1. Manuals
  2. Brands
  3. Micron Manuals
  4. Server
  5. NetFRAME 2100 Series
  6. Product manual

Micron NetFRAME 2100 Series Product Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NetFRAME 2100 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Micron NetFRAME 2100 Series

Summary of Contents for Micron NetFRAME 2100 Series

  • Page 2 Micron products are not designed, intended or authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of the Micron product could create a situation where personal injury or death may occur.

  • Page 3: Table Of Contents

    For information regarding Refunds and Drive Cabling Considerations..... 24 Returns..........10 IDE Requirements ....... 25 How To Contact Micron Electronics, Inc. . 10 SCSI Requirements......25 2. Chassis Description ......11 Installing a 5.25-inch Peripheral Device25 Removing a 5.25-inch Peripheral Device Chassis Feature Summary ......
  • Page 4 Processor ...........41 If You Cannot Access Setup....63 Memory ..........41 Starting Setup ........64 Peripherals..........43 Setup Menus ........64 Super I/O Chip ........43 Main Menu .........66 Serial Ports..........43 Primary / Secondary IDE Master and Slave Submenu ......67 Parallel Port.........43 Keyboard Submenu ......68 Add-in Board Slots ........43 Advanced Menu .........68 Video............44...
  • Page 5 File ............. 82 Upgrading the BIOS......102 View ............ 83 Recovering the BIOS ....... 103 Settings..........83 Changing the BIOS Language ..103 Help ............ 83 Using the Firmware Update Utility ..104 Exiting the SSU........83 Running the Firmware Update Utility 104 Emergency Management Port Console ...
  • Page 6 PCI Installation Tips ......113 10. Equipment Log and Power Consumption Worksheets..... 143 Problems with Application Software ..113 Bootable CD-ROM Is Not Detected..114 Equipment Log........143 Error and Informational Messages ..114 Current Usage........145 POST Codes and Countdown Codes114 Calculating Power Consumption..145 Worksheet, Calculating DC Power Usage POST Error Codes and Messages..118 ...........
  • Page 7 FCC Declaration of Conformity ..151 Figure 20. Server Board Connector and Component Locations........40 Electromagnetic Compatibility Notices Figure 21. Server Board Screw Hole Locations52 (International) ......... 152 Figure 22. Installing DIMMs ......53 Installation Precautions......152 Figure 23. Removing a Processor ....55 Appendix B: Glossary ......
  • Page 8 Table 19. AT Style Front Panel Connector Table 30. Narrow SCSI Connector Pinout .. 128 Pinout............123 Table 31. Wide SCSI Connector Pinout..129 Table 20. Heatsink Fan Connector Pinout .. 123 Table 32. IDE Connector Pinout ....130 Table 21. Chassis Fan Connector Pinout ... 124 Table 33.

  • Page 9: Product Shipment

    If you have questions about the way the unit functions or about any technical hardware specifications, Micron’s award winning Technical Support team is ready to help you. Support is available 24-hours a day, seven days a week. Contact us by visiting our web site at http://support.micronpc.com or telephone us toll-free at 1-800 249-1178.
  • Page 10 For parts, peripherals or upgrades, telephone MICRON ADDITIONS at 1-888 8MICRON. Micron wants to make this product guide as useful as possible and welcomes your suggestions and comments. Please provide the title, part number and page number of the document and E-Mail your...

  • Page 11: Table 1. Chassis Feature Summary

    The hardware accessory kit includes this Product Guide, three power cords, and two hardware bags: • Keyboard. • LANDesk Server Manager. • Micron Customer Resource Center Software CD. • Mouse and mouse pad. • Power cords. • The Server.

  • Page 12: Figure 1. Front Controls And Indicators

    OM05066 Figure 1. Front Controls and Indicators Diskette ejector button* Diskette drive activity LED* C. CD-ROM drive* D. System power on LED Power button Reset button G. Hard drive LED Items shown may not be included in the chassis.

  • Page 13: Figure 2. Back I/O Ports And Features

    Figure 2. Back I/O Ports and Features Network LEDs* Network connector port* † C. VGA monitor connector* D. Serial port A, COM1* Mouse and keyboard connectors* Serial port B, COM2 (extended via ribbon cable from back panel to server board)* G.

  • Page 14: Figure 3. Chassis Side View

    Figure 3. Chassis Side View 5.25-inch external bays 3.5-inch diskette drive C. Primary plastic fan housing D. Plastic front bezel Card guide assembly (secondary plastic fan behind assembly) 3.5-inch internal peripheral bay G. Power supply (behind the 3.5-inch peripheral bay)

  • Page 15: Power Supply

    An internal bay is provided for drives that are 3.5 inches wide and either 1 inch or 1.6 inches high. The possible combinations (height and quantity) are as follows: • Up to a total of six drives, each 1 inch high •...

  • Page 16: Figure 4. System Security

    NOTE The side cover must be on the system for proper cooling. To help prevent unauthorized entry or use of the system, the chassis includes a physical padlock loop and a chassis intrusion switch that can be monitored by Server Management software. Secure the side cover to the chassis by inserting a padlock (not provided) through the metal loop protruding through the slot in the back edge of the side cover.

  • Page 17: Working Inside The System

    These warnings and cautions apply whenever you remove the side cover of the system to access components inside the system. Only a Micron technically qualified person should integrate and configure the system. WARNINGS...

  • Page 18: Side Cover

    CAUTIONS Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other parts. We recommend that you do all procedures in this chapter only at an ESD workstation. If one is NOT available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis groundany unpainted metal surfaceon your system when handling parts.

  • Page 19: Figure 5. Removing The Side Cover

    OM06410 Figure 5. Removing the Side Cover Built-in handle Metal loop (for padlock) C. Retaining screws (3) CAUTION Do NOT damage EMI strips: When installing the side cover, Do NOT damage the EMI gaskets mounted on the cover. Replace any damaged strips, or the system may NOT meet EMI requirements.

  • Page 20: Figure 6. Removing The Front Cover

    1. Remove side cover. 2. Remove and save the screw from the front cover; you will need it later to reattach the cover. 3. Squeeze the two plastic tabs inside the front cover, and push them through the chassis slots. 4.

  • Page 21: Add-In Boards

    CAUTIONS Do NOT overload server board: Do NOT overload the server board by installing add-in boards that draw excessive current. ESD and handling boards: Add-in boards can be extremely sensitive to ESD and always require careful handling. After removing the board from its protective wrapper or from the server board, place it component-side up on a grounded, static-free surface or conductive foam pad—if available.

  • Page 22: Figure 7. Installing An Add-In Board

    OM06425 Figure 7. Installing an Add-in Board Expansion slot cover and screw Add-in board, use same screw CAUTION Slot covers must be installed on all vacant expansion slots. This maintains the electromagnetic emissions characteristics of the system and ensures proper cooling of system components. 1.

