Advertisement
Quick Links
DF-54/EC
BY
MOTION
DETECTOR
For Use with DF-16/EC
Security Console
Installation
Instructions
(760) 438-7000 • FAX (760) 438-7043
www.linearcorp.com
4. CONNECT BATTERY
REMOVE
SCREW
AND OPEN
CASE
CONNECT 9-VOLT ALKALINE
BATTERY TO BATTERY CLIP
(PLUS SIDE UP)
NOTE:
WAIT 5 MINUTES AFTER
CONNECTING BATTERY
FOR DETECTOR
TO STABILIZE
8. ALARM TEST MOTION DETECTOR
PLACE CONSOLE IN THE
AWAY MODE
STAY OUT OF THE MOTION
DETECTION PATTERN AREA
FOR AT LEAST FIVE MINUTES
AFTER FIVE MINUTES, WALKING
IN FRONT OF THE MOTION DETECTOR
SHOULD TRIGGER THE ALARM
PLACE CONSOLE IN OFF MODE
TO STOP SIREN, CHECK THAT SENSOR
STATUS LIGHT IS BLINKING.
1. MOTION DETECTOR DETAIL
MOTION
DETECTOR
LENS
WALK
TEST
BUTTON
CASE
LOCKING
SCREW
(ON BOTTOM)
5. MOUNT MOTION DETECTOR BASE
MOUNTING THE DETECTOR
IN A CORNER IS PREFERRED
AFTER MOUNTING, SNAP
DETECTOR ONTO BASE
AND REPLACE CASE SCREW
USE SIDE HOLES
USE CENTER
HOLES FOR
FOR CORNER
WALL
MOUNTING
MOUNTING
PUNCH OUT REQUIRED HOLES
FOR SCREW MOUNTING
NOTE:
THE DETECTOR CAN
BE MOUNTED WITH
DOUBLE STICK TAPE,
9. REPLACING MOTION DETECTOR BATTERY
WHEN CONSOLE INDICATES A LOW BATTERY
FOR THIS SENSOR:
REMOVE
SCREW
AND OPEN
CASE
REPLACE THE BATTERY WITH
A FRESH 9-VOLT ALKALINE
BATTERY (PLUS SIDE UP)
USE ALKALINE
BATTERY ONLY
SNAP DETECTOR ONTO BASE
AND REPLACE CASE SCREW
WHEN FINISHED
NOTE: WAIT 5 MINUTES AFTER REPLACING
BATTERY FOR DETECTOR TO STABILIZE
2. TYPICAL INSTALLATION
DON'T POINT AT HEAT SOURCES
(HEATERS, ETC.), WINDOWS, OTHER
MOTION DETECTORS OR DOOR/WINDOW
TRANSMITTERS
FRONT
ROOM
BEDROOM
CONSOLE
BATH
KITCHEN
6. PROGRAM DETECTOR INTO CONSOLE
START IN
OFF MODE
ENTER YOUR
PRESS
SECRET CODE
LEARN
LEARN BUTTON
WALK
TEST
BUTTON
MOUNT
1
DETECTOR
6-8 FEET
HIGH
HOLD OFF BUTTON
FOR 3 SECONDS WHEN
FINISHED TO EXIT
LEARN MODE
10. IMPORTANT DETECTOR INFORMATION
1.
1. The motion detector can only trigger the alarm
when the Console is in Away Mode.
2. Except in "Walk Test", the detector must see no
motion for fi ve minutes before walking in front of
the unit will send an alarm signal.
3. When the Console is in Away Mode, the motion
detector will cause an instant alarm unless a
delayed perimeter door/window sensor is triggered
fi rst.
4. Operating temperature range:
+32° to +120° F (0° to +49° C)
R&TTE VAEE 27837, EMC, SFT, ETS
Linear Corporation declares that the apparatus
DF-54/EC complies with the essential requirements
and other relevant provisions of Directive 1995/5/EC.
3. MOTION DETECTION PATTERN
MOTION
DETECTOR
IN CORNER
MOTION
DETECTOR
(FOR INDOOR
USE ONLY)
MOUNT
DETECTOR
SO THAT
INTRUDER
WILL CROSS
2-3 METERS
BEAMS
7. WALK TEST MOTION DETECTOR
PUSH WALK
PUSH
TEST BUTTON
WALK
TO SEND SIGNAL
ENTER AN
TEST
FROM MOTION
UNUSED SENSOR
BUTTON
DETECTOR
NUMBER
UNIT WILL STAY IN
WALK TEST MODE
FOR 4 MINUTES AFTER
PRESSING WALK TEST
BUTTON THEN AUTOMATICALLY
RETURN TO "OPERATE" MODE
VERIFY THAT DETECTION
PATTERN COVERS DESIRED
AREA & THAT CONSOLE
STATUS INDICATOR LIGHTS
WHEN MOTION IS DETECTED
NOTE:
AFTER INITIAL SETUP,
WALK TEST UNIT YEARLY
I
NTERNATIONAL WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months.
The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale
customers who buy direct from Linear or through Linear's normal distribution channels. Linear does
not warrant this product to consumers. Consumers should inquire from their selling dealer as to
the nature of the dealer's warranty, if any. There are no obligations or liabilities on the part of
Linear Corporation for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to loss of property,
revenue, or profi t, or cost of removal, installation, or reinstallation. All implied warranties,
including implied warranties for merchantability and implied warranties for fi tness, are valid only until
Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of
all other warranties express or implied. For warranty service on Linear equipment return product,
at sender's expense to:
Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong
Attention: Repairs Department
REPAIRS POLICY
Charges will be made for equipment that is not in warranty, shows customer abuse, or is damaged by
the effects of lightning, water, fi re, or other abnormal happenings.Customer's equipment sent in for repair
may be repaired or replaced with new or remanufactured equipment at Linear's discretion.The customer
is always responsible for shipping and handling charges to the repairs facility. Linear will pay return
shipping and handling charges on "in warranty" products shipped back to the customer. The customer will
be billed for the return shipping and handling charges on "out of warranty" products.There will be a 50%
expedite fee for any express requests.The International Sales Manager must be notifi ed prior to the return
of product to Linear. All international returns must have an International Repair Authorization number
(IRA#). The number must be marked on all packages. Failure to do so will cause delays in processing.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless
signaling. However, there are some limitations which must be observed. The radios are required to comply with
local rules and regulations as radio devices. As such, they have limited transmitter power and therefore limited
range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio
signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifi cations
to the device may void regulatory compliance. Infrequently used radio links should be tested regularly to protect
against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to
acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.
Copyright © 2003 Linear Corporation
9 METERS
DETECTION
AREA
TOP
VIEW
SIDE
VIEW
9 METERS
WALK IN FRONT OF
UNIT WHILE WATCHING
RED LIGHT
210948 B
Advertisement
