Summary of Contents for Ace eBoard
- Page 1 Installation Guide All contents of this publication are subject to change. 2011.06...
-
Page 2: Table Of Contents
7. Calibration ---- 16 7.1 Preparation ---- 16 7.2 Installation ---- 18 7.2.1 Initial set up ---- 19 7.2.2 Screen calibration ---- 23 8. Options for eBoard set up ---- 25 8.1 Information TAB ---- 25 8.2 Option TAB ---- 26... -
Page 3: Verify Components Before Installation
Installation guide 1. Verify Components before Installation. Before hardware installation, firstly, please check if components listed below are included in the package. If you find missed one, please contact the store you purchased. Receiver Connection Software cable 2 receivers... -
Page 4: Receiver Installation
2. Receiver Installation. 2.1 Preparation. ACE eBoard is designed to be installed easily. The first step is placing two receivers correctly on the top of your whiteboard frame or mounting on the flat surface. Before installation, you firstly need to check each receiver carefully. ACE eBoard consists of 2 receivers and each unit is connected by cable. -
Page 5: For Whiteboard With Thin Frame Hung On The Wall
[step 2] Please stick steel bracket to the back side of whiteboard. 2.2.4 For mounting Receivers on the flat surface directly. ACE eBoard can be mounted on the flat surface directly without whiteboard as shown below; [step 1] Please fix receiver to the top-side of steel bracket using double-sided sticky tape... -
Page 6: Operation
Installation guide [step 2] Please stick steel bracket to the wall and tightly fix it using screw or double- sided sticky tape. NOTE: We recommend you to use small and narrow duct to hide cable for clean appearance as shown below;... -
Page 7: Connecting Beam Projector And Computer By Vga Cable
It is the last step for hardware installation. When this step is completed successfully, you are ready to use ACE eBoard in hardware side. However, in order to use ACE eBoard, Software installation is additionally required. As for SW installation, Please refer to the software installation guide. -
Page 8: Button Functions
Installation guide 3.1 Key features 3.1.1 Button functions ACE digital pen has 2 buttons executing different functions depending working environment. a. In MINT Interactive mode (Board software). Low button (close to pen tip): executes the right button of mouse. -
Page 9: How To Check The Pen Status
Installation guide 3.2.2 How to check the pen status. Press pen tip or pen button, then you can hear low beep sound generated by the pen when it works properly. 10 sec 3.3.3 Pen tip change When pen tip is worn-out, it can be replaced with new one. -
Page 10: Specification
Installation guide 4. Specification Operating size 120cm * 200cm ( 100 inch ) Technology Ultrasonic and infrared Device standard HID pen device Resolution About 900 DPI (Sampling) / Valid with 0.3mm Over 1 GHz Over 512 MB WINDOWS OS... -
Page 11: Preparation
Installation guide After HW installation, calibration and Board software need to be installed for using ACE eBoard. This manual describes the installation procedures for it. This installation procedure automatically check current components installed on your computer and additionally install control software and board software as well as missed components, necessary for ACE eBoard. - Page 12 Installation guide Launch Please choose this menu when you want to use MINT software without installing it on your computer. Install Please choose this menu when you want to Install MINT software on your computer permanently. NOTE : (1) When installation menu is not popped up automatically, please execute POPStarter.exe manually in the installation CD.
- Page 13 Installation guide NOTES: During installation of MINT software, system automatically checks whether <Microsoft .NET Framework> and <Tablet PC Platform SDK> are installed on your computer. If system failed to find them, it will automatically install those files with following steps.
- Page 14 Installation guide [Step 2] After “PNF Image Printer” pop-up window, “MINT–InstallShield Wizard” window will be displayed. Then click [next] [Step 3] Another window will be popped up to confirm destination folder for this SW installation. If you want to change default folder, click [Change] and enter folder name and click [OK].
- Page 15 Installation guide In the following popup window, click [Install] to install MINT softwares. Then InstallShield Wizard starts software installation. It takes a minute to be finished completely. [Step 5] If software installation is completed successfully, click [Finish] to exit program.
-
Page 16: Calibration
MINT User’s guide. 7. Calibration For using eBoard properly, executing calibration is very important. Calibration is always necessary whenever you changed projector position or Projected screen size. Also realignment of cursor requires this calibration to make it accuracy. - Page 17 - Exit MINT Control program and restart it again. [Checkpoint 3] Horizontal alignment and properly position projected screen . In order to make ACE eBoard work properly, you need to keep in mind 2 important things described below ① Adjust Beam projector to place “Projected screen” inside of two receivers.
-
Page 18: Installation
Installation guide 7.2 Installation When you were well aware of preparation and prepared it properly, you are ready to calibrate. Then invoke MINT Control by clicking MINT Control icon on desktop or system tray. MINT Control will display the window including “remind information” as shown below. -
Page 19: Initial Set Up
HW installation or did not change receiver position, skip this step and go to 3.2.2 Screen Calibration. In order for calculating (x,y) coordinates of pen position, eBoard should know constant distance between two receivers. That’s why we need initial setup only for the 1st installation or changed sensor position. - Page 20 Installation guide [Step 2] Choose setup mode. eBoard provides 2 setup modes at initial setup time. One is “Quick setup” and another is “Fine setup”.”Quick setup” is simplified process just requiring 9 points click. Normally, “Quick setup” is enough. But after doing “Quick setup”, when you experience accuracy problems continuously in working mode, we recommend you to execute “Fine setup”...
- Page 21 Installation guide As indicated in window, place pen at bottom of blue light on “Left receiver” and press it continuously till “RECOGNIZED” is displayed. [Sub-step 3] Click pen on the right receiver. When you got “RECOGNIZED” message from left receiver, MINT Control again displays the following window to get position value for “Right receiver”.
- Page 22 Installation guide In fine setup mode, you can execute precise calibration because MINT Control gathers more environmental parameters than “Quick setup” mode. [Sub-step 1] choose “Fine setup” mode and click [OK], Then, MINT Control displays the fine setup window like as below.
-
Page 23: Screen Calibration
2 receivers in parallel. 7.2.2 Screen Calibration. For using eBoard correctly, this step is also very important. Whenever the position or the size of projected screen is changed, you always have to execute this step mandatory. - Page 24 Installation guide [Step 2] click [Screen Calibration] MINT Control displays calibration window to get the value for screen size. [Step 3] continuously click the point at the center of circle guided by system. You need this step repetitively 9 times at different position.
-
Page 25: Options For Eboard Setup
SW is already the latest version, it displays “MINT software is already the latest version” message. You can also check eBoard connection at “connected device window” as MINT Control automatically displays currently connected device controlled by it. 8.2 Option TAB... - Page 26 Pen Speed: adjusting pen speed.. As bar goes on left side, pen speed is getting faster but writing quality is getting worse and vice versa. Station Install Position: Not applicable to eBoard. Shape of Mouse Cursor: Not applicable to eBoard Cursor position: Not applicable to eBoard.