  • Page 23: Figure 8. Removing The Diskette Drive From The Chassis

    7. Use the screw removed earlier. Insert it into the threaded hole, and push the rounded notch against screw. Tighten it firmly to prevent the bracket from interfering with adjacent brackets. 1. Observe the safety and ESD precautions at the beginning of this chapter. 2.

  • Page 24: Figure 9. Removing The Diskette Drive From The Carrier

    OM05073 Figure 9. Removing the Diskette Drive from the Carrier Screws (4) Drive C. Carrier 1. Remove the new 3.5-inch diskette drive from its protective wrapper, and place it component-side up on an antistatic surface. Record the drive model and serial numbers in your equipment log.

  • Page 25: Figure 10. Ide Cable Dimensions

    An 18-inch long IDE cable that supports two drives is standard in the system. If you install an IDE hard drive, we recommend placing it in the lowest internal drive bay to make cabling easier, particularly if you also have an IDE device in the externally accessible bay. For proper IDE operation, note the cable length specified in the following figure.

  • Page 26: Figure 11. Remove Filler Panels And Emi Shields

    NOTES Save the filler panels and EMI shields: system EMI integrity and cooling are both protected by having drives installed in the bays or filler panels and EMI shields covering the bays. When you install a drive, save the panel and EMI shield to reinstall in case you should later remove the drive and not reinstall one in the same bay.

  • Page 27: Figure 12. Snap-In Plastic Slide Rails

    OM05074 Figure 12. Snap-in plastic slide rails Tape drive or other removable media device Tab on slide rail C. Screws (4) D. Slide rails (2) 9. Connect a power cable to the drive. The connectors are keyed and can be inserted in only one way.

  • Page 28: Figure 13. Installing A Removable Media Device

    OM06406 Figure 13. Installing a Removable Media Device Removable media device Power cable C. Data cable 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Remove the side and front covers. 3. Disconnect the power and signal cables from the drive. 4.

  • Page 29: Figure 14. Removing The Internal 3.5-Inch Drive Bay

    The internal peripheral bay has space for these possible drive combinations (height and quantity): • Four drives, each 1 inch high • Three drives, each 1.6 inches high • Two 1.6-inch drives plus two 1-inch drives 1. Observe the safety and ESD precautions at the beginning of this chapter. 2.

  • Page 30: Figure 15. Installing And Cabling A 3.5-Inch Scsi Device In The Internal Bay

    15. Attach power and signals cables to any drives installed in the bay. For proper cooling and airflow, neatly fold and secure the excess signal cable (use a tie wrap or cable clip) so that it does not drape across the server board or add-in boards. OM06412 Figure 15.

  • Page 31: Figure 16. Removing The Fan Housing Assembly

    For cooling and airflow, the system contains two removable chassis fans to cool the boards and removable media drives. The integrated power supply fan provides more cooling and airflow. Figure 16. Removing the Fan Housing Assembly 1. Observe the safety and ESD precautions at the beginning of this chapter. 2.

  • Page 32: Front Panel Board

    NOTE A general rule about the correct airflow direction: the removable fan pulls air from in front of the chassis so that it flows across the boards and out the back. Thus, the fan must be oriented for the correct airflow direction. If you place the fan so the label faces the back of the chassis, this should provide the correct orientation.

  • Page 33: Figure 17. Removing The Front Panel Board

    OM06423 Figure 17. Removing The Front Panel Board 1. Reconnect the front panel board signal cable to the server board. 2. Position the front panel board over the snap-on standoff and the threaded standoff inside the chassis. 3. Carefully press the board onto the snap-on standoff until it snaps in place. 4.

  • Page 34: Server Board

    CAUTION The Server Board is Extremely Sensitive to ESD and always requires careful handling. After removing it from the system, place it component-side up on a nonconductive, static-free surface to prevent shorting out the battery leads. If you place the board on a conductive surface, the battery leads may short out.

  • Page 35: Figure 18. Removing The Server Board

    OM06414 Figure 18. Removing the Server Board 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Place the EMI gasket over the I/O connectors on the server board. 3. Position the board over the two snap-in standoffs and threaded standoffs inside the chassis, and slide it carefully toward the rear of the system until the I/O connectors protrude through the back panel.

  • Page 36: Table 2. Power Supply Output Voltages

    4. Technical Reference The 300 watt power supply, designed to minimize EMI and RFI, provides sufficient power for a maximum configuration of the server. The input voltage ranges are: • 100-120 V∼ at 50/60 Hz; 4.6 A maximum current • 200-240 V∼...

  • Page 37: Table 3. Environmental Specifications

    Table 3. Environmental Specifications Temperature Nonoperating –40° to 70 °C (–55° to 150 °F) Operating 10° to 35 °C (41° to 95 °F); derated 0.5 °C for every 1000 ft (305 m) Humidity Nonoperating 95% relative humidity (noncondensing) at 30 °C (86 °F) Operating wet bulb Not to exceed 33 °C (91.4 °F) (with diskette drive or hard disk drive) Shock...

  • Page 38: Table 4. Server Board Features

    5. Server Board Description Table 4. Server Board Features Feature Description ® Processor Installed: Up to two Pentium II processors, packaged in single edge contact (S.E.C.) cartridges and installed in 242-pin Slot 1 processor connectors, operating at 1.8 V to 3.5 V. The system board’s voltage regulator is automatically programmed by the processor’s VID pins to provide the required voltage.

  • Page 39: Figure 19. Back Panel Connectors

    OM07054 Figure 19. Back Panel Connectors Mouse Connector Keyboard Connector C. Parallel Port Connector D. Serial Port Connector VGA Connector Network Connector G. Green NIC LED H. Orange NIC LED Table 5. NIC LEDs If it’s on If it’s blinking If it’s off Color Orange...

  • Page 40: Figure 20. Server Board Connector And Component Locations

    C D E Pri. Sec. OM06957 Figure 20. Server Board Connector and Component Locations Secondary processor connector Q. System fan connector (fan2) Primary processor connector R. Server monitor module (SMM) connector C. Processor Heatsink fan connectors Narrow SCSI connector D. Aux power connector Wide SCSI connector ATX power connector U.

  • Page 41: Processor

    Each Pentium II processor is packaged in a Single Edge Contact (S.E.C.) cartridge. The cartridge includes the processor core with an integrated 16 KB primary (L1) cache; the secondary (L2) cache; a thermal plate; and a back cover. The processor implements the MMX ™ technology and maintains full backward compatibility with the 8086, 80286, Intel386 ™...

  • Page 42: Table 6. Sample Dimm Component Combinations

    NOTE DIMM sizes and compatibility: use DIMMs that have been tested for compatibility with the system board. Contact your Micron Sales Representative or Local Dealer for a current list of approved memory modules. The table below lists some sample size combinations.

  • Page 43: Serial Ports

    The National 87309 device supports two serial ports, one parallel port, diskette drive, PS/2-compatible keyboard and mouse, and integrated Real Time Clock (RTC). The server board provides a connector interface for each port. Both serial ports are relocatable. By default, port A appears at the onboard DB9 connector and port B on the 10-pin header.

