Advertisement
6. SET TRANSMITTER SWITCHES
SET OPTION SWITCH
RECEIVER BANK
STATUS REPORTS
SWITCH 2
SWITCH 1
BANK #
SWITCH 3
OFF
OFF
1
OFF
NO STATUS REPORTS
ON
OFF
2
ON
STATUS REPORTS
OFF
ON
3
ON
ON
4
AUTO RESTORAL
SET SWITCHES 1 & 2 TO SELECT THE
SWITCH 4
RECEIVER BANK THE TRANSMITTER
ACTIVATES (USED ONLY FOR 16 CHANNEL
OFF
MANUAL RESTORE
RECEIVER, USE BANK 1 FOR ALL OTHERS)
ON
AUTO RESTORE
SYSTEM CODE SWITCHES
SET SYSTEM CODE SWITCHES A & B TO
MATCH SYSTEM CODE SWITCHES A & B
IN THE RECEIVER
SWITCH "B"
SWITCH "A"
OPTION SWITCH
9. TEST SYSTEM
SLIDE BOARD INTO
CASE IN THE 3RD
SLOT UP
WARNING
NEVER CONNECT THE TRANSMITTER AND
RECEIVER ANTENNA CONNECTORS
DIRECTLY TO EACH OTHER. MAJOR
DAMAGE TO BOTH UNITS WILL OCCUR!
TRANSMITTER
APPLY POWER AND TRIGGER THE
TRANSMITTER'S INPUT
THE RECEIVER'S SIGNAL
THE TRANSMIT INDICATOR
INDICATOR SHOULD LIGHT AND
SHOULD LIGHT WHEN THE
OUTPUT SHOULD ACTIVATE
TRANSMITTER IS TRIGGERED
IF SYSTEM FAILS TEST, CHECK POWER, SWITCH
SETTINGS AND ANTENNA CONNECTIONS
7. CONNECT POWER AND TRIGGER INPUTS
INPUT SELECT SWITCH
SWITCH #
CHANNEL
SWT 1
CH 1
SWT 2
CH 2
SWT 3
CH 3
SWT 4
CH 4
SET SWITCHES 1 - 4 TO SELECT THE
NORMAL (NON-VIOLATED) STATE OF THE
INPUT TRIGGER DEVICE
SWITCH OFF = N/O
ROUTE WIRES THROUGH CASE
STRAIN RELIEF BUSHING BEFORE
CONNECTING TO TERMINALS
CAUTION: BE SURE WIRE STRANDS
DO NOT TOUCH NEARBY FUSE
FOR RUNS LONGER THAN 3' CONNECT THE
SUPPLIED 10K
SUPPLY TO THE "INPUT" TERMINAL OF THE
SENSOR SWITCH
FROM 12 VDC, 2-AMP
REGULATED POWER
SOURCE
10. COMPLETE INSTALLATION
INSTALL AND SETUP
THE COMPANION UNIT
AS DESCRIBED IN ITS
SECURE END PLATE BY
INSTALLATION
INSTALLING THE FOUR
INSTRUCTIONS
CASE SCREWS
RECEIVER
TEST SYSTEM AGAIN AFTER
COMPLETING INSTALLATION
SET INPUT SELECT SWITCH
TO MATCH INPUT TYPE FOR
EACH CHANNEL
OFF =
ON =
N/O
N/C
N/O
N/C
N/O
N/C
N/O
N/C
SWITCH ON = N/C
USE 18-24 AWG WIRE
TO CONNECT POWER
AND TRIGGER INPUTS
Ω
RESISTOR FROM THE +12V
WARNING
THIS UNIT REQUIRES 12 VDC AT 2 AMPS.
THE NO-LOAD VOLTAGE OF THE SUPPLY
NOTE: MAXIMUM POWER WIRE
MUST NOT EXCEED 17.5 VDC OR DAMAGE
RUN 25-FEET WITH 18 AWG WIRE
TO THE UNIT WILL OCCUR!
INSTALL THE TWO REMAINING
MOUNTING SCREWS
TIGHTEN WIRING STRAIN
RELIEF BUSHING TO
SECURE AND WEATHER
PROOF WIRING
8. MOUNT ANTENNA AND ROUTE CABLE
ANT-1A
USE ANT-1A ANTENNA
ANTENNA
FOR SHORT RANGE (LESS
THAN 1 MILE)
APPLICATIONS
CON-180A + CON-90A
ANGLE CONNECTOR
USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER
RANGE APPLICATIONS OR DIFFICULT
INSTALLATIONS
MOUNT ANTENNAS AS HIGH AS POSSIBLE
(A METAL MOUNTING POLE IS RECOMMENDED)
AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE
ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.
USE RG-8 FOR UP TO 100-FOOT CABLE RUNS.
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship
for twelve (12) months. The Warranty Expiration Date is labeled on the product.
This warranty extends only to wholesale customers who buy direct from Linear or
through Linear's normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as to the nature of
the dealer's warranty, if any. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use
or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and implied
warranties for fitness, are valid only until Warranty Expiration Date as labeled on the
product. This Linear LLC Warranty is in lieu of all other warranties express or
implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need
in portable wireless signaling. However, there are some limitations which must be
observed.
1 WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow
unlicensed high-power transmissions at or near the operating frequency of this product which may
interfere with, or even disable, normal operation of this radio device.
1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95
Radio Control devices. As such, they have limited transmitter power and therefore limited range.
1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
1 Changes or modifications to the device may void FCC compliance.
1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2005 Linear LLC
CON-180A
STRAIGHT
CONNECTOR
TO UNIT
215284 C
Advertisement
