Page 1 VDR-208&216 USER MANUAL Digital Hard Disk Recorder Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation.
Page 3: Table Of Contents
Table of contents SYSTEM OVERVIEWS ............10 ..........................10 AFETY & O ...................... 13 OMPONENTS PTION 1.2.1 Components......................... 13 1.2.2 Options ..........................13 & ....................14 EATURES SPECIFICATIONS 1.3.1 Features ..........................14 1.3.2 Specifications ........................15 & ..................16 FUNCTION CONNECTIONS 1.4.1 Front view ...........................
Page 4 2.10.1. Recording types........................26 2.10.2. Recording modes......................... 26 2.11..........................26 LAYBACK 2.11.1. Press the Play button ......................26 1.4.2 Audio files........................... 26 2.12..........................26 EARCH 2.12.1. Search mode ........................26 2.12.2. Search method ........................26 2.13..........................27 ACKUP 2.13.1.
Page 5 3.6......................35 ECORD ETUP MENU 3.6.1. Resolution ........................... 35 3.2.2 Audio Sync..............................35 3.3.3. Channel number ..........................35 1.4.4 Quality..........................35 1.4.5 Frame rate..........................35 1.4.6 Record mode ........................36 3.6.2. Record Schedule Setup......................37 3.7......................38 VENT ETUP 3.7.1.
Page 6 3.7.9. Event Log ..........................48 3.8......................... 48 LAYBACK ETUP 3.8.1. Channel ..........................48 3.8.2. Starting Point........................49 3.8.3. Audio........................... 49 3.9......................49 ISPLAY ETUP SCREEN 3.10..................... 50 ETWORK ETUP SCREEN 3.10.1. DDNS setting ........................50 3.10.2. Remote Connection Login Password .................. 52 3.10.3.
Page 7 3.11.6.2. Write Mode ............................61 3.11.6.3. Forced Deletion........................... 61 3.11.6.4. Hard Disk............................62 3.11.7. Aux Port ..........................62 3.11.7.1. Active..............................63 3.11.7.2. Function .............................. 63 3.11.8. Factory Default........................63 3.11.9. Software Upgrade........................ 64 3.12..........................64 ACKUP 3.12.1. Backup Device ........................65 3.12.2.
Page 8 3.16.1.2. Screen of played back......................... 71 3.16.1.3. Control during play back........................71 3.16.2. Playback of still image ......................72 3.16.2.1. Method of playback ..........................72 3.16.2.2. Screen of playing back........................73 3.16.2.3. Control during Play back ........................73 3.16.3. Playback the backed up-image ....................
Page 9 4.7.17. Check the program version....................90 4.7.18. S/W upgrade of DVR ......................91 4.7.19. Program minimizing......................91 4.7.20. Close program ........................92 4.8........................... 92 LAYER 4.8.1. Screen and button ........................ 92 4.8.2. Search..........................93 4.8.2.1. Search option from video image & backup file................... 93 4.8.2.2.
Page 10 4.11................112 ONNECTION BY NTERNET XPLORER 4.11.1. Security setup ........................112 4.11.2. Download ActiveX control ....................112 4.11.3. Connection with DVR......................112 Fill the address of DVR up in the address window of Internet Explorer............112 4.11.4. Login ..........................112 4.11.5. Connected screen........................113 4.11.6. Search..........................114 4.11.7.
Page 11: System Overviews
All rights reserved. No part of this publication may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopy, recording, or any information storage and retrieval system, without prior permission. 1. SYSTEM OVERVIEWS 1.1 Safety To prevent fire or shock hazard, do not expose the unit to rain WARNING or moisture.
Page 12: Safety Instructions
Warning – If TIMEKEEPER NVRAM IC that is consist of RTC, SRAM, POWER-FAIL CONTROL CIRCUIT and BATTERY is replaced, the replacement is to be done by a trained technician with the same type of component. Caution -- Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 13 has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Page 14: Components & Option
1.2 Components & Option The following items are included with the UDR-208 or UDR-216. Please be certain that all items are included as soon as you open the box: 1.2.1 Components UDR-208/216 ( CD/RW as a basic specification) Power cable DSUB-15 connector for PTZ /AUX / ALARM Quick Manual Software CD (RAMS, Uni Player, Multi Viewer, Quick Installer and Operation Manual)
Page 15: Features & Specifications
1.3 Features & specifications 1.3.1 Features 8/16 channel Embedded Digital Video Recorder MPEG-2 compression Quad-plex mode for simultaneous recording, playback, backup, and networking Live remote viewing, on-the-fly recording, and control over the network Dynamic IP support (DHCP & PPPoE) Alarm triggered FTP and E-mail alert function Motion detection, Video loss, and sensor alarm function User defined setting for recording frame rate &...
