Summary of Contents for TAGnology SmaFinger
- Page 1 TAGnology RFID GmbH | Grazer Vorstadt 142 | 8570 Voitsberg | AUSTRIA phone: +43 (0)3142/28 9 28-10 | fax: +43 (0)3142/28 9 28-20 | office@tagnology.com www.tagnology.com ® SmaFinger Mifare Configurable Sector Reader User’s Manual REV.A October 26, 2006...
- Page 2 On the aspect of personal privacy issue, SmaFinger supply the high secure of protection on privacy concern due to every fingerprint is stored on a card. Also the reader itself supports Mifare MAD1/MAD2 format make user end be able to issue their customized ID cards.
- Page 3 Mifare Application Directory (MAD) Support: SmaFinger support the MAD format card, the MAD (mifare® application directory) standard proposes the introduction of common data structures for card application directory entries. SmaFinger reader should take advantage of this feature using those sector pointers instead of physical sector number.
- Page 4 Data Type is fixed with 11b which meets "any other data" type of "Card Holder information" as MAD standard. And data length is including the data with ending zero "0", so the number of data byte sent by SmaFinger is equal to data length with one less for RS232 output.
- Page 5 To configure the SmaFinger reader you need connect the reader to the Reader-Kit first as below: Reader-KIT ORANGE BLACK WHITE WAS-T0029 YELLOW BLUE GREEN BROWN " " " " The above housing is for reference only 9VDC Note: Reader-Kit is a test connection kit for SmaFinger configuration use. It is an optional item for purchasing.
- Page 6 (1K Card Sector: 0~15, 4K Card Sector:0~39). For the Non-MAD application, user can freely define the Sector. App Key (KEY_A): (Default=FFFFFFFFFFFF) App Key must be the same as the KEY_A of the card issued. This means SmaFinger only can read the sector data on the card with the same KEY_A. Encrypt: (Default=None) Fraud prevention, Select Encrypt Mode (None, Encrypt 1, Encrypt 2, Encrypt 3, Encrypt 4, Encrypt 5) to protected your card data.
- Page 7 PROMAG SmaFinger REV .A Used Card (Not issued by "Mifare Card Issuer") You have to indicate the data position in the card, when the card is not issued by "Mifare Card Issuer" software. And you must set the "Offset" (Max 255, and base from zero) form the beginning of sector and set your data "Length"...
- Page 8 SmaFinger Reader ID for multi link application. (ID: 0~99). Interface : (Default=Wiegand) SmaFinger can be set as Wiegand , RS232 or ABA-TK2 output. Read Mode: (Default=Card Data Only) a. Card Data Only: Read card sector data only; If any error (ex. mifare key error), reader will show "Card Invalid"...
- Page 9 PROMAG SmaFinger REV.A 3. LED / Buzzer Settings New SmaFinger support the LED/Alarm Configuration. Setting the LED/Buzzer to indicate the system status for end-user. Enable RS232 Command Set Control: (For 19200,n,8,1 Only) RS232 LED/Buzzer command set frame as below: NUMBER (0~9)
- Page 10 Brown wire = Inactive ( or Card Is invalid): Show LED color and beeps to indicate the end-user when brown wire = Inactive, or card was failed by SmaFinger reader. Brown wire = Active: Show LED color and beeps to indicate the end-user that brown wire = Active signal from Host.
- Page 11 PROMAG SmaFinger REV.A 4. Wiegand Setting: Number of Bit s is to set the Wiegand output type you want to meet your Host (or Terminal). It can be 26 to 128 (Default=26). Include Reader ID is to set the Wiegand output data to include Reader ID when it is enabled.
- Page 12 PROMAG SmaFinger REV.A 5. ABA-TK2 Settings Number Of Digital: Set number of digital codes for TK2 output. (Default=10) Add Reader ID: Add Reader ID into TK2 data. (Default=Disable) Sequence: Set the TK2 data sequence. (Default=MSB First) Data Conversion: Select card data format to convert , a.
