Related Manuals for AEG F89078VI-S
Summary of Contents for AEG F89078VI-S
- Page 1 F89078VI-S/M Dishwasher Lave-vaisselle User manual Manuel d’instructions PERFEKT IN FORM UND FUNKTION...
-
Page 2: Table Of Contents
CONTENTS CONTENTS INTRODUCTION ........................5 DESCRIPTION AND USE OF THE CONTROLS..............7 Upper panel ..........................7 Setting the washing program and switching on and off ..........8 2.2.1 Switching on ..........................11 2.2.2 Selecting and starting the program .................11 2.2.3 End of program ........................12 2.2.4 Interrupting a program ......................12 2.2.5... - Page 3 Rev 0.0...
-
Page 4: Introduction
INTRODUCTION INTRODUCTION Thank you for choosing one of our products. To use this dishwasher cor- rectly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your appliance’s fun- ctions. The texts are easy to understand and are complete with detailed illustrations. - Page 5 INTRODUCTION Symbols used in this manual (see tab. 1-01) DANGER. This symbol highlights information and warnings which, if not observed, may compromise personal safety or damage the appliance. This symbol highlights general information and warnings. Tab. 1-01 Rev 0.0...
-
Page 6: Description And Use Of The Controls
USER INSTRUCTIONS DESCRIPTION OF THE CONTROLS Upper panel All the dishwasher controls are grouped on the upper panel (see fi g. 2-01). The di- shwasher can only be switched on, programmed, switched off , etc. with the door open. A brief description (see tab. 2-01) of the various controls on the upper panel is given below. -
Page 7: Setting The Washing Program And Switching On And Off
USER INSTRUCTIONS On/off button Press to power the appliance. Program indicator lights These show which program is selected and whether there are any faults (Troubleshooting). Program selection button Press in sequence to select the required program. Add salt indicator light (only fi tted on some models) Shows the appliance has run out of salt. -
Page 8: User Instructions
USER INSTRUCTIONS To select the most suitable program for the dishes to wash, consult the following table which specifi es the most appropriate type of washing sequence depending on the kind of dishes and how dirty they are (see tabs. 2-02a and 2-02b). TIME CONSUMPTION PROGRAM NUMBER AND... - Page 9 USER INSTRUCTIONS TIME CONSUMPTION PROGRAM NUMBER AND DISHES AND PROGRAM MINUTES WATER ENERGY SYMBOL CUTLERY SEQUENCE kWh (2) Pans and dishes 3.9 l RINSE waiting to be Cold pre-wash 16’ 0.03 1.03 gal. washed Wash at 38°C (136.40°F) 10.6 l SHORT Slightly dirty Cold rinse.
-
Page 10: Switching On
USER INSTRUCTIONS Only run the soak program with half loads. To run programs 6, 7, 8, 9, 10 (see tab. 2-02b), select the required standard pro- gram (see programs 1, 2, 3, 4, 5 in tab. 2-02a) and then press the supplementary program button (ref. -
Page 11: Selecting And Starting The Program
USER INSTRUCTIONS 2.2.2 Selecting and starting the program • Press the program selection button (ref. 3 fi g. 2-02) several times until the in- dicator light corresponding to the required program turns on (ref. 2 fi g. 2-02); • if required, press the relative buttons to select any complementary functions (e.g.: “half-load”, “program delay”;... -
Page 12: Canceling The Current Program
USER INSTRUCTIONS 2.2.6 Canceling the current program • To cancel the current program, open the door and press and hold down the program selection button (ref. 3 fi g. 2-02) for a few seconds until the indicator lights of the fourth and fi fth programs turn on (ref. pr. 4, pr. 5 fi g. 2-03). •... - Page 13 USER INSTRUCTIONS PROGRAM DELAY (available for all programs except soak) The “Program delay” function delays the beginning of the washing program up to 9 hours from the moment in which programming takes place. This makes it possible to use the dishwasher at a certain time of day. Before programming a delay, open the door of the dishwasher, select the requi- red washing program (see para 2.2 “Setting the washing program and switching on and off ”).
-
Page 14: Switching Off
USER INSTRUCTIONS 2.2.8 Switching off At the end of the program, the dishwasher emits a short beep and the indicator lights of the fourth and fi fth program (ref. pr. 4, pr. 5 fi g. 2-04) fl ash. Turn off the appliance by opening the door and pressing the on/off button (ref. 1 fi g. - Page 15 USER INSTRUCTIONS N.B.: the display indicates the water hardness adjustment and the pro- gram delay. A dot (.) after the number means that the water hardness adjustment is being displayed. If no dot (.) appears, the program delay is being displayed. FIG.
-
Page 16: Energy Saving And Environmental Respect
USER INSTRUCTIONS ENERGY SAVING AND ENVIRONMENTAL RESPECT • Always try to run the dishwasher fully loaded. • Do not wash the dishes under a running tap. • Use the most suitable washing program for each type of load. • Do not pre-rinse. •... -
Page 17: Removing The Dishes
USER INSTRUCTIONS REMOVING THE DISHES At the end of the washing program, wait at least 20 minute before re- moving the dishes in order to allow them to cool. To prevent any water droplets on the upper rack from falling onto the dishes in the lower rack, empty the lower rack fi rst and then the upper one. -
Page 18: Troubleshooting
USER INSTRUCTIONS TROUBLESHOOTING The dishwasher can to signal a number of malfunctions by turning on various indicator lights, as described below (see following table): FAULT DESCRIPTION Acquastop failure The anti-fl ooding system has tripped (only for models fi tted with this feature). Activates in case of water leaks. Contact the technical assistance service. - Page 19 USER INSTRUCTIONS FAULT DESCRIPTION Water pump-out malfunction The appliance does not pump out the water or does so incorrectly. Make sure the drain hose is not kinked or crushed and that the siphon and fi lters are not clogged. If the problem persists, contact the technical assistance service.