "
PROGRAMME START
Open the tap and press the Start button "
DOOR LOCK
During the running programmes the door can be opened for adding further laundry.
The door locks automatically in all spinning cycles. If the programme is stopped or the electrical power
supply is terminated, the door lock will open after approximately 1 minute.
Note:If you open the door during the programme, the Start button "
continue the cycle.
PROGRAMME END
•
The rest time display is on "End".
1.
Turn the programme selector to the "
2.
Turn the water supply tap off.
3.
Open the door and the drum flaps and unload the machine.
SELECTING A NEW PROGRAMME, SPIN SPEED, OPTIONS AFTER PROGRAMME START
1.
Press the Start button "
" to pause the programme. The light flashes.
2.
Select the new programme, temperature, spin speed and options.
3.
Press the Start button "
" to start the programme again.
TO STOP, RESET A PROGRAMME BEFORE THE END
1.
Press the Start button "
" to pause the programme. The light flashes.
2.
Set the programme selector to Drain "
3.
Press the Start button "
" to start the drain programme.
The door is unlocked as soon as the rest time display is on "End".
AUTOMATIC SAFETY FUNCTIONS / FAULTS
This washing machine is equipped with automatic safety functions which detect and diagnose faults at
an early stage and react appropriately. Often, however, the faults detected are small enough to be
solved in a matter of minutes. For example:
•
The washing machine will not start.
•
The additive products are not being fully washed out of the detergent dispenser.
•
The washing machine is unstable during the spin cycle.
•
The washing machine does not spin at the end of the programme.
Information about the above problem can be found in the Troubleshooting Guide.
What should I do when the automatic safety detects a malfunction?
The programme is interrupted and the fault is indicated as follows:
".
Indicators flashing
Remaining time indication and water tap
Remaining time indication
" and
" to select the delay time by 2, 4, 6, 8 hours;
" position.
". The pilot lamp lights up.
" is flashing. Press it again
" position.
".
Solution
See "No or insufficient water supply".
Other faults (see "Troubleshooting Guide")
5019 100 12582
GB
".
Advertisement