  • Page 44: Video

    The onboard, integrated Cirrus Logic CL-GD5480 64-bit VGA chip contains an SVGA controller that is fully compatible with these video standards: CGA † , EGA † , Hercules † Graphics, MDA † , and VGA. The standard configuration comes with 2 MB of 10 ns onboard video memory. The video controller supports pixel resolutions of up to 1600 x 1200 and up to 16.7 M colors.

  • Page 45: Keyboard And Mouse

    The system board includes a 10BASE-T/100BASE-TX network solution based on the Intel 82558 Fast Ethernet PCI Bus Controller. As a PCI bus master, the controller can burst data at up to 132 MBps. The controller contains two receive and transmit FIFO buffers that prevent data overruns or underruns while waiting for access to the PCI bus.
  • Page 46 All server management functionality is concentrated in the BMC. The BMC and associated circuitry are powered from + 5V_Standby, which remains active when system power is switched off and the system is still plugged into AC power. One major function of the BMC is to autonomously monitor system management events, and log their occurrence in the non-volatile System Event Log (SEL).

  • Page 47: Security

    The BIOS Setup and the System Setup Utility (SSU) provide a number of security features to prevent unauthorized or accidental access to the system. Once the security measures are enabled, you can access the system only after you enter the correct password(s). For example: •...

  • Page 48: Table 7. Software Security Features

    Taking the system out of secure mode does not change the state of system power. That is, if you press and release the power switch while secure mode is in effect, the system will not be powered off when secure mode is later removed. However, if the front panel power switch remains depressed when secure mode is removed, the system will be powered off.
  • Page 49 Table 7. Software Security Features (continued) Feature Description Disable writing to In secure mode, the system will not boot from or write to a diskette unless a diskette password is entered. To set this feature, use the SSU Security Subsystem Group. To write-protect access to diskette whether the system is in secure mode or not, use the Setup main menu, Floppy Options, and specify Floppy Access as read only.

  • Page 50: Upgrading

    Pen or pencil • Antistatic wrist strap and conductive foam pad (recommended) These warnings and cautions apply throughout this chapter. Only a Micron qualified technician should configure the system board. WARNING System Power ON / OFF: The power button DOES NOT turn the AC power to the system OFF.

  • Page 51: Peripherals

    Installing or removing jumpers: a jumper is a small plastic-encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that you can grip with your fingertips or with a pair of fine needle- nosed pliers. If your jumpers do not have such a tab, take care when using needle-nosed pliers to remove or install a jumper;...

  • Page 52: Server Board

    OM07056 Figure 21. Server Board Screw Hole Locations 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. If available, place the EMI gasket over the I/O connectors on the system board. 3. Insert screws through the mounting holes and into the threaded standoffs. Make sure the board is properly seated, and then tighten all the screws firmly (6.0 inch-pounds).

  • Page 53: Figure 22. Installing Dimms

    CAUTION Use extreme care when installing a DIMM. Applying too much pressure can damage the socket. DIMMs are keyed and can be inserted in only one way. Mixing dissimilar metals may cause later memory failures resulting in data corruption. Install DIMMs with gold plated edge connectors only in gold plated sockets.

  • Page 54: Processors

    CAUTION Use extreme care when removing a DIMM. Too much pressure can damage the socket slot. Apply only enough pressure on the plastic ejector levers to release the DIMM. 1. Observe the safety and ESD precautions at the beginning of this chapter. 2.

  • Page 55: Figure 23. Removing A Processor

    1. Observe the safety and ESD precautions at the beginning of this chapter and the additional cautions given here. If the processor has a fan heat sink, disconnect the power wire (B in the figure below) from the connector on the system board (C). 2.

  • Page 56: Figure 24. Installing A Second Processor

    OM06347 Figure 24. Installing a Second Processor Processor latches Processor in S.E.C. cartridge C. Retention module 1. Observe the safety and ESD precautions at the beginning of this chapter and the additional cautions given here. 2. If your system has one processor and you are ADDING a second, then you must remove the termination board from the secondary processor connector.

  • Page 57: Figure 25. Removing A Termination Board

    OM06348 Figure 25. Removing a Termination Board 3. If your system has one processor and you are REPLACING it, leave the termination board intact in the empty Slot 1 secondary connector. Remove the processor you want to replace. See “Removing a Processor”. 4.

  • Page 58: Figure 26. Locking In The Processor

    OM06346 Figure 26. Locking in the Processor Processor latches; must be pushed outward until they click into retention module Fan heat sink power cable; must plug into processor fan connector on system board C. Processor fan connector 9. After you have installed the processor, you must configure its speed. The lithium battery on the system board powers the real-time clock (RTC) for up to 10 years in the absence of power.
  • Page 59 ADVARSEL Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu.

  • Page 60: Figure 27. Replacing The Lithium Battery

    OM07055 Figure 27. Replacing the Lithium Battery 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Open the chassis. 3. Insert the tip of a small flat-bladed screw driver, or equivalent, under the plastic tab on the San-in plastic retainer, refer to Figure 27.

  • Page 61: Table 8. Configuration Utilities

    7. Configuration Software and Utilities This section describes the Power-on Self Test (POST) and system configuration utilities. The table below briefly describes the utilities. Table 8. Configuration Utilities Utility Description and brief procedure BIOS Setup If the system does not have a diskette drive, or the drive is disabled or misconfigured, use Setup to enable it.
  • Page 62 1. Turn power to the monitor on and then the system. After a few seconds POST begins to run. 2. After the memory test, these screen prompts and messages appear: Press <F2> key if you want to run SETUP Keyboard..Detected Mouse..Detected 3.
  • Page 63 This section describes the BIOS Setup options. Use Setup to change the system configuration defaults. You can run Setup with or without an operating system being present. Setup stores most of the configuration values in battery-backed CMOS; the rest of the values are stored in flash memory. The values take effect when you boot the system.
  • Page 64 You can enter and start Setup under several conditions: • When you turn the system on, after POST completes the memory test • When you reboot the system by pressing <Ctrl+Alt+Del> while at the DOS operating system prompt • When you have moved the CMOS jumper on the system board to the “Clear CMOS” position (enabled);...
  • Page 65 Press Get general help <F1> or <Atl+H> ← → Move between menus ↑ Go to the previous item ↓ Go to the next Item Change the value of an item + or - Select an item or display a submenu <Enter>...

  • Page 66: Main Menu

    You can make the following selections on the Main Menu itself. Use the submenus for other selections. Feature Choices Description System Time HH:MM:SS Sets the system time. System Date MM/DD/YYYY Sets the system date. Legacy Diskette A: Disabled Selects the diskette type. 360KB 1.2 MB 720KB...
  • Page 67 Feature Choices Description Type Auto Auto forces the system to attempt auto-detection of the drive type. None None informs the system to ignore this drive. CD-ROM CD-ROM allows the manual entry of some fields described below. IDE Removable IDE Removable allows the manual entry of some fields described below.

