Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for DEFEWAY D5010WH4
- Page 1 DVR User Manual ...
-
Page 2: Table Of Contents
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Contents Chapter One Product Description 1.1 General .......................... 3 1.2 Open CaseAnd Connect Cables…………………………………………………………………………………..…4 Chapter Two Structure Appearance Description 2.1 Panel Description ....................... 5 2.2 Product Interface Description .................... 8 2.3 Remote Control Description..................... 11 Chapter Three Description for Operation System 3.1 Turn on / off ........................ 12 3.2 Preview .......................... 12 3.3 Menu basic operation instructions .................. 12 3.3.1Enter menu mode .................... 12 3.3.2 Menu Composition instruction ................ 12 3.3.3 Exit menu mode .................... 12 3.4 Main Menu Introduction .................... 12 3.5 Video Playback ......................... 13 3.5.1 Video Search ...................... 13 3.5.2 Article replay tools .................... 14 3.6 Manual Recording ...................... 14 3.7 PTZ Control ... -
Page 3: Chapter One Product Description
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Chapter one: Product Description 1.1 General This equipment is designed specifically for the field of a number of digital security surveillance products, which uses an Embedded Processor Init (MPU) and operating systems, combined with the field of the latest IT technologies, such as video and audio encode/decode, high‐capacity hard disk recorder, TCP / IP network technology, firmware in FLASH, making system operation more stable. This equipment, with digital video and audio recorder (DVR) and digital video and audio server (DVS) features at the same time, can works not only in local independently, but also be networked to form a powerful security monitoring network. It applies to bank, telecommunications, electric power, justice, transportation, residence, factory, warehouses, water conservancy facilities and other areas and departments of the safety precautions. ... -
Page 4: Open Caseand Connect Cables
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 1.2 Open CaseAnd Connect Cables 1.2.1 open‐case inspection First of all, please check if there is apperant damage of the packing as soon as you received the products. the material can protect from the damage very well in the transportation. Secondly, take out the product, take away the protection film from the DVR to check if there is damage. Thirdly, open case, check if there is any loose of data cable of front panel, power cable, connection between fan power and mother board. 1.2.1.1 Front panel and rear panel There are instructions of how to use keys on the front panel and the interfaces on rear panel please check the model no. with the one you ordered. As for the lables on the panel, please take good care of them, which is very important to our after‐sale service. you need to offer the model no. and serail no. during the after‐sale service. 1.2.1.2 After open case,need to check Besides checking obvious damage,also need to check if there is any loose of front panel data cable,connect between power and mother board 1.2.2 HD Install make sure to install the HDD when u first use it. Page 4 of 27... -
Page 5: Chapter Two Structure Appearance Description
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Chapter Two: Structure Appearance Description Front Panel Description D5010WH4： 1.POW：Power States LED 8.REC：Manual Recording Switch 2.CH1~CH4：Single‐Screen Switch 9. PTZ：Pan/Tilt/Zoom button ... -
Page 6: Power Switch
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 1.HDD：Power State LED 8.PLAY：Video Playback Key 2. ：System Running State LED 9.ESC：Exit Key 3.CH1~CH8：Single-Screen Switch 10.MENU：Menu Key 4.POW：Power State LED 11. ▲▼ ：Direction 5.IR: Infrared Receiver ：Select Key 6.QUAD：Multi-Screen Switch Power Switch 7.REC：Manual Recording Switch D7010DH16 : ... - Page 7 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER D6012WH8 : 1．HDD：HDD Light 2． ：System Running State LED ◀▶ ：Direction Key 3．1~9：number key ...
- Page 8 6. Power Key 13. 7. FN：Reserved Key 2.2 Rear Panel Interface Description D5010WH4/D5011WH4： ...
- Page 9 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER D6010DH8/D6011FH8/D6012WH8： 1. VIDEO IN : Video input interface 8. NET: RJ‐45 network interface 2. AUDIO OUT: Audio output interface 9. USB: USB interface 3. AUDIO IN: Audio input interface (1‐2) ...
