Performance Air Flow System - GE 23 Owner's Manual And Installation

About the temperature controls.
Not all features are on all models. Your controls may be similar to the following
The temperature controls are preset in the factory at 37°F (3°C) for the
refrigerator compartment and 0°F (-18°C) for the freezer compartment.
Allow 24 hours for the temperature to stabilize to the preset
recommended settings.
Refrigerator temperatures can be adjusted between 34°F and 46°F
(1°C to 8°C), and the freezer temperatures can be adjusted between –6°F
and +8°F (–21°C to –13°C).
To change the Refrigerator temperature:
Tactile-LED Dispenser Control
The temperature controls can display both the SET temperature as well
as the actual temperature in the refrigerator and freezer. The actual
temperature may vary slightly from the SET temperature based on
usage and operating environment.
On some models, setting both controls to the warmest setting until
the display flashes (off) will stop cooling in both the freezer and
refrigerator compartments.
On other models, setting either control to the warmest setting
until the display flashes (off) will stop the cooling to the freezer and
refrigerator.
NOTE: Turning the refrigerator off via the controls on the touch
panel does not shut off electrical power to the refrigerator.
NOTE: The refrigerator is shipped with protective film covering the
temperature controls. If this film was not removed during installation,
remove it now.
Touch-LED Dispenser Control:
To change the temperature, press and release the FREEZER
TEMP/FRIDGE TEMP pad. The SET light will come on and
the display will show the set temperature. To change the
temperature, tap either the
temperature is displayed.

Performance Air Flow System

The Performance Air-Flow System is designed to maximize
temperature control in the refrigerator and freezer
compartments. This unique special feature consists of the
Air Tower along the back wall of the refrigerator and the Air
Tunnel on the bottom portion of the freezer rear wall. Placing
food in front of the louvers on these components will not affect
performance. Although the Air Tower and the Air Tunnel can
be removed, doing so will affect temperature performance.
(For removal instructions, on-line, contact us at ge.com or call
800.GE.CARES. In Canada, contact us at geappliances.ca or call
1.800.561.3344.)
4
Touch-LED Dispenser Control
NOTE: The refrigerator is shipped with
protective film covering the temperature
controls. If this film was not removed
during installation, remove it now.
or pad until the desired
:
Tactile LED Dispenser Control.
Once the desired temperature has been set, the temperature
display will return to the actual refrigerator and freezer
temperatures after 5 seconds. Several adjustments may be
required. Each time you adjust the controls, allow 24 hours for
the refrigerator to reach the temperature you have set.
The temperature controls can display both the SET temperature as well
as the actual temperature in the refrigerator and freezer. The actual
temperature may vary slightly from the SET temperature based on
usage and operating environment.
Turning the cooling system off: Tactile-LED Dispenser Control
On some models, setting both controls to the warmest setting until
the display flashes (off) will stop cooling in both the freezer and
refrigerator compartments.
On other models, setting either control to the warmest setting
until the display flashes (off) will stop the cooling to the freezer and
refrigerator.
NOTE: Turning the refrigerator off via the controls on the touch
panel does not shut off electrical power to the refrigerator.
Touch-LED Dispenser Control:
Press and release the FREEZER TEMP/FRIDGE TEMP pad.
Press to set freezer temperature to 5. The display will
show OFF. To turn the unit back on, press the FREEZER
TEMP/FRIDGE TEMP pad. Press
refrigerator temperatures to the preset points of 0°F (-18°C)
for the freezer and 37°F (3°C) for the refrigerator.
When the unit is turned back on, it will take up to 24 hours
to stabilize.
to set the freezer and