Advertisement

SWIMMING POOL HEAT PUMP
Owners Manual
This manual refers to the 17.0kw and 21.0kw models only.
The heat pump unit is sold with a 1 year warranty.
In addition there is a 2 year parts warranty on the compressor
and a 5 year parts warranty on the titanium heat exchanger.
Please contact your supplying dealer in the event of a claim.
This heat pump is designed for domestic use between May and September.
To achieve satisfactory performance a minimum ambient air temperature of 15° C is required.
The heat pump needs to be run for a minimum of 8 hours in 24 during the warmest part of each day.
A solar or heat retention swimming pool cover must be used.
HeatSeeker Swimming Pool Heat Pump: Page 1 of 10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WBR-17.0H-A and is the answer not in the manual?

Questions and answers

Summary of Contents for HeatSeeker WBR-17.0H-A

  • Page 1 The heat pump needs to be run for a minimum of 8 hours in 24 during the warmest part of each day. A solar or heat retention swimming pool cover must be used. HeatSeeker Swimming Pool Heat Pump: Page 1 of 10...
  • Page 2: Table Of Contents

    D. Starting the Heat Pump Setting the Temperature Checking the Status G. Changing the Mode H. Auxiliary Mode Winterising and Maintenance Troubleshooting: Error Codes K. Troubleshooting: Parameter Settings Accessories M. Technical Information HeatSeeker Swimming Pool Heat Pump: Page 2 of 10...
  • Page 3: Positioning

    12. Any heat exchanger or electric heater fitted as auxiliary heating must be installed after (down stream from) the heat pump so as to avoid pre-heating the pool water before it enters the heat pump. HeatSeeker Swimming Pool Heat Pump: Page 3 of 10...
  • Page 4 C. Sizes of Your Swimming Pool Heat Pump WBR-17.0H-A WBR-21.0H-A-S HeatSeeker Swimming Pool Heat Pump: Page 4 of 10...
  • Page 5 6. If the water flow from the pool pump is correct, the heat pump will start after a 2 - 3 minute pause due to a delayed start facility. 7. When the heat pump is operational the display will show temperatures for the pool water inlet and outlet. HeatSeeker Swimming Pool Heat Pump: Page 5 of 10...
  • Page 6: Setting The Temperature

    3. P1 is the temperature of condenser 1, P2 is the temperature of condenser 2. Note that some models have just one condenser so a reading may not be present for both P1 & 4. ROOM is the temperature of the air around the heat pump. HeatSeeker Swimming Pool Heat Pump: Page 6 of 10...
  • Page 7: Changing The Mode

    8. You may wish to cover the heat pump to protect it from the worst weather conditions but do not wrap up the unit too tightly, let air circulate around it. 9. Do not lay the heat pump on its side, always store upright. HeatSeeker Swimming Pool Heat Pump: Page 7 of 10...
  • Page 8 Check valves, filter and by-pass Defrosting Logo Cold coil / element. None. Normal function Communication error EE 08 Communication error between Check cable connection. control panel and control Call technician HeatSeeker Swimming Pool Heat Pump: Page 8 of 10...
  • Page 9: Accessories

    The heat pump has a housing and cover plate to allow the digital control panel it to be mounted remotely if required. A 5m extension line with socket for this purpose is provided with the kit. HeatSeeker Swimming Pool Heat Pump: Page 9 of 10...
  • Page 10: Technical Information

    1110 Weight Gross This product is CE marked. The HeatSeeker heat pump is tested to current EN standards: EN 55014-1:2001, EN 55014-2:1997, EN 61000-3-2:2001 and EN 61000-3-3:1995.LVD: EN 60335-2-40:2003, EN 60335-1:2002. HeatSeeker Swimming Pool Heat Pump: Page 10 of 10...

This manual is also suitable for:

Wbr-21.0h-a-s

Table of Contents