  • Page 68: Advanced Menu

    Feature Choices Description Num Lock Selects the power-on state for Num Lock. Key Click Disabled Enables or disables the audible key click. Enabled Keyboard auto-repeat rate 30/sec Sets the numbers of time per second a key will repeat 26.7/sec while it is held down. 21.8/sec 18.5/sec 13.3/sec...
  • Page 69 The PCI Configuration Menu only contains selections that access other submenus. PCI Device, Embedded SCSI Submenu Feature Choices Description Option ROM Scan Enabled Enables option ROM scan of the onboard Symbios Disabled SCSI chip. There are 2 SCSI channels that are controlled by the same option ROM.
  • Page 70 Feature Choices Description COM 1 Disabled Enabled Auto Auto forces BIOS to configure the port. OS Controlled Forces the OS to configure the port. Base I/O Address Selects the base I/O address for COM 1. Interrupt IRQ 3 Selects the IRQ for COM 1. IRQ 4 COM 2 Disabled...

  • Page 71: Security Menu

    You can make the following selections on the Security Menu itself. Enabling the Supervisor Password field requires a password for entering Setup. The passwords are not case sensitive. Feature Choices Description User Password is Clear Status only; user cannot modify. Once set, this can be disabled by setting it to a null string, or by clearing password jumper on system board.

  • Page 72: Server Menu

    You can make the following selections on the Server Menu itself. Feature Choices Description System Management Enters submenu. Console Redirection Enters submenu. PCI IRQs to IO-APIC Disabled Enabled - BIOS can describe all 24 IO APIC pins in the MP mappings Enabled table for PCI interrupts.

  • Page 73: System Management Submenu

    System Management Submenu (continued) Feature Choices Description Modem Init String AT&F0S0=1S14=0&D Sets the initialization string for the modem being used for EMP. Only used in EMP modem mode. This field is only 16 characters long. High modem Init string field is a continuation of the Modem Init string to be able to enter in another 4 characters.

  • Page 74: Boot Menu

    Feature Choices Description COM Port Address Disabled When enabled, console redirection uses the I/O port specified. 3F8 - typically is COM 1 2F8 - typically is COM 2 All keyboard/mouse and video will be directed to this port. This is designed to be used only under DOS in text mode. IRQ # 3 or 4 When console redirection is enabled, this displays the IRQ...

  • Page 75: Hard Drive

    For options on this menu, use the up or down arrow keys to select a device, then press the <+> or <-> keys to move the device higher or lower in the boot priority list. Option Description 1. Hard Drive #1 (or actual drive string) IDE drives will have a suffix attached to the drive ID string.
  • Page 76 The System Setup Utility (SSU) is on the Server System Configuration Software CD shipped with the server. The SSU provides a graphical user interface (GUI) over an extensible framework for server configuration. For the N440BX systems, the SSU framework supports the following functions and capabilities: •...

  • Page 77: Running The Ssu

    The SSU may be run directly from the Server Configuration Software CD or from a set of DOS diskettes. If you choose to run the SSU from a set of DOS diskettes, you must copy the SSU from the Server Configuration Software CD to a set of DOS diskettes and follow the instructions in the included README.TXT file to prepare the diskettes.

  • Page 78: Figure 28. System Setup Utility Main Window

    SSU consists of a collection of task-oriented modules plugged into a common framework called the Application Framework (AF). The Application Framework provides a launching point for individual tasks and a location for setting customization information. For full functionality, the SSU requires the availability of the AF.INI, AF.HLP, plus any .ADN files and their associated .HLP and .INI files.
  • Page 79 The SSU lets you customize the user interface according to your preferences. The AF sets these preferences and saves them in the AF.INI file so that they take effect the next time you start the SSU. There are four user-customizable settings: •...

  • Page 80: Defining An Isa Card

    The RCA provides three major functions: • Creates representations of devices that cannot be discovered by the system (ISA cards) • Modifies the contents of the system by adding and removing devices • Modifies the resources used by devices You can use the RCA window to define an ISA card or add an ISA card by clicking on the appropriate button.

  • Page 81: System Resource Usage

    Adding and removing cards through the RCA provides a way for the RCA to run its conflict detection algorithms on the resources requested by the cards. This alerts you to any possible problems with that particular card in the current configuration. •...

  • Page 82: Security Options

    1. Click on the user password button. 2. Enter the password in the first field. 3. Confirm the password by entering it again in the second field. 1. Click on the User password button. 2. Enter the old password in the first field. 3.

  • Page 83: View

    The View menu has the following options: • SEL Info Displays information about the SEL. These fields are display only. • All Events Displays the current SEL data from the BMC. • By Sensor Brings up a pop-up menu that allows you to view only the data from a certain sensor type.

  • Page 84: Figure 29. Emp Console In Command State

    The Console Manager also has a support plug-in Phonebook, which you can use to create and maintain a list of servers and their phone numbers. You can launch the Connect dialog directly from the Phonebook dialog to connect to a selected server. The EMP shares use of the COM 2 port with the system.

  • Page 85: Figure 30. Emp Console In Redirect State

    Figure 30. EMP Console in Redirect State Figure shows the EMP Console window in redirect state with the terminal window. The text that appears on the server monitor displays in the redirect window. Availability of the various EMP Console features is determined by two things: the EMP access mode selected during configuration in the System Management Submenu of the BIOS Server Menu, and if the server’s COM 2 port is configured for console redirect in BIOS.

  • Page 86: Table 11. Emp Console Access Modes (Server Not Configured For Console Redirect)

    Table 11. EMP Console Access Modes (Server not Configured for Console Redirect) Mode Server is powered off During POST After OS boots Disabled Redirect window appears, Redirect window appears, Redirect window appears, but is blank but is blank but is blank Pre-boot EMP commands available EMP commands available...

  • Page 87: Console Redirection Submenu

    In the EMP Password area of the System Management Submenu, type in a password of up to 8 alphanumeric characters. If a beep is heard, the password was not accepted and a different password must be entered. EMP Access Modes: Choose either Disabled, Pre-boot, or Always Active, depending on the type of EMP access needed.

  • Page 88: Toolbar

    The tool bar buttons of the EMP Console main window combine server control and management plug-in options available from the Connect and Action menus as follows: Generates the Connect dialog to allow connection to a selected server. Disconnects from the server currently connected to. Generates the Power On/Off dialog.

  • Page 89: Figure 31. Connect Dialog

    • Help - provides version information and help topics for the EMP Console. Three server control operations are available from the menu or toolbar of the main EMP Console window, remote server connection, powering the server on and off, and resetting the server. The server console mode can also be switched between EMP active and BIOS redirect modes through post-power-up and reset options.

  • Page 90: Figure 32. Power On/Off Dialog

    • Help - displays dialog level help information. Selecting Power On/Off from the Action menu allows you to power the server on or off, with post- power-up options. It generates the Power on/off dialog. Figure 32. Power On/Off Dialog Options available in the dialog are: •...

