Table of Contents
Advertisement
Quick Links
Installation Instructions
for Topload Washers
Inside.....................................
Washer Dimensions...........................................................
Before You Start................................................................
Installation.........................................................................
Installer Checklist..............................................................
Date Purchased ________________
Model Number ________________
Serial Number _________________
Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com.
Keep these instructions for future reference.
(If this machine changes ownership, this manual must accompany machine.)
www.speedqueen.com
2
2
3
Back Cover
www.goedekers.com
Part No. 201471R3
April 2012
Advertisement
Table of Contents
Summary of Contents for Goedeker's Speed Queen awn432sp
-
Page 1: Installation Instructions
Installation Instructions for Topload Washers Inside........Washer Dimensions............Before You Start..............Installation................. Installer Checklist.............. Back Cover Date Purchased ________________ Model Number ________________ Serial Number _________________ Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) Part No. -
Page 2: Washer Dimensions
Washer Dimensions 28 in. (71.1 cm) 22.13 in. (56.2 cm) 0.4 in. 25.625 in. (65 cm) 26 in. (66 cm) (10.2 mm) *With leveling legs turned into base. TLW2075N Figure 1 Before You Start Parts Included An accessories bag has been shipped inside your Supplies washer. -
Page 3: Installation
Installation Step 2: Wipe Out Inside of Washtub Prior to first wash, use an all purpose cleaner, or a Step 1: Remove the Shipping Brace and detergent and water solution, and a damp cloth to Shipping Plug remove shipping dust from inside of washtub. Remove the shipping brace from under the lid. -
Page 4: Connecting Hoses
Step 3: Connect Fill Hoses NOTE: Water pressure under 20 pounds per square inch (138 kPa) will cause an extended fill time in the washer. WARNING Turn on the water faucets and flush the lines for Under certain conditions, hydrogen gas approximately two minutes to remove any foreign may be produced in a hot water system material that could clog the screens in the water... -
Page 5: Standpipe Installation
Step 4: Connect Drain Hose to Drain Receptacle COLD Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose from the retainer clamp. Install the drain hose into the drain receptacle (standpipe, wall or laundry tub) following the instructions below. -
Page 6: Laundry Tub Installation
Laundry Tub Installation: If standpipe is lower than 36 inches (91.44 cm), you must install No. 562P3 Siphon Break Kit. Refer to For this type of installation, the drain hose MUST be Figure 8. This kit is available (as optional equipment secured to the stationary tub to prevent hose from at extra cost) through an authorized dealer or parts disloding during use. -
Page 7: Step 5: Position And Level The Washer
Step 5: Position and Level the Washer Position washer so it has sufficient clearance for installation and servicing. Place washer in position on a clean, dry and reasonably firm floor. Installing the washer on any type of carpeting is not recommended. For easier access to leveling legs, prop up washer with a wooden block. - Page 8 Step 6: Plug in the Washer When plugging in the washer: • DO NOT overload circuits. Washer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-Prong grounding plug. • DO NOT use an extension cord. Refer to serial plate for specific electrical •...
-
Page 9: Grounding Information
Grounding Information Step 7: Add Water to the Washer The washer must be grounded. In the event of To prevent damage to pump, do not run washer before malfunction or breakdown, grounding will reduce the adding at least one quart water to the tub. If the washer risk of electric shock by providing a path of least is run before any water is added, the pump seal may resistance for electric current. -
Page 10: Step 8: Check Lid Switch
Step 8: Check Lid Switch Washer should stop agitating and spinning when lid is opened. W376IE0A W376I Figure 15 Step 9: Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly. - Page 11 www.goedekers.com...
-
Page 12: Installer Checklist
Installer Checklist Fast Track for Installing the Washer (Refer to the manual for more detailed information) • Remove the • Position and Level Shipping Brace and the Washer. LEVEL Shipping Plug. D255I D255I CHECK CHECK W316I W316I TLW1975N • Wipe Out Inside of Washtub. •...