- Page 10 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3. VIDEO OUT：Video Output Connector 9. VGA: VGA output Connector 4. AUDIO OUT: Audio output Connector 10. NET： RJ‐45 Standard Network &Standard USB Connector 5. LINE IN:TALK IN 11. R485：485 Pan/Tile Device Connector 6. POWER: Power key ...
-
Page 11: Remote Control Description
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 2.3 Remote Control Description POWER Power switch DEV ... -
Page 12: Chapter Three Description For Operation System
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Chapter Three: Description of Operation System Turn on / off Confirm that AC voltage accessible matches the requirements of digital video recorder. Ensure that the digital video recorder power outlet to a good middle ground termination. Access to power, the device started 【POWER】 light is on, into the system, the panel RUN light flashing as normal conditions. 3.2 Preview Preview screen can be seen immediately after equipment is normally starts. In the preview screen you can see the system date, time, channel name. Press corresponding number key of panel or click the left mouse button, then a single image preview can be available; Press panel "QUAD" key or click the left mouse button, you can return to a multi‐screen monitoring state. 3.3 Menu basic operation instructions 3.3.1Enter menu mode 【MENU】 key to enter the device's main menu interface. 【PLAY】 shortcut keys to enter playback interface. 【REC】 shortcut keys to enter manually recording interface. 【PTZ】 shortcut keys into PTZ control interface. Note: System Login default user name: admin, password is empty, click "OK" can into menu directly. 3.3.2 Composition of the menu Menu component units mainly in the following categories: （1） Check box: providing two kinds of status options, "√" represent enable, "□" disable, use 【confirmation / 】 button or 【↑】, 【↓】 key or click the left mouse button to choose. For example: file search menu page, the "Select Channel" and the "Record mode" check box. ... -
Page 13: Exit Menu Mode
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER For example: System Configuration menu pages, the “Camera title” edit box, enter numbers, English letters, punctuation and so on. use panel key 【↑】【 ↓ 】【←】, 【→】or after positing the edit box by mouse, press " " key or click the left mouse button, then the enter keyboard appears, select the desired input target characters through the arrow keys or click the left mouse button. b) Save or Exit the editing status by pressing button【ENTER】 【CANCEL】or【ESC】 （5） Button: used to implement a specific function or enter the next setting menu, enter by clicking 【OK 】 key and the left mouse button. 3.3.3 Exit Menu mode Press button【ESC】or click the right mouse button to exit the menu mode Click the right mouse button, return to the previous menu level. 3.4 Main Menu Introduction Press MENU key or the right mouse button pop‐up the main menu, main menu consists of the following three components ... -
Page 14: Video Search
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3.5.1 Video Search Channel selection: Select the target channel, click check box to choose. "√" is checked; "□" not selected. Record mode: Select the record mode of searching, click check box to choose. "√" is checked; "□" not selected. DATE Time setting: Enter the beginning and end time in the edit box to search the video. Storage device: In the selection box select the target backup storage device. Search : After searching criteria set, click the button, the system will begin to search the corresponding video information, and list the search results. “BLUE”‐manual recording, “RED”‐regular time recording,” GREEN”‐ Motion Detection recording, ”YELLOW”‐alarm recording. ↓ Playback: Go into video playback interface, use 【↑】 【 】 【←】 , 【→】 button or mouse to set the time period, 】or left of mouse go into playback interface. click【 Cancel : back to previous menu 3.5.2 Article playback tools Select the playback file or playback by time, it will enter the video playback interface. Stop Play: Click the button , the system will stop playing and exit the playback interface Pause / Play: Click the button to pause playback, click to continue video playback. Fast forwarding: Click can fast forwarding playback. Times fast forwarding can be set by click again. Exit playback：Click “ESC” or button to withdraw playback screen at any time; After play all, it will quit ... -
Page 15: Ptz Control