  • Page 91: Figure 33. Reset Dialog

    Selecting Reset from the Action menu generates the Reset dialog so that you can remotely reset the server with post-reset options. Figure 33. Reset Dialog Options available in the dialog are: • System Reset - resets the server with the selected post-reset options. This operation is not allowed if the server is configured in RESTRICTED mode for EMP operations.

  • Page 92: Figure 34. Phonebook Dialog

    The EMP Console provides a support plug-in known as the Phonebook. The Phonebook stores names and numbers of servers in a list that can be updated by adding, modifying or deleting entries. The Phonebook can be opened from the main menu and tool bars, or launched from the Connect dialog by clicking the Config button.
  • Page 93 • View the SEL from a file • Save the SEL to a file • View SEL summary info • View all SEL entries • View SEL info by event type • View SEL info by sensor type • Set SEL display mode to either Hex or verbose mode •...

  • Page 94: Sdr Viewer

    The SDR viewer lets you view the Sensor Data Records retrieved from the SDR repository. Options available through the SDR viewer are: • View all SDR records • View SDR entries by SDR type • View SDR summary info • Set SDR display mode to either Hex or verbose mode •...

  • Page 95: Fru / Sdr Load Utility

    FRU Viewer Menu Options The following menu options are found on the FRU viewer menu bar: • File  Close - closes the FRU viewer.  Exit - exits the EMP Console. • View  Display all Records - displays all FRU data, which consists of chassis, board, and product information.

  • Page 96: Command Line Format

    This utility is compatible with ROM-DOS Ver. 6.22, MS-DOS Ver. 6.22, and later versions. The utility accepts CFG, SDR and FRU load files. The executable file for the utility is frusdr.exe. The utility requires the following supporting files: • one or more .fru files describing the system’s field replaceable units •...
  • Page 97 DOS box is insufficient and will provide incorrect results. Programming BMC FRU area clears the SDR table, therefore the SDR table must be reprogrammed. Upon completing the programming of the FRU and SDR areas, server should be rebooted. Note: DOS users may alternatively use a ’/’ instead of the ’-’. The following information is display if -v option is included in the command line.
  • Page 98 Board Information (Type 2, 8 bytes) Manufacturer = Intel Product = N440BX Ultra SCSI Backplane Version = 681234-501 Serial Number = N03121530 Chassis Information (Type 3, 9 bytes) Manufacturer = Intel Type = Main Server Chassis Version = 000000-000 Serial Number = 9912345678 Asset Tag# Displaying FRU Area The FRU area is displayed in ASCII format when the field is ASCII or as a number when the field is...
  • Page 99 Product Information Area (Version 1, Length 80) Unicode Country Base = 00h Manufacturer Name (ASCII) = Intel Product Name (ASCII) = N440BX DP Part Number (ASCII) = 000000000000 Version (ASCII) Serial Number (ASCII) = 0123456789 Asset Tag (ASCII) END OF FIELDS CODE Displaying SDR Area The SDR nonvolatile storage area is displayed in the following hex format.
  • Page 100 Prompting for Product Level FRU Information Through the use of a Configuration File, the utility may prompt you for FRU information. Filtering Sensor Data Record From the SDR File The MASTER.SDR file has all the possible SDRs for the system. These records may need to be filtered based on the current product configuration.
  • Page 101 Cleaning Up and Exiting If an update was successfully performed, the utility displays a single message and then exits. If the utility fails, it immediately exits with an error message and exit code. Before you upgrade the BIOS, prepare for the upgrade by recording the current BIOS settings, obtaining the upgrade utility, and making a copy of the current BIOS.
  • Page 102 The BIOS upgrade file is a compressed self-extracting archive that contains the files you need to upgrade the BIOS. 1. Copy the BIOS upgrade file to a temporary directory on your hard disk. 2. From the C:\ prompt, change to the temporary directory. 3.
  • Page 103 It is unlikely that anything will interrupt the BIOS upgrade; however, if an interruption occurs, the BIOS could be damaged. The following steps explain how to recover the BIOS if an upgrade fails. The following procedure use recovery mode for the Setup program. NOTE Because of the small amount of code available in the non-erasable boot block area, there is no video support.
  • Page 104 The Firmware Update Utility is a DOS based program used to update the Baseboard Management Controller’s firmware code. You only need to run the Firmware Update Utility if new firmware code becomes necessary. 1. Create a DOS bootable diskette. The version of DOS must be 6.0 or higher. 2.

  • Page 105: Solving Problems

    8. Solving Problems This chapter helps you identify and solve problems that might occur while you are using the system. To do this: Press: Soft boot reset, which clears system memory <Ctrl+Alt+Del> and reloads the operating system. Clear system memory, restart POST, and Reset button reload the operating system.
  • Page 106 Are all cables correctly connected and secured? Are the processors fully seated in their slots on the system board? Are all add-in ISA and PCI boards fully seated in their slots on the system board? Are all switch and jumper settings on the system board correct? Are all jumpers and switch settings on add-in boards and peripheral devices correct? To check these settings, refer to the manufacturer’s documentation that comes with them.
  • Page 107 If you are running the software from a diskette, try a new copy of the software. If you are running the software from a CD-ROM disk, try a different disk to see if the problem occurs on all discs. If you are running the software from a hard disk drive, try running it from a diskette. If the software runs correctly, there may be a problem with the copy on the hard disk drive.
  • Page 108 5. Turn power to the system ON. If the power LED does not Illuminate, see “Power LED Does Not Illuminate”. A diagnostics package for the system is contained on the Configuration Software CD that comes with the system. For documentation about the test modules, see the Diagnostic help disks that end with the extension .HLP.

  • Page 109: System Cooling

    This section provides possible solutions for these specific problems: • Power LED does not illuminate. • No beep or incorrect beep pattern. • No characters appear on screen. • Characters on the screen appear distorted or incorrect. • System cooling fans do not rotate. •...
  • Page 110 4. If you do not receive a beep code and characters do not appear, the video display monitor or video controller may have failed. Contact your service representative or authorized dealer for assistance. Check the following: Are the brightness and contrast controls properly adjusted on the video monitor? See the manufacturer’s documentation.
  • Page 111 Check the following: Are the diskette drive power and signal cables properly installed? Are all relevant switches and jumpers on the diskette drive set correctly? Is the diskette drive properly configured? Is the diskette drive activity LED always illuminated? If so, the signal cable may be plugged in incorrectly.

  • Page 112: Network Controller

    NOTE Front panel hard disk LED indicates IDE and SCSI devices: the hard disk drive activity LED on the front panel illuminates when either an IDE hard disk drive, or a SCSI device controlled by the onboard SCSI host controller, is in use. This LED does Not display CD-ROM activity. Make sure you are using the drivers that are shipped on the system Configuration Software CD for the onboard network controller.

