Table of Contents
Advertisement
Quick Links
XX129-00-00
Network Digital Video Transmitter
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your
requirements or that the operation will be entirely error free or perform precisely as described in the
documentation. This system has not been designed to be used in life-critical situations and must not be
used for this purpose.
Copyright © 2004 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
ViconNet and its logo are trademarks of Vicon Industries Inc.
Kollector Elite, Kollector Pro, VN-306T the Workstation and their logos are trademarks of Vicon Industries Inc.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
Windows is a trademark of Microsoft Corp.
Warning: To reduce the risk of fire or electric shock,
do not expose this unit to rain or moisture.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com
Vicon Part No. 8009-8129-00-00 Section 1 Rev 1104
Advertisement
Table of Contents
Summary of Contents for Vicon VN-306T
- Page 1 Product specifications subject to change without notice. ViconNet and its logo are trademarks of Vicon Industries Inc. Kollector Elite, Kollector Pro, VN-306T the Workstation and their logos are trademarks of Vicon Industries Inc. Vicon and its logo are registered trademarks of Vicon Industries Inc.
-
Page 3: Important Safeguards
The product shows a significant change in performance. source, use a damp cloth for cleaning and do not allow 20. Replacement Parts - Use only Vicon specified replacement moisture or liquids to enter vents. parts or an approved equivalent to prevent unit damage and injury. -
Page 4: Fcc Notice
Caution: This unit contains circuit cards with integrated circuit devices that can be damaged by static discharge. Take all necessary precautions to prevent static discharge. ii ! ! ! ! FCC Notice XX129-00-00 Rev 1104 VN-306T Network Digital Video Transmitter... -
Page 5: Important Notice
This manual is delivered subject to the following conditions and restrictions: !" This manual contains proprietary information belonging to Vicon. Such information is supplied solely for the purpose of assisting explicitly and properly authorized users of the ViconNet system. !"... -
Page 6: About This Manual
Chapter 5, Configuration, describes how to configure the VN-306T using the VN Setup Software and remotely from a Workstation !" Chapter 6, Troubleshooting, provides information on what to do in the unlikely event of a VN-306T malfunction. !" Chapter 7, Maintenance, provides information on maintaining the VN-306T. -
Page 7: Table Of Contents
Rear Panel Controls and Connections......................6 Mounting................................. 6 Installing the VN-306T ........................... 7 Step 1: Connecting the Hardware ........................ 7 Step 2: Connecting External Hardware to the VN-306T ................7 CHAPTER 4: OPERATION....................9 About This Chapter............................9 Powering On the Transmitter ........................9 Powering Off the Transmitter ........................ - Page 8 Table 9-1: Recommended Coaxial Cable Types ....................17 Table 9-2: Picture Quality vs. Cable Length...................... 18 Table 10-1: Recommended Individually Shielded, Twisted-Pair Cable Types ..........19 Table 11-1: Technical Information........................20 vi ! ! ! ! List of Figures XX129-00-00 Rev 1104 VN-306T Network Digital Video Transmitter...
-
Page 9: Chapter 1: Introduction
Upon request, the VN-306T distributes its own six channels of collected video to each workstation, or to a Kollector Elite Server, over a network. Each recorder and workstation is capable of viewing a total of six simultaneous cameras while supporting archiving, system configuration and the control of pan/tilt/zoom drives. -
Page 10: Accessory Kit
ViconNet viewer software used to communicate with the VN-306T Unpacking and Inspection All Vicon equipment is tested and inspected before leaving the factory. It is the carrier’s responsibility to provide suitable delivery. Inspect the cartons upon delivery and, if damage is present, make detailed notes on the carrier’s bill. -
Page 11: Chapter 2: Quick Installation
Chapter 2 Quick Installation Figure 2-1: VN-306T Quick Installation Quick Installation ! ! ! ! 3 XX129-00-00 Rev 1104 VN-306T Network Digital Video Transmitter... -
Page 12: Chapter 3 Installation
Chapter 3 Installation About This Chapter This chapter details the complete installation of the VN-306T Digital Video Transmitter. The following sections provide information as follows: !" Unpacking the Transmitter defines how to remove the unit and accessories from the box. -
Page 13: Unit Components
Unit Components This section describes the VN-306T unit's front and rear panels. Front Panel Controls and Connections The following picture shows the VN-306T front panel. Each panel component is described in the table below. G H I G H I... -
Page 14: Rear Panel Controls And Connections