Page 16: Specifications
1.3.2 Specifications Item UDR-208 UDR-216 UDR-208E UDR-216E Image System NTSC, PAL selectable Video Channel 8 CH 16 CH Multi-tasking Quad-plex Video Output 2 Ch Composite(BNC), 1Ch S-Video, 1 Ch Spot, VGA Video Compression MPEG-2 Recording Resolution NTSC : 640x240, 320x240 PAL : 640x288, 320x288 Recording Quality 4 Levels (Normal, Enhanced, Fine, Super Fine)
Page 17: Name, Function & Connections
1.4 Name, function & connections 1.4.1 Front view Description: 1. CD/RW * Easy backup by CD/RW is available. The cover of CD/RW shows an excellent design. 2. LED indicator POWER: Power Off status is indicated by a Red light and ON status is indicated by a Green light.
Page 18 MULT (UDR-208) - Selection of Screen Division for Live Viewing mode (8 screen, 4 screen division, ) - In order to go back to previous mode, user is required to push “MULT” button, after selecting a specific channel SEQ : Sequential view. - View all active channels sequentially.
Page 19 PTZ control sub menu, used to move camera; or used to adjust focus. DOWN: Used to move the cursor up; change possible values in the setup menu; under PTZ control sub menu, used to move camera; or used to adjust focus. LEFT: Used to change possible values in the setup menu.
Page 20: Rear Panel View
1.4.2 Rear panel view Description: 1. USB Connect USB flash drives for backing up stored video files. 2. ETHERNET Network terminal for 10Base-T (RJ-45) 3. PTZ/AUX/ALARM Terminal for PTZ, sensor, alarm, and AUX IN/OUT (DB-15 Male Connector) 4. VGA and SERIAL VGA : Terminal for VGA video output (DB-15 Male Connector) Serial terminal for RS-232C (PC) for console or quick installation (DB-9 Male Connector) 5.
Page 21: Remote Controller Function
1.4.3 Remote controller function ① POWER : button for power on/off. (DVR should be standby or on working) ② MUTE : button for voice off ( If it’s pressed again, voice on) ③ RECORD : button for forced recording (If it’s pressed again, recording stops) ④...
Page 22 Ex : to select Ch 7, press 7 button and OK button. ⑥ LOCK : Remocon Rock button. Same function as Lock button in the front panel. To unlock, press any button and input password. ⑦ SEARCH : button to search data in HDD. Press the button to enter, and repress for exit ⑧...
Page 23: Installation
1.5. INSTALLATION 1.5.1. Installation and connection AUX OUT Sensor 1 Camera 1 Network AUX IN RS-485 Sensor 2 Reciever Monitor Speak Camera 2 Alarm Sensor16 Camera16 1.5.1.1. Camera UDR-216 : The unit comes with 16 video IN and 16 video OUT for up to 16 cameras connection.
Page 24: Video Out
1.5.1.2. Video Out The unit has two composite video outputs, one S-video output, one VGA output. Also one spot output allows users to select specific channel for special monitoring. 1.5.1.3. Audio Use IN for a Line input and OUT for speaker output. 1.5.1.4.
Page 25: Network
N.O. (Normal Open) is disconnected from COM during normal status and connected to COM during alarm event. N.C (Normal Close) is connected from COM during normal status and disconnected to COM during alarm event. 1.4.3.1.4 Sensor 1~16 Users can connect up to four N.O./N.C. type sensors and configure them within Main Menu, Sensor Setting.
Page 26: Basic Operation Procedures
2. Basic operation procedures 2.5. Power On/Off 2.5.1. Power on Using either the keypad or the remote control, press the “Power” button. (Note: In case of power outage or rare instance of system failure, the DVR will reboot automatically) The Power LED light will turn from red to green when it has turned on properly. In a standby mode, the LED is red.
Page 27: Network Setting
2.9. Network setting There are three types of network setting for the DVR: Static, DHCP, or PPPoE. Please set the network type. (Network Setup in Main Menu) 2.10. Recording Select recording related parameters in the Record Setup in the main menu. 2.10.1.
Page 28: Backup
Search, & Backup HDD Search. A detailed search list will open. Press OK button to view the selected file. Use the Left/Right key to move page by page. The Up/Down key is used to move between items on the same page. 2.13.
Page 29: Uniplayer
list. After selecting the target DVR, enter “admin” for ID and “111111” for default password. This will enable you to access the DVR. 2.14.2. UniPlayer A viewer with functions for recording, capturing, & backing up files. 2.14.3. MultiViewer To monitor multiple DVR, both locally and remotely. 2.14.4.
Page 30: Main Setup Screen
3. Main Setup screen Figure 3-1 Main Setup screen 3.5. Camera Setup menu Figure 3-2 Camera setup screen...
Page 31: Channel Number
3.5.1. Channel number. A user can select targeted camera. After setting, this, live viewing picture will be changed to selected channel automatically. 3.5.2. Camera Name Edit Figure 3-3 Camera name edit screen User can edit camera name indicated button part of each channel. as explained paragraph 3.1.1.