  • Page 113: Pci Installation Tips

    The controller stopped working when an add-in adapter was installed. Make sure the cable is connected to the port from the onboard network controller. Make sure your PCI BIOS is current. Try the “PCI Installation Tips” below. Make sure the other adapter supports shared interrupts. Also, make sure your operating system supports shared interrupts;...

  • Page 114: Table 12. Port-80 Codes

    Check the following: Is the BIOS set to allow the CD-ROM to be the first bootable device? When you turn on the system, POST displays messages that provide information about the system. If a failure occurs, POST emits beep codes that indicate errors in hardware, software, or firmware. If POST can display a message on the video display screen, it causes the speaker to beep twice as the message appears.
  • Page 115 Table 12. Port-80 Codes (continued) Normal Port 80 Beeps Error Codes Post Memory Manager Initialization (PMM) Post Dispatch manager Initialization Test CMOS Post error manager Initialization Set in POST flag Initialize processor registers and CPU microcode Autosize cache Enable processor cache Initialize the local bus IDE (not used anymore but here for phx std) Initialize Power Management (APM not used in Nightshade) Initialize keyboard controller...
  • Page 116 Table 12. Port-80 Codes (continued) Normal Port 80 Beeps Error Codes EISA INIT (Not used in N440BX) Display prompt “Press F2 to enter SETUP” Disable CPU L1 cache for memory test Test RAM between 512 and 640k Test extended memory (4Mb to top of memory) Test extended memory address lines Jump to UserPatch1 Configure advanced cache registers...
  • Page 117 Table 12. Port-80 Codes (continued) Normal Port 80 Beeps Error Codes Scan for User flash ROMs MP table initialization (wake up secondary processor and halt it) Set up Power Management (not used) Enable security Enable hardware interrupts Set time of day Check key lock Initialize typematic rate Initialize DMI tables...
  • Page 118 Table 12. Port-80 Codes (continued) Normal Port 80 Beeps Error Codes Prepare to boot to OS, clean up graphics and PMM areas. Try to boot with INT 19 return to video mode 3 disable PMM return to real mode disable gate A20 clears system memory reset stack Invokes INT 19...
  • Page 119 Table 13. POST Error Codes and Messages (continued) Code Error message 0260 System timer error 0270 Real time clock error 0297 ECC Memory error in base (extended) memory test in Bank xx 02B2 Incorrect Drive A type - run SETUP 02B3 Incorrect Drive B type - run SETUP 02D0...

  • Page 120: Figure 35. Connector Locations

    9. Technical Reference This chapter includes the following: • Environmental specifications • System memory map addresses • Board interrupts • Standard video modes • Electromagnetic Compatibility (EMC) notices The figure shows connector locations on the system board. This section provides pin information about the connectors.

  • Page 121: Table 14. Atx Power Connector Pinout

    Table 14. ATX Power Connector Pinout Signal Wire color Signal Wire color +3.3 VDC Orange +3.3 VDC Orange 3.3 V sense Brown +3.3 VDC Orange -12 VDC Blue Black Black +5 VDC PS-ON_L Green Black Black +5 VDC Black Black Black PWR-OK Grey...

  • Page 122: Table 16. Auxiliary Power Connector Pinout

    Table 16. Auxiliary Power Connector Pinout Signal Wire color 5V Remote sense return Black 5 V remote sense 3.3 V remote sense Orange 3.3V remote sense return Black Not connected none Not connected none Black POWER_GOOD Gray PS_ON Green COM * Black 5 VSB Purple...

  • Page 123: Table 18. Front Panel Connector Pinout

    Table 18. Front Panel Connector Pinout Signal Signal Hard disk activity LED Front panel reset switch Front panel power switch Front panel NMI switch Fan failure indicator LED Chassis intrusion switch Power fault LED +5v standby C Data line C Clock line Table 19.

  • Page 124: Table 21. Chassis Fan Connector Pinout

    The remaining two fan connectors attach to a fans equipped with a sensor that indicates whether the fan is operating. The sensor pins for these fans are routed to the BMC for failure monitoring. Each connector has the following pinout: Table 21.

  • Page 125: Table 23. Imb Connector Pinout

    Table 23. IMB Connector Pinout Signal LOCAL_I2C_SCL LOCAL_I2C_SDA Table 24. Video Port Connector Pinout Signal Signal Green Blue DDCDAT HSYNC VSYNC DDCCLK The are functionally equivalent. Table 25. Keyboard and Mouse Connector Pinouts Keyboard signal Mouse signal KEYDAT MSEDAT FUSED_VCC (+5 V) FUSED_VCC (+5 V) KEYCLK MSECLK...

  • Page 126: Table 26. Parallel Port Connector Pinout

    Table 26. Parallel Port Connector Pinout Signal Signal STROBE_L ACK_L Data bit 0 Busy Data bit 1 Data bit 2 SLCT Data bit 3 AUFDXT_L Data bit 4 ERROR_L Data bit 5 INIT_L Data bit 6 SLCTIN_L Data bit 7 18−25 Table 27.

  • Page 127: Table 29. Rj-45 Network Connector Pinout

    Table 29. RJ-45 Network Connector Pinout Signal Description Transmit data plus—the positive signal for the TD differential pair contains the serial output data stream transmitted onto the network Transmit data minus—the negative signal for the TD differential pair contains the same output as pin 1 Receive data plus—the positive signal for the RD differential pair contains the serial input data stream received from the network...

  • Page 128: Table 30. Narrow Scsi Connector Pinout

    Table 30. Narrow SCSI Connector Pinout Signal Signal TERMPWR SCD0_L RESERVED RESERVED SCD1_L SCD2_L SATN_L SCD3_L SCD4_L SBSY_L SCD5_L SACK_L SCD6_L SRESET_L SCD7_L SMSG_L SCDP_L SSEL_L SCD_L RESERVED SREQ_L RESERVED SIO_L...

  • Page 129: Table 31. Wide Scsi Connector Pinout

    Table 31. Wide SCSI Connector Pinout Signal Signal 1-16 49-50 TERMPWR TERMPWR TERMPWR TERMPWR 20-34 SCD12_L SATN_L SCD13_L SCD14_L SBSY_L SCD15_L SACK_L SCDPH_L RESET_L SCD0_L SMSG_L SCD1_L SSEL_L SCD2_L SCD_L SCD3_L SREQ_L SCD4_L SI/O_L SCD5_L SCD8_L SCD6_L SCD9_L SCD7_L SCD10_L SCDP_L SCD11_L...

  • Page 130: Table 32. Ide Connector Pinout

    Table 32. IDE Connector Pinout Signal Signal RESET_L IDEDRQ DIOW_L DIOR_L IORDY DD10 CSEL (1 KΩ p/d) IDEDAK_L DD11 IDEIRQ DD12 Reserved (N/C) IDESA1 DD13 PDIAG_L (tied to GND) IDESA0 DD14 IDESA2 IDECS1_L DD15 IDECS3_L IDEHDACT_L Keyed If no IDE drives are present, there should be no IDE cable connected. If only one IDE drive is installed, it must be connected at the end of the cable.

