Summary of Contents for VIA Technologies VT6212L
- Page 1 VIA VT6212L USB 2.0 PCI Card User Manual Ver. 1.00 All brand names and trademarks are properties of their Respective owners. Apr/05 MN0VIA621206...
-
Page 2: System Requirements
Mac® OS 10.1 or Above 32MB of RAM Available PCI Slot CD-ROM Drive(for driver installation) Specifications VIA VT6212L chipset USB 1.1 and 2.0 Compliant Up to 480 Mbps (Megabits-Per-Second) Data Transfer Rate 40 Times Faster Than The USB 1.1 Hot Swappable Plug-n-Play 2 External Type A USB 2.0 Ports... -
Page 3: Hardware Installation
Hardware Installation Be careful with polarity of the USB connector(USB3). Check the pin assignment while you connect the USB cable. Apr/05 MN0VIA621206... - Page 4 Pin No. Definition Power Power USB3 D- USB4 D- USB3 D+ USB4 D+ No Pin 1. Remove your computer’s cover. (Note: If necessary, consult your computer’s manual for help in removing the cover) 2. Locate an available PCI slot and, if necessary, remove the expansion slot bracket.
-
Page 5: Driver Installation
Driver Installation Windows®98SE Installation Make sure your version of Windows® is 98 Second Edition by check the “Properties” of “My Computer”. 1. Windows will detect new hardware and start the “VIA Tech 3038 PCI to USB Universal Host Controller” driver search program. As Figure 1. - Page 6 Figure 1 2. Select “Search for the best driver for your device” in Figure 2. Click “Next”. Apr/05 MN0VIA621206...
- Page 7 Figure 2 3. Don’t select any location and click “Next”. As Figure 3 Apr/05 MN0VIA621206...
- Page 8 Figure 3 4. Select “The updated driver(Recommended) VIA Tech 3038 PCI to USB Universal Host Controller”. As Figure 4. Click “Next”. Apr/05 MN0VIA621206...
- Page 9 Figure 4 Click “Next” again to confirm the driver and begin installation. Please insert the disk labeled “Windows 98 CD disk”. 6. After driver installation finished, click “Finish”. 7. Next, you will see Windows find a “VIA Tech 3038 PCI to USB Universal Controller”...
- Page 10 Figure 5 9. Insert the Driver CD into the CD-ROM drive of your computer. Browse to the VIA USB 2.0 Driver Folder “\PCI_IO\Viausb20” on the Driver CD, then double-click the installation file “Setup.exe”. Follow the on-screen instructions, then reboot when prompted. As Figure 6.
- Page 11 Figure 6 10. Once you have rebooted, your USB 2.0 Four Port PCI Card is ready to be used. If you open the Device Manager, you will see the newly installed devices. As Figure 7. To locate the Device Manager right click “My Computer”...
-
Page 12: Windows® Me Installation
Figure 7 Windows® ME Installation 1. Windows will detect the USB 2.0 Four Port PCI Card and automatically install drivers for all known USB devices. Follow the installation to restart the computer. As Figure 8. Apr/05 MN0VIA621206... - Page 13 Figure 8 2. After you have rebooted, Please insert the Driver CD into the CD-ROM drive of your computer. Browse to the VIA USB 2.0 Driver Folder “\PCI_IO\Viausb20” on the Driver CD, then double-click the installation file “Setup.exe”. Follow the on-screen instructions, then reboot when prompted.
- Page 14 Figure 9 3. Once you have rebooted, your USB 2.0 Four Port PCI Card is ready for operation. Open Device Manager, you will see the newly installed devices. As Figure 10 Apr/05 MN0VIA621206...
- Page 15 Figure 10 Apr/05 MN0VIA621206...
-
Page 16: Windows® 2000 Installation
Windows® 2000 Installation Windows® 2000 operating system natively supports this USB 2.0 Four PCI Card. No Drivers are necessary However, please ensure you have the latest Service Pack installed. Windows® 2000 Service Pack 4 (or later) Windows® XP Installation Windows® XP operating system natively supports this USB 2.0 Four Port PCI Card.