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Click left mouse button to choose "manual recording" in main menu column or click button【REC】to enter its settings interface. Manual recording interface consists of several components: Channel number：correspond to the equipment video channel.“√” open；“□”close。 All On：choose all channels video settings "on" All Off：choose all channels video settings "off"。 OK：Confirm and exit。 Cancel：Click return button, it will exit Manual recording interface. NOTE：Manual recording must be stopped by manual, or it will record continually. 3.7 PTZ Control Click "PTZ control" in main menu column or click button【PTZ】to enter its settings interface Main operation of PTZ control include: directional control; horizontal sweep; zoom control; adjust the focal length; adjust aperture; PTZ speed. 3.8 Setup Menu Click "menu" in shortcut menu enter into the main menu interface, including: video inquiry, record backup, system setup, information management, information system, system logout. Page 15 of 27... -
Page 16: System Setup
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3.8.1 Video play back In the playback shortcut menu （see3.5playback） 3.8.2 video backup Choose the channel, and record mode; setup the search time, then begin search the file. After choosing the needed file from list box, click backup and ok, wait for process bar until 100% and show backup success. NOTE：USB flash disk must be FAT32 format before backup the file. 3.8.3 System Setup In the setup menu, Choose “system setup” and turn into it's sub menu. It includes: General setup, Encode setup, Record setup, Network setup, Screen setup, Video detection, PTZ setup, Sensor setup. 3.8.3.1 General setup Page 16 of 27... -
Page 17: Encode Setup
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Choose the "General setup" and turn into it’s setup interface. Date Time：The real time when preview, click “Apply” after setting, make sure saving when it shows “Record stopped during setting time. Are you sure to continue?” Click ”Yes” to save. Date Format: “Y/M/D”、“D/M/Y”、“M/D/Y” Auto logout: Enable, the present user will log off if there is no operation in 10 minutes, it needs login again. Disable, won’t log off. Key Buzzer：Enable, there is sound with the controller or pressing key on front panel, disable, without sound. Language：There is multiple choice according to users, Chinese and English and so on. Video standard：PAL and NTSC are all available. Remote ID：Controller connect by device number when it is used to control. The remote controller should be correspond with the ID so that it can work. After setting finished, click "ok", the information will be saved. Click "cancel" to exit without saving. 3.8.3.2 Encode setup Select “Encode setup” in system setup. Channel ：Choose the right CH you like by clicking the select box Stream ：Choose the right stream: "main stream" or "sub stream" Encode mode：Choose the right encode model you need: "video only "means only encoding for video; "AV stream" means encoding for both video and audio. Page 17 of 27... - Page 18 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Bitrate mode ：Choose the right bitrate mode you need: "constant bitrate" means system encoding video as user‐defined bitrate and frame rate. "Variable bitrate" means system encoding according to user‐defined image quality and video frame rate, but bit rate is automatically adjusted by the system depending on the video screen. "Average birtrate" means system automatically adjusted fluctuation as user‐ defined bitrate. Encode format：Encoding resolutions defined by user' need （QCIF）176*144/（CIF）352*288/ (HD1)576*288/ （D1）704*576 Bitrate：Users select the encoding bitrate as needed. The higher bitrate , the better image but with large disk space. Quality：Image quality, user identified. Frame rate ：Users select the video frame rate as needed. The higher frame rate , the better image but with large disk space. Copy to ：Select the target channel on the right of "copy to "button ,click "copy to" & ''ok " then system will set the current channel setup information to other target video channel. Click button "cancel", the setup information is non‐saved but to exit. 3.8.3.3 Recode setup Select “Record setup” in system setup. Channel ：Choose the right CH as needed by clicking the inverted triangle Week day : Choose the right day as user's need, "ALL" means all days in a week. Record mode and time ：Every time slot can set different recoding mode in all 4 time slot. " Time " recording with red color ,"Motion" recording with green color ,"Sensor" recording with yellow color ;“ √ " means working ,“□” means invalid. The bottom parts has times status display, whole schedule from time 0~24 hours Copy to ：Select the target channel on the right of "copy to "button ,click "copy to" & ''ok " then system will set the current channel setup information to other target video channel. Click button "cancel", the setup ...