  • Page 131: Table 33. Isa Connector Pinout

    Table 33. ISA Connector Pinout Signal Signal Signal Signal IOCHK_L DACK2_L RESET BALE IRQ9 DRQ2 -12V Connector key Connector key SRDY_L SBHE_L MEMCS16_L +12V LA23 IOCS16_L IOCHRDY LA22 IRQ10 SMEMW_L LA21 IRQ11 SA19 SMEMR_L LA20 IRQ12 SA18 IOW_L LA19 IRQ15 SA17 IOR_L LA18...

  • Page 132: Table 34. Pci Connector Pinout

    Table 34. PCI Connector Pinout Signal Signal Signal Signal TRST_L -12 V AD16 AD17 +12 V +3.3 V * CBE2_L FRAME_L TD0 (NC) IRDY_L +5 V +5 V TRDY_L +3.3 V * INTA_L +5 V DEVSEL_L INTC_L INTB_L STOP_L +5 V INTD_L +3.3 V * LOCK_L...

  • Page 133: Figure 36. Jumper Locations

    J3J2 J5B1 OM08097 Figure 36. Jumper Locations Table 35. Server Board Jumper Summary Jumper Block Pins (default in What it does at system reset bold) A BMC Forced Update Mode 9-10, Normal System boots normally. 10-11, Program System tries to update BMC firmware. B Chassis Intrusion Detection 5-6, Enable Switch installed on chassis indicates when...
  • Page 134 Table 35. Server Board Jumper Summary (continued) Jumper Block Pins (default in What it does at system reset bold) F Password clear 5-6, Protect Maintains the current system password. 6-7, Erase Clears the password. G CMOS clear 1-2, Protect Preserves the contents of NVRAM. 2-3, Erase Replaces the contents of NVRAM with the manufacturing default settings.

  • Page 135: General Procedure To Change Jumper Setting

    The jumper at pins 1, 2, and 3 controls whether settings stored in CMOS nonvolatile memory (NVRAM) are retained during a system reset. Procedure to restore the system’s CMOS and RTC to default values: 1. See General Procedure to Change Jumper Settings. 2.
  • Page 136 4. Turn the system on, and insert the Flash Memory Update Utility diskette in drive A. After the system boots, the speaker emits a single beep and the recovery process starts. This takes about three minutes. When the recovery process completes, the speaker emits two beeps.

  • Page 137: Chassis Intrusion Detection Jumper

    The jumper at pins 5, 6, and 7 controls the FRB timers. Procedure to disable FRB timer: 1. See General Procedure to Change Jumper Settings. 2. Move the recovery boot jumper from pins 5 and 6 to pins 6 and 7. 3.

  • Page 138: Table 36. Interrupts

    The table below recommends the logical interrupt mapping of interrupt sources; it reflects a typical configuration. Use the information to determine how to program each interrupt. The actual interrupt map is defined using configuration registers in the PIIX4 and the I/O controller. I/O Redirection Registers in the I/O APIC are provided for each interrupt signal;...

  • Page 139: Table 37. Standard Vga Modes

    The 5480 integrated video controller provides all standard IBM VGA modes. With 1 MB of video memory, the system goes beyond standard VGA support. The tables below show all supported video modes using 1 MB of video memory. The following tables show the standard modes that the chip supports, including the number of colors and palette size, resolution, pixel frequency, and scan frequencies.

  • Page 140: Table 38. Extended Vga Modes

    Table 38. Extended VGA Modes Mode(s) Bits per Pixel Horiz. Vert. Min. in Hex pixel Colors Resolutio Freq. Freq. Freq. Memor (MHz) (kHz) (Hz) 58, 6A 16/256K 800 X 600 35.2 58, 6A 16/256K 800 X 600 37.8 58, 6A 16/256K 800 X 600 48.1...
  • Page 141 Table 38. Extended VGA Modes (continued) Mode(s) Bits Pixel Horiz. Vert. Min. in Hex Colors Resolution Freq. Freq. Freq. Memor pixel (MHz) (kHz) (Hz) 800 X 600 56.25 53.7 800 X 600 68.2 63.6 640 X 480 31.5 640 X 480 31.5 37.9 640 X 480...
  • Page 142 Table 38. Extended VGA Modes (continued) Mode(s) Bits per Pixel Freq. Horiz. Freq. Vert. Min. in Hex pixel Colors Resolution (MHz) (kHz) Freq. (Hz) Memor 1024 X 768 44.9 35.5 (interlaced) 1024 X 768 48.3 1024 X 768 1024 X 768 78.7 1024 X 768 94.5...

  • Page 143: Consumption Worksheets

    10. Equipment Log and Power Consumption Worksheets Use the blank equipment log provided here to record information about your system. You will need some of this information when you run the SSU. Manufacturer Name Item and Model Number Serial Number Date Installed System Server board...
  • Page 144 Equipment Log (continued) Manufacturer Name Item and Model Number Serial Number Date Installed...

  • Page 145: Table 39. Power Usage Worksheet 1

    As an overall current usage limitation on the power supply, do not exceed a combined power output of 167 watts for the +5 and +3.3 volt outputs. The ISA slots on the server board are rated at a maximum of 4.5 amperes per slot. The ISA specification recommends supporting an average of 2.0 amperes per slot.

  • Page 146: Table 40. Power Usage Worksheet 2

    Cooling fan 1 Total Current 1. From the previous worksheet, enter the total current for each column. 2. Multiply the voltage by the total current to get the total wattage for each voltage level. 3. Add the total wattage for each voltage level to arrive at a total combined power usage on the power supply.

  • Page 147: Appendix A: Information For Computer Integrators

    Appendix A: Information for Computer Integrators This server board complies with the following safety and electromagnetic compatibility (EMC) regulations when correctly installed in a compatible host computer. The Standard for Safety of Information Technology Equipment including Electrical Business Equipment. (USA and Canada) The Standard for Safety of Information Technology Equipment including Electrical Business Equipment.

  • Page 148: Regulatory Requirements

    Generic Immunity Standard. Currently, compliance is determined via testing to IEC 801-2, - 3 and - 4. (Europe) Implementation Regulations for Voluntary Control of Radio Interference by Data Processing Equipment and Electronic Office Machines. (Japan) Interference-Causing Equipment Standard, Digital Apparatus. (Canada) Limits and methods of measurement of Radio Interference Characteristics of Information Technology Equipment.

  • Page 149: Installation Instructions

    safety and regulatory requirements. If you do not follow these instructions and the instructions provided by host computer and module suppliers, you increase safety risk and the possibility of non-compliance with regional laws and regulations. Before computer integration, make sure that the host chassis, power supply, and other modules have passed EMC certification testing.
  • Page 150 Do not overload the power supply output. To avoid overloading the power supply, make sure that the calculated total current load of all the modules within the computer is less than the maximum output current rating of the power supply. If you do not do this, the power supply may overheat, catch fire, or damage the insulation that separates hazardous AC line circuitry from low-voltage user accessible circuitry and result in a shock hazard.
  • Page 151 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Micron Electronics, Inc. 900 East Karcher Road Nampa, ID 83687...

