Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Yiyuan Electric AP Series
Summary of Contents for Yiyuan Electric AP Series
- Page 1 Yiyuan Electric Co., Ltd www.yiyen.com AP Series Pure Sine Wave Inverter/Charger User’s Manual Version 1.0 Composer: Franklin Chu Date: Feb 12 , 2012...
-
Page 2: Table Of Contents
Yiyuan Electric Co., Ltd www.yiyen.com Table of Contents 1. Important Safety Information ........................3 1-1. General Safety Precautions ......................... 3 1-2. Precautions When Working with Batteries ....................3 2. Introduction ..............................4 2-1. General Information ........................... 4 2-2. Application..............................4 2.3 Mechanical Drawing ............................ -
Page 3: Important Safety Information
Yiyuan Electric Co., Ltd www.yiyen.com 1. Important Safety Information WARNING! Before using the Inverter, you need to read and save the safety instructions. 1-1. General Safety Precautions 1-1-1.Do not expose the Inverter to rain, snow, spray, bilge or dust. To reduce risk of hazard, do not cover or obstruct the ventilation openings. -
Page 4: Introduction
Yiyuan Electric Co., Ltd www.yiyen.com 2. Introduction 2-1. General Information APC Series Pure Sine Wave Inverter is a combination of an inverter, battery charger and AC auto-transfer switch into one complete system with a peak conversion efficiency of 88%. It is packed with unique features and it is one of the most advanced inverter/chargers in the market today. -
Page 5: Mechanical Drawing
Yiyuan Electric Co., Ltd www.yiyen.com 2.3 Mechanical Drawing... -
Page 6: Features
Yiyuan Electric Co., Ltd www.yiyen.com 2-4. Features High overload ability up to 300% rated power(20 sec) Low quiescent current, low power “ Power Saving Mode “ to conserve energy 3-step intelligent battery charging, PFC(Power Factor Correction) for charger 8 pre set battery type selector plus de-sulphation for totally flat batteries... -
Page 7: Electrical Performance
Yiyuan Electric Co., Ltd www.yiyen.com 2.5 Electrical Performance 2.5.1 Invert Topology The APC inverter/charger is built according to the following topology. Invert: Full Bridge Topology. Charge: Isolate Boost Topology The peak efficiency of APC series is 88%. Overload Capacity The APC series inverters have different overload capacities, making it ideal to handle demanding loads. - Page 8 Yiyuan Electric Co., Ltd www.yiyen.com selection*). In this stage, the batteries are kept fully charged and ready if needed by the inverter. If the A/C is reconnected or the battery voltage drops below 12Vdc/24Vdc, the charger will reset the cycle above.
-
Page 9: Solar Charger
Yiyuan Electric Co., Ltd www.yiyen.com Charging current for each model Model Current 1012E 35+/-5A 1024E 20+/-5A 1512E 45+/-5A 1524E 25+/-5A 2012E 65+/-5A 2024E 30+/-5A 2048E 20+/-5A 3012E 85+/-5A 3024E 45+/-5A 3048E 30+/-5A 4024E 65+/-5A 4048E 35+/-5A 5024E 70+/-5A 5048E 40+/-5A... -
Page 10: Power Saver
Yiyuan Electric Co., Ltd www.yiyen.com the battery. Maximum Power Point Tracking (MPPT) Function Maximum Power Point Tracking, frequently referred to as MPPT, is an electronic system that operates the Photovoltaic (PV) modules in a manner that allows the modules to produce all the power they are capable The PV-seeker Charge controller is a microprocessor-based system designed to implement the MPPT. -
Page 11: Transfer
Yiyuan Electric Co., Ltd www.yiyen.com The inverter is factory defaulted to detect load for 250ms in every 30 seconds. This cycle can be customized to 3 seconds thru the SW3 on DIP switch. Note: The minimum power of load to take inverter out of sleep mode (Power Saver On) is 25 Watts. -
Page 12: Protections
Yiyuan Electric Co., Ltd www.yiyen.com Any-Power Solution Series Any-Power Solution AVR Function LV (NA/JPN) HV (INTL) Acceptable Input Voltage Range (Vac) 0-160 0-300 Nominal Input Voltages (Vac) 168/14 176/15 (A) Line low loss N/W (On battery) 75/65 84/72 92/78 183/156... -
Page 13: Remote Control
Yiyuan Electric Co., Ltd www.yiyen.com The Low batter voltage trip point can be customized from defaulted value 10VDC to 10.5VDC thru the SW1 on DIP switch. The inverter will go to Over temp protection when heat sink temp. ≥105º C, and go to Fault (shutdown Output) after 30 seconds. -
Page 14: Audible Alarm
Yiyuan Electric Co., Ltd www.yiyen.com The Inverter can be customized into LCD type. The LCD will display the following content: 1 Greeting message of “Welcome to EYEN” 2 AC Status & Input Voltage “AC: abnormal” will be displayed when AC input is not qualified. -
Page 15: Dip Switches
Yiyuan Electric Co., Ltd www.yiyen.com T ≥ 85℃ T < 85 ℃ HEAT SINK T ≥ 85℃ TEMPERATURE T < 80℃ 100% I ≤ 50%Max CHARGER I > 50%Max I ≤ 40%Max CURRENT I > 50%Max 100% Load ≥ 50% LOAD Percentage Load <... - Page 16 Yiyuan Electric Co., Ltd www.yiyen.com It is better to shut everything down after low voltage trip than to leave your load in the risk of fire. Nobody wants to return home, finding house surrounded by fire trucks, and naughty neighborhood kids toasting hot...
-
Page 17: Installation
Yiyuan Electric Co., Ltd www.yiyen.com 3 Installation 3.1 Location Follow all the local regulations to install the inverter. Please install the equipment in a location of Dry, Clean, Cool with good ventilation. Working temperature ： ‐10℃‐40℃ Storage temperature ： ‐40‐70℃... - Page 18 Yiyuan Electric Co., Ltd www.yiyen.com APC1-1.5KW APS1-1.5KW APC2-3KW APS2-3KW APC4-6KW APS4-6KW APS1-3KW...
-
Page 19: Troubleshooting Guide
Yiyuan Electric Co., Ltd www.yiyen.com 4 Troubleshooting Guide Troubleshooting contains information about how to troubleshoot possible error conditions while using the Any Power Combi Inverter & Charger. The following chart is designed to help you quickly pinpoint the most common inverter failures. -
Page 20: Warranty
Yiyuan Electric Co., Ltd www.yiyen.com Charge continuous Back Feed Beep × × × × × × × × × × Short continuous Symptom Possible Cause Recommended Solution Inverter will not turn on during Batteries are not connected, loose Check the batteries and cable initial power up.