Summary of Contents for Cohu HD ER 8800
- Page 1 Helios Products Series INSTALLATION MANUAL ER 8800 Long-Range Video Camera Technical Manual 6X-1110B www.CohuHD.com info@CohuHD.com July 15, 2014...
-
Page 2: Table Of Contents
Table of Contents About this document Additional information and documents related to the camera system Copyright/Intellectual Property Rights statement Support services Returns Safety instructions Grounding 1.0 Introduction 1.1 Optional Accessories 2.0 Installation 2.1 Test Cable Requirements 2.2 CohuHD-Manufactured Test Cables (ER8900E1) 2.3 Connector Pinouts 3.0 Mounting Methods 3.1 Standalone Camera System Mounting Methods... -
Page 3: About This Document
About this document This manual contains information on the installation and maintenance of the CohuHD ER8800 Series Long Range Standalone Camera System. Please read this manual carefully prior to installation to prevent any accidental damage or misuse. The manual is available from the CohuHD website at: http://www.CohuHD.com/Files/install_manuals/ER8800_IM.pdf The information in this manual is subject to change without notice. -
Page 4: Returns
Returns This item was thoroughly tested and carefully packed at the factory prior to shipping. Upon acceptance by the carrier, the carrier assumes responsibility for the item’s safe arrival. If you receive the item in a damaged condition, apparent or concealed, a claim for damage must be made to the carrier. If a visual inspection shows damage upon receipt of this shipment, it must be noted on the freight bill or express receipt and the notation signed by the carrier’s agent. -
Page 5: Safety Instructions
Safety instructions WARNING: Do not open enclosures. There are no user-serviceable parts inside. CAUTION: In order to avoid deterioration of the color filter of the sensor and potential discoloration of the image avoid pointing the camera directly toward the sun or other bright source. CAUTION: Secure the camera system before the power is applied. • Installation must be done by qualified installers, and conform to all local codes. • It is the user’s responsibility to ensure that the mounting methods are safe and adequate for the location. -
Page 6: Grounding
Grounding • To provide protection against electrical surges induced by lightning, static charges, or any other cause, the camera and cabling system must be properly grounded to earth. For installation on a building, the camera must be bonded (that is, provided with a low impedance connection) to the building’s structural earth ground system. -
Page 7: Introduction
1.0 Introduction The CohuHD’s ER8800 series includes a standalone camera system with a high performance zoom lens made for long range applications. With long range lens and accessory options, the ER8800 line is designed for the rigorous environments and requirements for border, port, and shipboard security, as well as range safety, intruder detection, and other targeting or tracking applications. -
Page 8: Installation
2.0 Installation This chapter covers the general installation and cable requirements of the ER8800 series. NOTE: All graphics contained within this document, including screenshots and other displays, are for reference use only and are subject to change. Before starting installation: •... -
Page 9: Test Cable Requirements
2.1 Test Cable Requirements To build the test cable, CohuHD recommends: • AC38 Composite Cable. The maximum recommended cable length is 22 m (75’). 2.2 CohuHD-Manufactured Test Cables (ER8900E1) CohuHD-manufactured cables are available for ER8800 series camera systems operating from 24 Vdc. The ER8900E1 cable is intended for applications where the 24 Vdc power supply is located within 20 feet of the camera. -
Page 10: Mounting Methods
3.0 Mounting Methods CAUTION: Do not allow the full cable weight load to be placed solely at the camera system connector. WARNING: It is the user’s responsibility to ensure that the mounting methods are safe and adequate for the location. The ER8800 series is designed for outdoor installation. - Page 11 4. Corner mount kit: CohuHD p/n 8186-4 The kit includes: Wall mount: CohuHD p/n 7411417-001 Adjustable head: CohuHD p/n 7411558-005 Large corner mount: CohuHD p/n 7411425-001 Support strut: CohuHD p/n 7411558-003 Small corner mount: CohuHD p/n 7411558-004 5. Parapet mount kit: CohuHD p/n 8186-5 The kit includes: Parapet mount: CohuHD p/n 7411426-001 Wall mount: CohuHD p/n 7411417-001...