Page 32: Camera Hide
3.5.3. Camera hide User can make the live screen appear or not by channel with this function. If user sets up “On” in this function, the live screen of the selected channel does not appear. In case of recording, the recording continues, although screen does not appear. 3.5.4.
Page 33: Ptz Setup
Figure 3-4 Confirmation box on Picture Setting Default 3.5.5. PTZ setup Figure 3-5 PTZ setup screen It sets PTZ protocol of targeted channel in the Camera Setup. (Please refer to paragraph 3.1.1 for channel selection) 3.5.5.1. Model Number Select the PTZ model or choose “NONE”.
Page 34: Ptz Id
3.5.5.2. PTZ ID Set the PTZ ID: 0 ~ 255 The PTZ ID must match the ID number that has been set by the PTZ Controller. Please verify the ID on the Controller first before setting the PTZ ID. 3.5.5.3. Reverse Control Without any further changing of cable connection, user can control PTZ controller by changing reverse direction of PTZ.
Page 35: Sequence Time
Figure 3-6 Additional PTZ Menu - Go to Preset : To move the Pan/Tilt drive to the position preset in Set Preset mode. Preset numbers are selected by Left/Right buttons and the Pan/Tilt drive moves to the preset position after pressing OK button. - Set Preset : To preset the position of the Pan/Tilt drive.
Page 36: Record Setup Menu
3.6. Record Setup menu Figure 3-6 Record setup screen 3.6.1. Resolution Resolution for NTSC is “320 x 240” or “640 x 240”. PAL is “320 x 288” or “640 x 288” selectable and selected resolution will be applicable to all channels simultaneously. 3.2.2 Audio Sync As audio input port is one channel available, user should synchronize audio signal with...
Page 37: Record Mode
1.4.6 Record mode User will choose recording mode channel by channel and selectable parameters and meaning are below. • Manual: Manual recording function that starts record and/or stop recording manually by pushing REC key on remote controller or on front key. •...
Page 38: Record Schedule Setup
3.6.2. Record Schedule Setup Figure 3-9 Recording schedule setting screen User can select to set recording schedule targeted date, time based week & 24Hours. Move the cursor to the desired position of time by pressing up/down key and set the recording mode at the desired position of time by pressing the OK button with referring to the Help Message per Record Mode on the right position.
Page 39: Event Setup Menu
3.7. Event Setup Menu Figure 3-10 Event Setup screen 3.7.1. Motion Detection Setting Figure 3-11 Motion Detecting Setup screen Sets up the motion detecting area and sensitivity.
Page 40: Channel
3.7.1.1. Channel Sets up the motion detecting area and sensitivity for each channel. 3.7.1.2. Sensitivity Sets up the motion detecting sensitivity. The lower the sensitivity gets the closer to the left the red bar gets. 3.7.1.3. Detection Zone Figure 3-12 Motion Detecting Area Setup screen Selects the motion detecting area.
Page 41: Sensor Setting
3.7.2. Sensor Setting Figure 3-13 Sensor Setting screen 3.7.2.1. Sensor Type N.O.: Normal Open. Operation mode for the installed sensor’s contact point is usually open in normal condition and changed from open to close at sensor’s detect event. N.C.: Normal Close. Operation mode for the installed sensor’s contact point is usually close in normal condition and changed from close to open at sensor’s detect event.
Page 42: Alarm Output
3.7.3. Alarm Output Figure 3-14 Alarm Output Setting: 3.7.3.1. Sensor Configure the alarm out on/off activated by the sensor. 3.7.3.2. Motion Configure the alarm out on/off triggered by the motion detection. 3.7.3.3. Relay Time Configure the alarm duration time. It can be set up from 1 second to 60 seconds in the unit of 5 seconds.
Page 43: Ftp Setting
3.7.5. FTP Setting Figure 3-15 FTP Setting Enables the unit to transmit an assigned FTP Length of Motion picture to an FTP Server over network when an event occurs. The event will be transmitted 15 seconds after the event occurs. 3.7.5.1.
Page 44: Password
3.7.5.2. Configure the FTP ID. The ID can contain maximum of 31 characters. Figure 3-16 FTP ID 3.7.5.3. Password Configure the FTP password. The password can contain maximum of 12 characters. Figure 3-17 FTP Password input...
Page 45: Target Path
3.7.5.4. Target Path Configure the path to transmit to an FTP server. The path can contain maximum of 31 characters. Figure 3-18 FTP Target Path 3.7.5.5. FTP Length of Image (second) Select FTP length of image by second (5 to 10 seconds are selectable) to transmit image files for selected seconds.