-
Page 19: Network Setup
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3.8.3.4Network setup Select “Record setup” in “system setup”. DHCP： Select whether to start up DHCP to automatically obtain IP 。“√”means works ；“□” means non‐work IP address: The IP address must be unique and cannot be in conflict with the host or workstation on the same network segment. Subnet Mask: Subnet for the network segment. Gateway： Need to set the gateway address to achieve communication between the different network segments. MAC address：Showing the device's MAC address Web port ：Port number IE browser visit , default port is "80" Client port : Port number device and mobile visit , suggest to set above 2000 ESee ID： After connecting internet , click “ Esee ” to gain a Esee ID , which can be used in IP remote monitoring in ESeenet network server PPPOE : Enable ：“√” means to start up PPPOE dial‐up. “□” means not to start up Username： Input the user name of ISP into edit box Password ：Input the password of ISP into edit box After the page setup is completed, click '"OK " to save the changes ; click "cancel " , non‐save but exit. DDNS: Automatic analytical function of dynamic domain name, supported 3322/DYNDNS/NO‐IP etc. DDNS provider. Enable ：“√ ”means DDNS dynamic domain services start using ;“□”means not to start up。 Select the right DDNS provider and input user name, password and domain name.（edit method please refer to 3.3.2(4)） Page 19 of 27... -
Page 20: Screen Setup
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3.8.3.5 Screen setup Select “Screen setup” in “system setup” Channel ：Choose the right CH as needed by clicking select box Camera title ：Edit any channel title as needed OSD Alpha：OSD menu transparency. Can be adjusted as needed Auto Switch Dwell Time ：The time of auto switching preview image, can be single screen or 4 Channels screen. Enable ：“√”start using ，“□” non‐start using After the page setup is completed, click '"OK " to save the changes; click "cancel", non‐save but exit. 3.8.3.6 video detection Select ”Video detection” in the “system setup”. Sensor ：Choose the right CH as needed by clicking the inverted triangle Sensitivity ：Choose the trigger video detection sensitivity Detection type ：Select detection type ‐‐motion, video loss, video cover. Alarm duration: After choose the trigger video detection, the time alarm last Area edit: Set motion detection area; move by choosing left of mouse. Alarm:“√” means start ，“□”means non start Buzzer :“√ ” means start ，“□” means non start E‐Mail notice ：“√” means E‐Mail valid，“□” means E‐Mail invalid Copy to ： select the target channel on the right of "copy to "button ,click "copy to"&''ok " then system will set the current channel setup information to other target video channel. Click button "cancel", the setup ... -
Page 21: Sensor Setup
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3.8.3.7 PTZ Control Select ”PTZ setup” in “system setup” Channel: Choose the right channel, click the select box to choose Protocal: The selected one must be the same with the one of PTZ camera. Device ID: Input the address of appointed decoder. Baudrate: Choose the matched one of the PTZ camera. Copy to: Choose the object route in the right select box, click the button of copy setting, then the information of setting will be showed, which also can be applied in other object routes. After the setting, click the button of sure to exit with saving save the changes, or click the button of “cancel” to exit without saving. 3.8.3 8 Sensor setup In system setup , choose "PTZ setup",enter setting interface Channel: Choose the right channel, click the select box to choose Work mode: Setting to start alarm or not Alarm duration: Set up alarm duration time Recording channel: When alarm is triggered, channel needed to be recorded Alarm: “√” enable alarm, “□” close alarm Buzzer: “√”start buzzer, “□” close buzzer E‐Mail notice ：“√” means E‐Mail valid，“□” means E‐Mail invalid Copy to: Choose the target channel in the right select box, click" copy to" ,the setting information will be applied to other channel. After the setting, click "OK" to exit with saving save the changes, or click "cancel" to exit without saving. Page 21 of 27... -
Page 22: System Tools
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 3.8.4 System tools In main menu, choose"system tool",enter setting interface, it includes four interface of user management, HDD management,system maintainance and factory setting 3.8.4.1 user management ... -
Page 23: System Maintencance