  • Page 152: Electromagnetic Compatibility Notices (International)

    WARNING Do NOT open the Power Supply. Risk of electric shock and burns from high voltage and rapid overheating. There are NO User Servicable Parts in the power supply. Refer servicing of the power supply to Micron qualified technician.
  • Page 153 To maintain the UL listing and compliance to other regulatory certifications and/or declarations, the following regulated components must be used, and conditions adhered to. Information for system configurations can be found through Intel’s web address (http://www.intel.com). • Columbus II chassis (chassis is provided with power supply and fans)UL listed. •...

  • Page 154: Appendix B: Glossary

    Appendix B: Glossary...

  • Page 160: Appendix C: Warnings

    Appendix C: Warnings WARNING: English (US) AVERTISSEMENT: Français WARNUNG: Deutsch AVVERTENZA: Italiano ADVERTENCIAS: Español...
  • Page 161 The power supply in this product contains no user-serviceable parts. There may be more than one supply in this product. Refer servicing only to qualified personnel. Do not attempt to modify or use the supplied AC power cord if it is not the exact type required.
  • Page 162 WARNING: English (continued) A microprocessor and heat sink may be hot if the system has been running. Also, there may be sharp pins and edges on some board and chassis parts. Contact should be made with care. Consider wearing protective gloves. Danger of explosion if the battery is incorrectly replaced.
  • Page 163 Le bloc d‘alimentation de ce produit ne contient aucune pièce pouvant être réparée par l‘utilisateur. Ce produit peut contenir plus d‘un bloc d‘alimentation. Veuillez contacter un technicien qualifié en cas de problème. Ne pas essayer d‘utiliser ni modifier le câble d‘alimentation CA fourni, s‘il ne correspond pas exactement au type requis.

  • Page 164: Avertissement: Français

    AVERTISSEMENT: Français (suite) Le microprocesseur et le dissipateur de chaleur peuvent être chauds si le système a été sous tension. Faites également attention aux broches aiguës des cartes et aux bords tranchants du capot. Nous vous recommandons l‘usage de gants de protection. Danger d‘explosion si la batterie n’est pas remontée correctement.
  • Page 165 Benutzer können am Netzgerät dieses Produkts keine Reparaturen vornehmen. Das Produkt enthält möglicherweise mehrere Netzgeräte. Wartungsarbeiten müssen von qualifizierten Technikern ausgeführt werden. Versuchen Sie nicht, das mitgelieferte Netzkabel zu ändern oder zu verwenden, wenn es sich nicht genau um den erforderlichen Typ handelt. Ein Produkt mit mehreren Netzgeräten hat für jedes Netzgerät ein eigenes Netzkabel.

  • Page 166: Warnung: Deutsch

    WARNUNG: Deutsch (fortsetzung) Der Mikroprozessor und der Kühler sind möglicherweise erhitzt, wenn das System in Betrieb ist. Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen. Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr.
  • Page 167 Rivolgersi ad un tecnico specializzato per la riparazione dei componenti dell’alimentazione di questo prodotto. È possibile che il prodotto disponga di più fonti di alimentazione. Non modificare o utilizzare il cavo di alimentazione in c.a. fornito dal produttore, se non corrisponde esattamente al tipo richiesto.

  • Page 168: Avvertenza: Italiano

    AVVERTENZA: Italiano (continua) Se il sistema è stato a lungo in funzione, il microprocessore e il dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l’uso di guanti di protezione. Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto.
  • Page 169 El usuario debe abstenerse de manipular los componentes de la fuente de alimentación de este producto, cuya reparación debe dejarse exclusivamente en manos de personal técnico especializado. Puede que este producto disponga de más de una fuente de alimentación. No intente modificar ni usar el cable de alimentación de corriente alterna, si no corresponde exactamente con el tipo requerido.

  • Page 170: Advertencias: Español

    ADVERTENCIAS: Español (continúa) Si el sistema ha estado en funcionamiento, el microprocesador y el disipador de calor pueden estar aún calientes. También conviene tener en cuenta que en el chasis o en el tablero puede haber piezas cortantes o punzantes. Por ello, se recomienda precaución y el uso de guantes protectores.

  • Page 171: Index

    Index AC input bus termination requirements, SCSI devices, 26, 44 power connector, 13 cables add-in board drives, requirements, 24 expansion slot cover, 11, 13, 21, 22 IDE bus length limit, 44 IDE bus slots, 43 routing for removable media bays, 27 installing, 21 Caution ISA slots, 43...

  • Page 172: Add-In Board Slots

    IDE drives, 27 drive controller, 44 IMB, 125 drive ejector button, 12 ISA, 131 enabling/disabling floppy writes, 49 locations on system board, 120 installing drive in bay, 24 narrow SCSI, 128 no booting in secure mode without password, 48 parallel port, 126 reconfiguring if cannot enter Setup, 63 PCI, 132 removing bracket from drive, 23...
  • Page 173 do not touch processor pins, 54 heat sink, fan, 54, 55 grounding clip, removable media drives, 26 hot key option limit use of 5.25-inch hard drives, 25 quick reference, 61 system board sensitive to, 34, 51 Exit menu, configuring, Setup, 75 ISA expansion slots, 38 expanded video memory, 44 PCI expansion slots, 38...

  • Page 174: Removing Dimms

    features, configuring, Setup, 68 lockout timer, seting in SCU, 45 connectors on system board, 132 embedded devices, 38 language expansion slots, 38 changing in BIOS, 103 installing add-in board, 21 lithium backup battery interrupt mapping, 138 disposing of safely, 58 removing add-in board, 22 installing, 60 slot current ratings, 145...

  • Page 175: Software Locks

    CD-ROM drive activity light, 111 narrow connector pinout, 128 confirm OS loading, 108 removing drive, 30 diskette drive light, 111 single-ended only, 25 hard drive light, 111 wide connector, 129 initial system startup, 105 SCSI controller, 44 network, 112 no characters on screen, 109 administrative password limits access to, 49 PCI installation tips, 113 changing configuration, 61...

  • Page 176: Launching A Task

    Setup FRB timer enable, jumper, 137 Advanced menu, 68 front panel connector, 123 Boot Device Priority menu, 74 installing, 35, 52 Boot menu, 74 ISA connector, 131 cannot enter, need to reconfigure diskette, network (RJ45) port, 127 parallel port, 126 changing configuration, 61 password jumper, 135 Console Redirection menu, 74...
  • Page 177 video no user-serviceable parts, power supply, 17 blanking for security, 49 power on/off switch, 17 controller, 44 Warnings expansion, 44 translations extended VGA modes, 141 English, 161 memory, 38 French, 163 resolutions supported, 44 German, 165 VGA monitor connector, 13 Italian, 167 video controller, 38 Spanish, 169...
  • Page 178 MAS001568-01 6 / 99...

Table of Contents