Page 46: Sensor
Figure 3-19 FTP Trigger Setting 3.7.6.1. Sensor Configure sensor events. 3.7.6.2. Motion Configure motion events. 3.7.7. E-Mail Address Setting Transmits the content of an event log periodically through e-mail. Configure up to four e-mail address to transmit under event status simultaneously. The e-mail address can contain maximum of 31 characters, and the event logs transmitted through e-mail will be deleted in the DVR unit.
Page 47: E-Mail Setting
Figure 3-20 E-Mail Address setting 3.7.8. E-Mail Setting Figure 3-21 E-Mail Setting 3.7.8.1. Send (Period) Configure the e-mail transmitting cycle. It does not transmit when it is set to NO. The setting time can be set up at the units of within 2 minutes after event, 30minutes, 1, 2, 5, 12, 24 hours.
Page 48: Prohibition Setting
3.7.8.2. Prohibition setting Set up prohibition time to transmit the e-mail. Users can enter prohibition time from the starting time and the ending time of transmitting the e-mail 3.7.8.3. SMTP Server IP address Configure the IP address of the SMTP server to transmit the e-mail. If you do not know your SMTP server IP address then go to Command Prompt in Windows, then use ping and SMTP name address eg mail.unimo.co.kr as below to get your SMTP IP address.
Page 49: Event Log
3.7.9. Event Log Shows the event log of the selected channel. It can reset periodically by setting e-mail as described in paragraph 3.3.7. Figure 3-22 Event Log Display screen 3.8. Playback Setup Figure 3-23 Playback setup screen 3.8.1. Channel Designate the channel to be viewed when the “Replay” button is pressed.
Page 50: Starting Point
3.8.2. Starting Point This starting point configures the starting position when the “Replay” button is pressed. FIRST: This can search for and replay the oldest recorded images from the selected channel. LAST: This can search for and replay the latest recorded images from the selected channel. 3.8.3.
Page 51: Network Setup Screen
3.10. Network Setup screen Figure 3-25 Network Setup screen 3.10.1. DDNS setting Set up DDNS (Dynamic Domain Name System) server address & port number. Users can set up two DDNS server address and port. Figure 3-26 DDNS setup screen...
Page 52 Under DHCP or PPPoE configuration using IP Router, the DVR will receive an IP address periodically, and each time, the IP address can be different. Therefore, in order for users to access the DVR over the network, it must update its IP address to the DDNS Server. Under IP router configuration, IP of DVR must be setup as static IP address and it must update its IP address to the DDNS server.
Page 53: Remote Connection Login Password
3.10.2. Remote Connection Login Password There are two levels of access that can be set up in the RAMS program. Admin (Highest), User (Normal) By default, the password is 111111 when the software is first installed. Users can use any numeric number from 0~4, combined 6 units. Figure 3-27 Remote Connection Login Password screen 3.10.3.
Page 54: Static
3.10.4. Static Figure 3-28 Static Network setting 3.10.4.1. DDNS On/off 3.10.4.2. Port Configure the Port number to be used to connect to the UDR-204 system using RAMS (Remote Access & Monitoring System). The default Port number is port 80. Change easily by using Jog/shuttle equipped in front panel.
Page 55: Port
3.6.5 DHCP Figure 3-29 DHCP setup screen 3.6.5.1 Port Please refer to paragraph 3.6.4.1for Port setting of Static/ DHCP/ PPPoE) 1.4.6 PPPoE Figure 3-30 PPPoE setting...
Page 56: Port
3.10.4.6. Port Please refer to the port setting in paragraph 3.6.4. 3.10.4.7. ID Type in your user ID for the ADSL account (PPPoE). The password can contain maximum of 31 characters. Figure 3-31 ID input screen 3.10.4.8. Password Type in your user Password for the ADSL account (PPPoE), The password can contain maximum of 12 characters.
Page 57: Changing The Network Configuration
3.10.5. Changing the Network configuration If users want to change network type of UDR-204, users must reboot the system. User can restart the new network mode setting after entering ‘yes’ key button. Figure 3-33 Changing the Network setting screen 3.11. System Setup screen Figure 3-34 System Setup screen 3.11.1.
Page 58: System Password
Figure 3-35 DVR name screen Using the arrow, type in the DVR name. Click “OK” when finished. 3.11.2. System Password Figure 3-36 System password set up Set up part for system password, related function and application.
Page 59: Password Setting
This is a part of installation, actual system password, related function and password application. 3.11.2.1. Password Setting To change system password: First, type-in the current password, confirm. Then if it is correct, type-in the new password twice. If they match, the password has been changed. Users can use any numeric number from 0~8, combined 6 units.