-
Page 12: Standalone Camera System Mounting Methods
3.1 Standalone Camera System Mounting Methods 3.1.1 Pedestal Mount Installation. CohuHD p/n 8186-1 Use the adjustable head and wall mount for installation on a pedestal. See Figure 3 for a typical installation diagram and Figures 13 and 14 for mount dimensions. Bolt, Hex Head 1/4-20x3/4”L, SS (3) Washer, Spring Lock 1/4”, SS (3) Adjustable Head... -
Page 13: Wall Mount Installation. Cohuhd P/N 8186-2
3.1.2 Wall Mount Installation. CohuHD p/n 8186-2 Use the adjustable head, wall mount, and strut for installation to a wall. See Figure 4 for a typical installation diagram and Figures 14, 16, and 17 for mount dimensions. Adjustable Head Bolt, Hex Head 1/4-20x3/4”L, SS (3) Washer, Spring Lock 1/4”, SS (3) Washer, Flat 1/4”, SS (3 ) Bolt, (1) -
Page 14: Pole Mount Installation. Cohuhd P/N 8186-3
3.1.3 Pole Mount Installation. CohuHD p/n 8186-3 Use the adjustable head, wall mount, support strut, large pole mount, and small pole mount for installation to a pole. See Figure 5 for a typical installation diagram and Figures 14, 16, 17, and 18 for mount dimen- sions. -
Page 15: Corner Mount Installation. Cohuhd P/N 8186-4
3.1.4 Corner Mount Installation. CohuHD p/n 8186-4 Use the adjustable head, wall mount, support strut, large corner mount, and small corner mount for instal- lation to a corner. See Figure 6 for a typical installation diagram and Figures 14, 16, 17, and 19 for mount dimensions. -
Page 16: Parapet Mount Installation. Cohuhd P/N 8186-5
3.1.5 Parapet Mount Installation. CohuHD p/n 8186-5 Use the adjustable head, wall mount, and parapet mount for installation to a parapet. See Figure 7 for a typical installation diagram and Figures 14, 16, 17, and 20 for mount dimensions. Adjustable Head Bolt, Hex Head 1/4-20x3/4”L, SS (3) Washer, Spring Lock 1/4”, SS (3) Washer, Flat 1/4”, SS (3 ) -
Page 17: Installation Procedure
3.1.6 Installation Procedure Provisions must be made for routing the system cable up to the camera system location: • Pole mounting: if the cable routes up through the pole, support the cable inside the pole to strain relieve the camera connector. •... - Page 18 • A pole or a corner: Attach the wall mount to the studs on the large pole or large corner mount and secure with the 5/16-inch nuts and washers (supplied). See Figures 5 and 6. • A parapet: Position the wall mount over the flange holes. Secure with four 5/16-inch fas- teners (not supplied). •...
-
Page 19: Overall Dimensions
3.2 Overall Dimensions 26.5 (673.1) 8.5 (215.9) 9.8 (248.9) 11.9 (302.3) 4.8 (121.9) Dimensions in inches (mm) 3.3 Mounting Hole Pattern 2.75 (69.85) 2.00 (50.8) .625 (15.9) 1/4-20 Thread (Swage nut, 5 places) .625 (15.9) 2.00 (50.8) Dimensions in inches (mm) 6X-1110B... -
Page 20: Mounting Brackets Dimensions
3.4 Mounting Brackets Dimensions Ø .38 (9.7) 4.75 (120.7) BC Ø 6.00 (152.4) 10.00 (254.0) Ø 8.50 (215.9) Ø .38 (9.7) 7.00 (177.8) BC Figure 13. Pedestal Mount. Dimensions in inches (mm) CohuHD p/n 7411542-001 3.47 3.00 (88.1) (76.2) 1.00 (24.5) 2.84 (72.1) 1.00 (24.5) Figure 14. - Page 21 Ø.38 x Ø4.75 B.C. (Ø9.7 x Ø120.6) 1/4-20 x Ø2.25 B.C. (Ø57.2) Ø6.00 (152.4) 18.50 (469.9) 20.00 (508.0) Figure 16. Wall Mount. Dimensions in inches (mm) CohuHD p/n 7411417-001 Clamp Wall Mount Clamp Swivel 17.0 (480.0) Wall Swivel Support Strut Figure 17.
- Page 22 0.75 X 0.25 SLOT (11.9 X 6.4), 6X 7.00 (177.8) 1.012 3.50 (25.7) (88.9) 4.00 5.00 (101.6) (127.0) 7.00 0.50 (178.7) 0.812 (12.7) (20.6) 12.77 (324.3) 2.75 5.00 (69.9) (127.0) 4.00 6.50 (101.6) (165.1) 5/16-18 X 1-1/4 STUD 1.75 4X EQUALLY SPACED (44.5) ON A Ø4.75 (120.6) BC 0.50...
- Page 23 The parapet mount: • Installs on the inside of a parapet that is at least 18 inches (457.2 mm) high. • Has sixteen 0.37-inch (9.4 mm) diameter holes for mounting to a parapet with fasteners of a suit- able size. Fasteners are not supplied. •...
-
Page 24: Quick Check
4.0 Quick Check NOTE: All graphics contained within this document, including screenshots and other displays, are for reference use only and are subject to change. 4.1 Control and Viewing of Camera The WinMPC GUI software is designed to work with the ER8800 Series to view video and control lens and camera. -
Page 25: Maintenance
5.0 Maintenance The system is intended for long-term unattended use, and maintenance requirements are minimal: • Clean exterior as needed. • Clean the front window on the camera head as needed. Use soft nonabrasive cloth, like terry cloth or microfiber cloth, and a foaming glass cleaner. If present, clean the wiper blade and inspect it. Replace the blade if necessary. •... -
Page 26: Schrader Valve
5.1.1 Schrader Valve The Schrader Valve is used to pressurize the housing. To maintain pressure in the barrel, add dry nitrogen to approximately 5 psi (34 kPa). 5.1.2 Pressure Relief Valve The Pressure Relief Valve limits the maximum pressure in the camera head to approximately 20 psi (138 kPa). -
Page 27: Warranty
6.0 Warranty Please refer to the CohuHD website for product warranty information: http://www.CohuHD.com/warranty/WarrantyStatement.pdf. 7.0 ER8800 Series Variants Applicable to the Manual • 8882-7201/P55A Revision History Revision Date Comments Rev A 10/28/13 Initial release • the manual is revised to change company name Rev B 7/15/14 6X-1110B...
Need help?
Do you have a question about the ER 8800 and is the answer not in the manual?
Questions and answers