Mounting The desk or table must provide a surface of suitable strength for the VN-306T’s weight of 3.3 lb (1.5 kg). In addition, there must be area left around the cabinet to provide suitable airflow for cooling. Do not place heavy items on the cover. -
Page 15: Installing The Vn-306T
Installing the VN-306T After the transmitter is mounted permanently, follow the steps in this section to install the VN-306T unit hardware. !" Step 1: Connecting the Hardware, below !" Step 2: Connecting External Hardware to the VN-306T, page 7 IMPORTANT NOTES: The connection of external hardware may require simple hand tools. -
Page 16: Figure 3-3: Inline Resistor
Camera Dome or other type of receiver. Sensor Input When using wire connectors to connect devices to the VN-306T, refer to the guidelines described below, according to the specific device type. NOTE: Speaker (SPK) will be operational in future versions. -
Page 17: Chapter 4: Operation
With the transmitter setup as shown in Chapter 3, Installation, press the Power Switch (switch Q in Figure 3-2 on page 6) to the ON position (“I” pressed in). The VN-306T then begins its boot routine. IMPORTANT: Do not press any keyboard buttons at this time. -
Page 18: Chapter 5 Configuration
VNSetup Configuration General The VN-306T server is factory configured to operate on any Ethernet network as it is connected to it. The initial configuration of parameters must be done using dedicated configuration software called VNSetup. Before running VNSetup, verify that the VN-306T is connected directly to a PC/Workstation without a router. -
Page 19: Figure 5-1: Vnsetup
The TX selection field shows all VN-306T and IP cameras that are found on the local network. By using the MAC address of the device to be configured, (VN-306T has a MAC address sticker on the bottom of the unit), locate the desired line. -
Page 20: Installing A New Version
After applying all changes to the desired VN-306T configuration, click on Apply and allow the VN-306T to restart. The VN-306T then starts up with the new configuration. You can access it and set it up from the ViconNet software on the same Nucleus. -
Page 21: Remote Configuration
Remote Configuration For Remote Configuration information, refer to the VN-306T Software Manual XX129-3X, where X is a revision number between 0 and 9. Configuration ! ! ! ! 13 XX129-00-00 Rev 1104 VN-306T Network Digital Video Transmitter... -
Page 22: Chapter 6 Troubleshooting
If the transmitter boots, but does not display the Main Screen, reboot the unit by toggling the power switch OFF and ON. If the transmitter still fails to boot, call Vicon Technical Support. If the VN-306T does not display video, check the following: !"... -
Page 23: Chapter 7: Maintenance
CAUTION: Do not open the transmitter’s top cover for any reason. Failure to follow this instruction can result in serious injury to the user and void the manufacturer’s warranty. Maintenance ! ! ! ! 15 XX129-00-00 Rev 1104 VN-306T Network Digital Video Transmitter... -
Page 24: Chapter 8: Shipping Instructions
Use the following procedure when returning a unit to the factory: 1. Call or write to Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 25: Chapter 9: Coaxial Cable Recommendations
Let the required picture quality and cable distance provide a guide in choosing the best cable type. For cables other than the approved Vicon types below, contact the manufacturers listed below. Note that “BC” refers to bare copper and “TC” refers to tinned copper. -
Page 26: Table 9-2: Picture Quality Vs. Cable Length
1600 (500) Best picture 400 (120) 530 (160) 820 (250) ** For longer cable runs, use a Vicon Video Amplifier to obtain a suitable picture. 18 ! ! ! ! Coaxial Cable Recommendations XX129-00-00 Rev 1104 VN-306T Network Digital Video Transmitter... -
Page 27: Chapter 10: Twisted-Pair Cable Recommendations
Chapter 10 Twisted-Pair Cable Recommendations CAUTION: Careful selection of the proper cable is essential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended are installed. Materials Use a pure copper stranded conductor with or without a tin-plating to obtain a low DC resistance. Do not use cable with either a steel or an aluminum stranded conductor because these do not transfer signals effectively for long distances. -
Page 28: Chapter 11: Technical Information
Input Voltage 120 - 230 VAC ±10%, 50/60 Hz using 12 VDC output transformer. NOTE: Vicon strongly recommends the use of uninterruptible power supply systems (UPS) to prevent voltage fluctuations that can affect operation and cause damage to the equipment. -
Page 29: Vicon Standard Equipment Warranty
Software supplied either separately or in hardware is furnished on an “As Is” basis. Vicon does not warrant that such software shall be error (bug) free. Software support via telephone, if provided at no cost, may be discontinued at any time without notice at Vicon’s sole discretion. - Page 30 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288)/ 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Brussels Office Planet II - Unit E...
Need help?
Do you have a question about the VN-306T and is the answer not in the manual?
Questions and answers