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER In the "System tools", click "HDD management", enter setting interface Overwrite: “√”earliest recording files will be covered when the disk is full, “□"shows not cover. Format: “√” stands selected, “□” stands not selected, when click "format" a confirm interface will pop up, then click confirm to format, click “cancel” to return the main interface 3.8.4.3 System maintenance In the "System tools", click "HDD management". System upgrade: copy the upgraded file to the root directory of USB drive, select the USB storage device, then click "Start" to upgrade the system. After upgrading, click "OK" then system auto reboot. 3.8.4.4 Factory setting In the " System tools", click "factory setting" Select the terms which need factory setting, click "OK" to save and exit or click "cancel" to exit without saving. Remarks: After factory setting, all the settings will be the initial one, please use carefully. 3.9 system information In the main menu, click "system information" which include HDD information, system information and system log. ... -
Page 24: System Information
USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER The list box shows the HDD status information 3.9.2 System information Device name, device model, H/W version, S/W version could be check here. 3.9.3 System log Choosing the log type which need checking from list box, First select the type in the , and input the time in the edit box, then click" search", the relevant information will showed below, you can turn the page by click " former" and "next", or input the No. of the page. ... - Page 25 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER Chapter Four: WEB OPERATION 4. WEB OPERATION 4.1 Connect DVR with network and insure it is running. 4.2 Setup the UPNP function from Router: this Router is TP‐LINK, just find the UPNP out and setup. 4.3 Turn into DVR: click right button of mouse‐setup‐system setup‐network setup as below: IP Address： The default IP address is192.168.1.114 （fill out according to your actual situation， If IP without conflict, no need to change.) Subnet Mask：The default subnet mask is 255.255.255.0 Gateway：The default gateway is 192.168.1.1（can be change according to the actual situation）routers running status can check from segment. ...
- Page 26 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER DNS Address：The default DNS address is192.168.1.1, can change into user's network DNS. (check the DNS address from router) After full fill all the information and save, exit to menu then turn into above menu again. 4.4 IE browser visit (use IP address mode) 4.4.1 Open IE on a computer on the same network. Input the IP address of the DVR in IE address bar and press enter . If HTTP port is not 80, add the port number after IP address. Such as http: //192.168.1.158 4.4.2 When you access the DVR’s log in screen, the browser will ask you to install the Active X plug‐in (add‐on), if it is not already installed in the browser. Proceed with the installation. 4.4.3 Click “Install”, the re‐open the browser, the following tips will shown as below. ...
- Page 27 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 4.5 IE browser visit (use P2P mode) 4.5.1 Open IE on a computer, Input www.ismartp2p.com. Input Esee ID(see3.8.3.4Network setup) into Device ID, username and password as DVR. Default user name: admin, passwords: nothing. 4.5.2 Click “login”, the browser will ask you to install the controls (plug‐in), if it is not already installed in the browser. Proceed with the installation. Page 27 of 27...
- Page 28 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 4.5.3 Click “Install”, the re‐open the browser, the following tips will shown as below. 4.5.4 Click “Run”, the re‐open the browser, the following tips will shown as below. 4.5.5 Click “Next”, then according to the prompt to install step by step, until shown the following tips. Page 28 of 27...
- Page 29 USER' S MANUAL OF EMBEDDED DIGITAL VIDEO RECORDER 4.5.5 Click “Finish” to complete the installation. 4.5.6 Open IE on a computer, Input www.ismartp2p.com. Input Esee ID(see3.8.3.4Network setup) into Device ID, username and password as DVR. Monitoring homepage including: preview window, PTZ control, preview mode, code stream selection, channel opening, setting, playback, user logout. Turn on preview：click the target channel with left button of mouse, red color means select already. Double click the channel can open or close the correspond preview channel, such as: open ...
Need help?
Do you have a question about the D5010WH4 and is the answer not in the manual?
Questions and answers