Page 60: Auto Key Lock
3.11.2.3. Auto Key Lock Possible Setting time is every 30sec, 1 min, 3min, 5min, 10 minutes. If users choose setting time among them, auto key lock function will start exactly after the setting time and lock key Users can access system operation after type icon will be displayed at the bottom of window.
Page 61: Buzzer
1.4.6.1.2 Start date (m/d) Set up start day in Day Light Saving Time mode. 1.4.6.1.3 End date (m/d) Set up end date in Day Light Saving Time mode. 3.11.4. Buzzer Users can turn the buzzer On/Off depending on the situations. Usable situation is Sensor, Motion, &...
Page 62: The Number Of Hdd
Figure 3-40 HDD Setup image 3.11.6.1. The number of HDD Show the HDD quantity that is built –in. 3.11.6.2. Write Mode Set up writing type in recording. Types are ‘Once’ and ’Overwrite’. If set up by ‘Once’, HDD can record until the Full state. If set by ‘Overwrite’, HDD will record continuously by start overwrite oldest data.
Page 63: Hard Disk
3.11.6.4. Hard Disk 1.4.6.1.4 Capacity Indicate the used part and total capacity of Internal HDD. Used part of HDD (GB) / Full capacity of HDD (GB) 1.4.6.1.5 Format This is function for internal HDD formatting and you must reboot the system after this instruction.
Page 64: Active
3.11.7.1. Active Set up Active state. Low/High will be different depend on machine.. 3.11.7.2. Function The following list contains a brief description of each function. 1.4.6.1.6 Direction : IN • UNUSED: Do not use the AUX port. • ALARM RESET IN: Pause alarm or buzzer when event occurred •...
Page 65: Software Upgrade
3.11.9. Software Upgrade Users can upgrade the software of Ramdisk and Kernel using the USB flash drive (thumb drive) by the following steps. - Get the latest version of software (Ramdisk/Kernel) from distributor - Copy the downloaded files from the PC to the USB memory. - Connect the USB memory to the USB port.
Page 66: Backup Device
Figure 3-48 Backup screen 3.12.1. Backup Device Set up the device for backup. USB/ CD-RW are available 3.12.2. Start Time Input the start of backup date and time. 3.12.3. End Time Input the end of backup date and time. 3.12.4. Channel Choose the channel to backup.
Page 67: System Log
3.13. System Log It is for displaying major system events. The items that manage by Log are Video Loss, Power On, Power Off, Menu entry, HDD Full, failure of FTP transmission, failure of E-mail transmission Figure 3-48 System Log 3.14. System Information Figure 3-49 System Information...
Page 68: Video Type
3.14.1. Video type It shows that present Video type of System is NTSC or PAL. 3.14.2. H/W version It shows the H/W Version of system. 3.14.3. S/W version It shows the S/W Version of system 3.14.4. KERNEL version It shows the S/W Version of KERNEL. 3.14.5.
Page 69: Search By Time
3.15.1. Search by Time The recorded images are searched by Time, Channel, Event. UDR-204 saves lat searching condition so it automatically displayed last search condition under search mode. ** Screen where the condition of search will be input. Figure 3-51 Search by time 3.15.1.1.
Page 70: Example Of Search Result
• MOTION : The file recorded by MOTION is searched. • SENSOR : The file recorded by SENSOR is searched. 3.15.1.5. Example of Search Result Figure 3-52 Screen of result of search by time 3.15.2. Search of still image Still image is not searched by Time and Channel. If users press “search”...
Page 71: Search Of Back Up Hdd
Figure 3-53 Search Screen of Still Image 3.15.3. Search of back up HDD The images that were backed up manually or automatically can be searched by Time, Channel, Event. Figure 3-54 Screen for input data of HDD Search The method of input and search is the same as that of recorded file, as indicated in the paragraph 3.10.1.
Page 72: Screen Of Played Back
3.16.1.2. Screen of played back. Figure 3-55 Screen of playback 3.16.1.3. Control during play back 1.4.6.1.8 Stop of Play back If user needs to stop play back, user should press button “ STOP” in the remote controller of in the system, and play back stops and live screen is coming back. 1.4.6.1.9 Temporary Stop during Playback In order to stop temporarily playback, press button “...
Page 73: Playback Of Still Image
If user needs faster speed of playback, users press button “RIGHT” and speed is controlled. If user needs slower speed of playback, users press button “LEFT” and speed is controlled. 1.4.6.1.11 Change of Direction of Playback There’s forward and Backward directions. In order to change direction from Forward to Backward, user press the button “...
Page 74: Screen Of Playing Back
3.16.2.2. Screen of playing back Figure 3-56 Still Image of playing back 3.16.2.3. Control during Play back 1.4.6.1.14 Stop of play back To stop the playing back, User press button “STOP” or “ SEARCH”. Playback stops and screen of search list appears. 1.4.6.1.15 Next screen Press Button “RIGHT”...
