Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for King Technology Pool Frog
- Page 1 YCLER INERAL URIFIER OOLS Instruction Manual...
-
Page 2: Table Of Contents
Replacing Control Dial O’Rings Replacing Cap O’Ring and Knob Winterizing Above Ground Filter Installation Above Ground Base Installation Inground Installation Off-line Installation 17 &18 Special Inground Installations Warranty Back For information on King Technology’s entire product line, visit our website at www.kingtechnology.com... -
Page 3: Pool Frog
POOL Welcome to easier pool care courtesy of POOL FROG ® . With POOL FROG ® your pool water will look and feel better without a lot of work or a lot of chemicals. This system eliminates bacteria and prevents algae growth FROG ®... -
Page 4: Ensuring A Healthy Swimming Pool
• Make sure the pool has • Before beginning with any Total Dissolved Solids: <2000 adequate circulation. The pool care program, pool water must completely including POOL FROG ® , you Stabilizer: 20 –50 ppm circulate through the pump must first balance your pool and filter at least 1 to 2 times water. -
Page 5: Start-Up And Operation
® . Follow USE CHLORINE SHOCK ONLY. chlorine burn off. Follow manufacturer's directions carefully. manufacturer’s directions carefully. • Install a POOL FROG ® Mineral Reservoir into the Cycler. (Follow Directions on Page 7.) • Insert FROG ® • When chlorine REMEMBER TO •... -
Page 6: Another Means Of Chlorine Support
Start Up ...continued from page 5 • For the first • After each testing, adjust the week test dial up by 1/2 increment if the the pool free chlorine reading has water daily Pool dropped below .5 ppm or for free adjust down by 1/2 increment chlorine to Test... -
Page 7: Replacing A Reservoir, Frog
Reservoir itself to make Control sure you have the correct Pac. POOL FROG ® Reservoir to fit your POOL FROG ® Cycler. * RESERVOIRS MUST BE REPLACED EVERY SEASON. CAUTION read carefully - • USE ONLY the factory recommended replacement Reservoir, FROG ®... - Page 8 Using FROG for a No-Algae Guarantee ® • One FROG ® for up to 15,000 gallons. ® • Two FROG for up to 30,000 gallons. If you are not using FROG ® , proceed to Step 18. Insert upside down into center of Mineral Remove cap from Reservoir pushing...
- Page 9 Reservoir until secure. • DO NOT USE CAP TOOL TO TIGHTEN CAP. Use for removal only. • For easy reminders, place a POOL FROG ® reminder sticker on your calendar to mark the six month replacement of the Reservoir and approximate replacement times for the Bac Pac.
-
Page 10: Troubleshooting
Trouble Shooting Problem Remedy What do I do 1. Make sure your filtration 3. Make sure total alkalinity 5. Make sure pool has a system is working properly is within 60-120. Adjust with free chlorine reading of if the water (i.e. -
Page 11: Parts List
Parts List 8 & 9 OTHER COPY? SILICONE LUBRICANT COPY COPY OTHER COPY? SILICONE COPY LUBRICANT COPY COPY COPY CYCLER DIAGRAM/PARTS LIST • 5100/5200 SERIES CYCLER DIAGRAM/PARTS LIST • 5400/5600 SERIES REF. # PART NUMBER DESCRIPTION QTY. REQ. REF. # PART NUMBER DESCRIPTION QTY. -
Page 12: Replacing Control Dial O'rings
Cycler Maintenance Replacing the Control Dial O'Rings for Above Ground Cyclers 5100/5200 Series Locking Pin (Back of Cycler) OTHER COPY? SILICONE LUBRICANT COPY COPY COPY Control 4. Replace both o'rings. Dial PORT Please note: the back o'ring (Front of has a loose fit in the groove. Cycler) Upon replacement squeeze a little silicone lubricant that... -
Page 13: Replacing Cap O'ring And Knob
Replacing Cap O'Ring OTHER COPY? SILICONE LU BRICANT COPY COPY COPY 1. Hold cap in front of you 2. Take hold of the far end of as you stretch the o'ring into 3. Lubricate o'ring often with upside down with the o'ring the o'ring with the thumb and the remainder of the cap silicone lubricant that came... -
Page 14: Above Ground Filter Installation
Above Ground Filter Installation - Models 5100/5200 TOOLS NEEDED Screwdriver Wrench Screw one end of nipple INCLUDED WITH CYCLER into the filter return. -Nipple Kit Apply teflon tape to each Screw the left port of threaded end of nipple. Cycler on to open nipple Tighten turning 1 to 2 revolutions with end until upright and... -
Page 15: Above Ground Base Installation
Above Ground, Base Installation – Models 5100/5200 TOOLS NEEDED Screwdriver PUMP FILTER The Cycler should always be installed Wrench between the filter and pool (or between heater and pool if applicable). TO POOL MATERIALS NEEDED: Teflon Tape Two Hose Adapters 1 1/2"... -
Page 16: Inground Installation
Inground Installation – Models 5400/5600 TOOLS NEEDED COPPER PIPE Wrench Removal Maximum Do NOT install in copper pipe if using Bac Pac as chemical corrosion occurs. Install after all equipment and as far as possible from heater. Hacksaw 12" to 15" Leave 12"... -
Page 17: Off-Line Installation 17 &18
Off-line Installation – Models 5430/5630 TOOLS NEEDED Install off-line when insufficient room Wrench for an in-line application. Install as far from heater as possible. Screwdriver Battery Operated Drill with 5/8" or 19/32" Bit Do NOT install an off-line Can be installed with the water flow in either Cycler in-line as this Cycler direction due to its bi-flow valve. - Page 18 When pipe is Cut tubing totally dry, drill two 19/32" or to size for 5/8" holes each Cycler C Y C LE M e te re d Po ol Purifier 4 0 0 C Y C LE S ER IES connection 2"...
-
Page 19: Special Inground Installations
Special Inground Installations If using POOL FROG with A. With High GPMS ® CYCLER the chlorine Bac Pac, Install T-fittings exactly as POOL special installations shown. CHECK should be considered VALVE when: 1. Water flow is higher than SUCTION FROM 80 gpm. - Page 20 King Technology within 30 days of purchase warranty lasts, so the above limitation may not apply to and installation.
Need help?
Do you have a question about the Pool Frog and is the answer not in the manual?
Questions and answers