- Page 13 Digital Code (MSB) Remark: SmaFinger all configuration items are write only, so any users can not read the configuration items from SmaFinger to get the App Key, that is very important to protect your App Key and all configuration items.
- Page 14 ® 3. Get an issued mifare card to put on SmaFinger reader to be read and see the output data on the window of "SmaFinger Output Test". Wiegand 34 bits output data with standard bit sequence, example as below: (If "Bit Sequence" is standard, Reverse will detect a wrong with parity error.)
- Page 15 Operating Temp. 0~50 degree C Humidity 10~90% Humidity Dimension H13.00mm x W54.00mm x D43.00mm Note: 1. Mifare Class: Mifare Standard 1K/4K. ® 2. SmaFinger RF distance can reach up to 50mm with MFA01 (Mifare Standard 1K Card) of GIGA-TMS INC.
- Page 16 The reader places data as asynchronous low-going pulses on the Data 1 or Data 0 lines to transmit the data stream to Host. The Data 1 and Data 0 pulses will allowable pulse width times and pulse interval times for the SmaFinger reader. Data 1 Signal...
- Page 17 PROMAG SmaFinger REV.A ANNEX C. ABA TK2 Interface The timing for Card Present, Clock (Strobe) and Data , example as below: /CARD PRESENT Leading Zero Data Trailing Zero /DATA /STROBE (CLOCK) 0 . . . 0 STROBE Width Approximately 25~50% Of Bit Time...
- Page 18 PROMAG SmaFinger REV.A ANNEX D. RS232 Interface Connect the RS232 wires, example as below: HOST/Terminal 9~12VD (Red) SmaFinger TXD (Yellow) GND (Black) Optional: External LED/Buzzer Control (Brown)
- Page 19 REV.A ANNEX E. External LED/Buzzer Control SmaFinger supports the external LED/Buzzer control for T erminal (or Host) to prompt end-user the card data is invalid or valid. Use Brown wire to control the LED/Buzzer of SmaFinger Examples as below: (Active High)
- Page 20 WALL WALL L-shape screw cover plate Remark: SmaFinger is not designed for outdoor usage. Avoid the damage from sunshine or rains. To keep SmaFinger in good performance, it is recommended to have regular maintenance and clearance of the physical reader.
- Page 21 RS232 Cable for Reader Kit Power Adaptor DC Power Adaptor for Reader Kit PCR310U SmaFinger Card Issue Programmer DISK5288 SmaFinger Card Issue and Utility Software User Card x 3 Mifare Standard 1K Card 3pcs SF500-00 SF500-00 SF500 Configurable Reader SF500P-00...
- Page 22 User Card x 3 Mifare Standard 1K Card 3pcs SF600-00 SF600-00 SF600 Configurable Reader SF600P-00 SF600P-00 SF600 Fingerprint USB Programmer DISK5288 SmaFinger Card Issue and Utility Software PCR310U-40 PCR310U SmaFinger Card Issue Programmer DISK5288 SmaFinger Card Issue and Utility Software ® MFA01 MFA01...
- Page 23 SmaFinger REV.A ANNEX I. WebISP - Firmware Upgrade Utility SmaFinger also supports the ISP (In-System Program) function to upgrade the reader’s firmware. Install the WebISP (include in CD-ROM) in your Windows System first (It may need to reboot your system) and follow the steps as below: (First of all, you need to connect...
- Page 24 PROMAG SmaFinger REV.A Step 4: Wait for the updating to finish. And repeat step 2 to update other readers or programmers. Update finished Step 5: Check "Upgrade & Update Files" list to download the new and related software or utility to meet the updated firmware.
- Page 25 PROMAG SmaFinger REV .A ANNEX J. History Rev A: October 26, 2006 Initial SmfFinger Configurable Sector Reader.
Need help?
Do you have a question about the SmaFinger and is the answer not in the manual?
Questions and answers