Page 75: Miscellaneous Menu
The functions for Playback of backed up images, screen during playback, control during playback are same as those of Playback of Recorded images, as the paragraph 3.11.1 3.17. Miscellaneous Menu Figure 3-57 Miscellaneous Menu This menu is to use the five functions that are placed only on the remote control but on the keypad of the unit 3.17.1.
Page 76: Osd
Figure 3-58 Network Information 3.17.2. OSD Turns on/off the OSD (On Screen Display). It substitutes the OSD button on the remote control. 3.17.3. Audio Mute Turns on/off the audio. It substitutes button on the remote control. 3.17.4. HDD Displays the HDD information. It substitutes the HDD button on the remote control. 3.17.5.
Page 77: Udr-208/216 Client Program
4. UDR-208/216 Client program 4.5. Overview of UDR-208/216 RAMS (Remote Access & Monitoring System) is used to remotely access, monitor, and operate the DVR for real-time live viewing, playback, backup, on-the-fly recording, and control over the LAN/WAN. UniPlayer is a viewer with functions for recording, capturing, & backing up files. Multiviewer is to monitor multiple DVR QuickInstaller is a setup configuration template for quick &...
Page 78: Rams (Remote Access & Monitoring System)
4.7. RAMS (Remote Access & Monitoring System) 4.7.1. Screen and button < UDR-208> <UDR-216>...
Page 79: Connecting To Dvr
① Screen capture button, Video record button ② Screen display ③ Channel display button, Sound control button ④ If logo is clicked, program version window appears. ⑤ Time indicator ⑥ PC HDD information indicator ⑦ Live or Playback mode indicator ⑧...
Page 80: Uniplayer Link
① This box allows the user to select the IP address assigned to the selected unit. This is required for making a network connection. ② To create a new IP address & DVR selection, enter the DVR name, DVR address, and port number.
Page 81: Full-Screen Display
4.7.4. Full-screen display If you push this icon in the main menu, full screen form appears. If users press the key of ESC, you will return to the selected screen. OSD in the screen is same as that of DVR (Channel name, recording on/off, Motion icon, Sensor icon)
Page 82: Program Setup
4.7.5. Program setup If users click this button in the main window, window of program setup appears. ① Capture a still image and select a folder where the image is recorded ② Select the image of water mark to be input in the still image ③...
Page 83: Dvr Playback Search
=> DVR (live viewing) => DVR (Recording mode) 4.7.7. DVR playback search This button is used for playback search, playback, and backup functions for DVR and after logging in by admin.
Page 84: Dvr Playback Search
① Enter search time from start time to end time ② Check if user want to search event condition ③ Select targeted channel for search ④ Close DVR playback search ⑤ Start to search by selected searching condition ⑥ Previous research result will appears 4.7.8.
Page 85 ① DVR search files will appear recording start/end time, channel, and event information included ② Button for staring of backup. With pushing selected channel, start to playback. Start to playback after pushing selected channel,. If do double click selected files, it starts to playback.
Page 86 ① Change present mode to playback mode ② Display playback picture derived from DVR system ③ Button for reverse playback, pause, still, reverse phase, forward phase, slow, fast, previous search, next search ④ Comeback playback mode to Live viewing mode Reverse playback button Playback button Temporarily pause button...
Page 87: Dvr Backup
Play stored files quickly. User can control by clicking this button 4.7.9. DVR backup ① DVR search files will appear recording start/end time, channel, and event information included ② Indicator backup progress at backup ③ Button for staring of backup. With pushing selected channel, start to backup ④...
Page 88: Dvr Setting
4.7.10. DVR Setting This button is for linking into quick installation program, which is used to manage setting parameter of DVR easily. It can be activated after logging in by admin. The setting parameter of DVR are displayed. 4.7.11. Still image Capture Yon can save playing image such as live viewing image, DVR playback image, into still image by capture.
Page 89: Watermark Insertion
① Select check box in order to insert watermark into still image capture ② Save still image as user defined default file name if chosen ③ Save still image as user selected new file name if chosen ④ Insert keyword to user easy searching ⑤...
Page 90: Pan/Tilt, Zoom/Focus
① Select the targeted channel changed recording time. Among this mode, Quad mean that timing choice for recording button on main menu ② Continuous recording until clients stop recording mode ③ Continuous recording until targeted minutes. Of course, it stopped manually by users ④...
Page 91: Check The Program Version
White: remaining par of HDD. Detailed HDD information will be activated on pushing this icon. ① Select hard disk ② It shows total capacity of HDD ③ It shows the used capacity of HDD used ④ It shows the capacity of HDD to be used ⑤...
Page 92: S/W Upgrade Of Dvr
4.7.18. S/W upgrade of DVR S/W upgrade window is activated on pushing S/W upgrade button in the program version check screen ① : Select targeted files to upgrade ② : Select targeted files saved in local PC ③ : Enter targeted DVR information such as DVR address, Port, user, and password (admin only) ④...
Page 93: Close Program
4.7.20. Close program Closed Multiviewer program 4.8. UniPlayer 4.8.1. Screen and button ① Button per channel (Capture, Print, D-Zoom) ② Playback picture ③ Indicator for playback progress rate ④ Reverse playback, playback, still, pause, reverse phase, forward phase, slow, fast ⑤...
Page 94: Search
4.8.2. Search Users access to search files after push this icon. As files are default mode, without knowing of files, users can access it. 4.8.2.1. Search option from video image & backup file ① Select whether recording files at RAMS, Multiviewer or backup files ②...
Page 95 => If there is nothing to special condition for searching, all files saved in recording folder will be displayed on search window after searched. => Search window after selected channel number 1 as search option.
Page 96: Search Option For Still Image
4.8.2.2. Search option for still image ① Enter targeted recording date for search ② Enter targeted DVR name for search ③ Enter targeted channel ④ Enter keyword to classification to list ⑤ Start to search accordingly ⑥ Close search option window =>...
Page 97: Searching By Directory
=> Search window after selected channel number 1 & selected date (Sept. 30, 2005) as search option. 4.8.3. Searching by directory You can use it when you know the directory has AVI file or still image file. It will be set up default directory at first.
Page 98: Still Image Capture
=> AVI file Playing screen by searching scene 4.8.4. Still Image Capture Save replaying images into still image by capture. Besides users can capture image by push capture button for each channel or push capture button at the foot of a screen. Still image will be saved in a path of which is established in RAMS’s setup section screen ①...
Page 99: Input Water Mark
④ Insert keyword to user easy searching ⑤ Close still image capture window ⑥ Print still image capture file ⑦ Save still image. The destination of recording is assigned at still image recording folder through setup menu among RAMS program 4.8.5.
Page 100: Water Mark Drawing
4.8.8. Water mark drawing When still image is display, if push this button watermark will be drawn. If you find other color except black, white, blue color, image file must get damaged. Push this button one more time, reverts to original image state. =>...
Page 101: Panorama
Watermark viewing screen. If you find other color except black, white, blue color, image file must get damaged. 4.8.9. Panorama You can see the panorama screen when you push this button while file playing. (Button will change into like this button. .
Page 102 => Screen in panorama mode. => Image when click one screen in panorama mode.
Page 103: Check The Program Version
4.8.10. Check the program version. Click Unimo logo to confirm version. 4.8.11. Close Program Close UniPlayer program 4.9. MultiViewer 4.9.1. Program login ① Insert program password. ② If inserted password is right, multiviewer runs. ③ Close program ④ Modify program password.
Page 104 ① After inserting current password, change password, & confirm password accordingly, changes program pass. ② Closing window without changing. Return to login window...
Page 105: Screen And Button
4.9.2. Screen and Button ① ICON for Event (Motion, Sensor): If an Event is activated, => => color of icons change. ② BUTTON for channel (Connect/Disconnect, Capture, Record) ③ Channel SCREEN ③ Click on UNIMO logo to check the version of program ⑤...
Page 106: Dvr List Management & Connection
4.9.3. DVR LIST management & connection If users click this button in the main screen, DVR List management & connection window appear. ① DVR List that user recorded, appears. ② Input DVR name, IP address, domain name, port ③ Input id name ④...
Page 107: Camera On/Off
=> Connected screen => If connection is impossible, it displays error defectives on screen. 4.9.4. Camera On/Off In order to connect to DVR in the main screen, please click button, and select DVR, and log in. After connection, please click one more time , and DVR is disconnected.
Page 108: Full Screen
4.9.5. Full Screen Click the Full Screen button to open a screen in full view. Press ESC to return. 4.9.6. Program Setup Click to launch Setup.
Page 109: Link With Uniplayer
① Indicates the file location of the captured still Image ② Indicates the file location of the watermark image to be inserted in the still image ③ Select language ④ Set up whether alarm occurrence is on or off when motion detection or sensor icon activated.
Page 110: Confirmation Of Version Of Program
① Select HDD disk ② It shows total capacity of HDD ③ It shows the used capacity of HDD ④ It shows the free capacity of HDD ⑤ It shows both the used capacity of HDD and free space ⑥ Click to close the screen 4.9.10.
Page 111: Quick Installer
4.10. Quick Installer 4.10.1. Select model Clicks to select DVR model name and video type in order to set system parameters. 4.10.2. System parameter setting * Right parts on System parameter setting window is same form as Main menu used in DVR system.
Page 112: Communication Over Network Or Serial Port
4. System parameter-> Write parameters to DVR: Transfer to save setting parameters of DVR. 5. System parameter->Default value setting: Initialize parameters values. 6. Communication->Network: Communicate data through network. 7. Communication->Serial: Communicate data through serial port (Setting preferable ComPort) 8. Language: Click to select preferable language 9.
Page 113: Connection By Internet Explorer
4.11. Connection by Internet Explorer 4.11.1. Security setup Setting up minimum level of security in the Internet Option of Internet Explorer. 4.11.2. Download ActiveX control In order to download ActiveX control, press “confirmation” button, when the message Appears, and download in the PC. (If “cancel”...
Page 114: Connected Screen
fill network password of DVR and press “OK” button, same as Rams program. 4.11.5. Connected screen 1. In the lower part of screen, there are buttons button to select the screen division & button to search the moving picture.. 2. In the right part of screen, there is a button to control PTZ. PTZ control is available when one screen is selected, In order to select one screen, double click the required channel.
Page 115: Search
4.11.6. Search Same function as search of DVR playback search (4.3.7). Please refer to the article 4.3.7. 4.11.7. Playback This is the screen when it’s playback.. Playback control button in the right parts has same...
Page 116: Appendix
function as DVR playback in RAMS. Please refer to the article 4.3.8. (DVR manual) 5. Appendix 5.5. Installing HDD 5.5.1. Installing single hard disk drive 2 HDD can be installed for UDR-208/216. In case that 1 HDD is installed, HDD should be set to “MASTER” or “SINGLE” mode. In case that 2 HDD are installed, one HDD should be set to “MASTER”...
Page 117 Right picture shows that HDD is set to CS ( Cable Select). EX :In cases of assembling 1 HDD Assemble as the above picture ( Brackets are used for any direction) In case of 1 HDD, in general HDD is used to MASTER/SINGLE mode ( Screw M3.5 x 5L is used, which included) Ex : In case of assembling 2 HDD Please make sure that one HDD is set to MASTER/SINGLE, the other is set to...
Page 118 The above pictures show that the assembled HDD is connected to DVR. Upper picture is for 1 HDD, lower picture is for 2 HDD. The circled part is HDD connector. Please make sure that direction is correct.
Page 119: Terminal Information
The picture shows the connection of 80 pin HDD Cable. In the circle, small triangle indicate the position of pin # 1. ( The triangle should be located on the red line of 80 pin HDD cable) 5.6. Terminal Information 5.6.1.
Page 120: Dsub-15P (Ptz / Aux / Alarm / Sensor)
5.6.2. DSUB-15P (PTZ / AUX / ALARM / SENSOR) Name Description Name Description RS-485+ RS-485 Transmit Data + Alarm Out Alarm Out (NO) RS-485- RS-485 Transmit Data - Alarm Out Alarm Out (COM) AUX1 Auxiliary In Port Alarm Out Alarm Out (NC) (RSI, ARI, RONOFFI)* AUX2 Sensor1...
Page 122: Factory Default Value
5.7. Factory Default Value 5.7.1. Main Menu Menu Default Vale Remarks Main Sub Menu1 Sub Menu 2 Sub Menu 3 Menu Camera Channel Channel No CH-1~CH-16 Setup Camera Name CH-1~CH-16 Covert Picture Setting Contrast 9 Level Max. 16 Levels Brightness 9 Level 9 Level PTZ setup...
Page 123 Channel Link NONE CH1~CH16 Alarm In/Output Sensor Sensor 1 Alarm Output Motion CH 1 Alarm Output Relay time 0 sec Post-Alarm Record 10 sec 10, 20, 20, 40, 50, 60 sec FTP Setting FTP Server 0.0.0.0 Address anonymous Password Blank Target Path FTP Length of 5 sec...
Page 124 DHCP Port PPPoE Port Registered ID Password 111111 Registered PW DNS IP 0.0.0.0 System DVR name 16CH DVR Setup System password Password setting ****** 111111 Password Apply Record Stop Menu enter System off Auto Key Lock Time / Date Time Setup (h/m/s) Current Time Date Setup Current Date...
Page 125: Search Menu
Audio Support Depends software version Language English French Depends German Japanese software Korean Spanish version 5.7.2. Search Menu Menu Default Value Remarks Main Sub menu1 Sub menu2 Sub menu3 menu Date : Date of Yesterday Start Time Time : Current Time Date : Date of Today Search by Time End Time...
Page 126: Protocol
5.8. Protocol 5.8.1. Code table Protocol Description Remarks kmute Audio Mute krec Record khdd HDD Information knet Network user information klog Log Display kinfo System Information knum1 Number 1 knum2 Number 2 knum3 Number 3 knum4 Number 4 knum5 Number 5 knum6 Number 6 knum7...
Page 127: Usage
Shuttle left 1Step Shuttle left 2Step Shuttle left 3Step Shuttle left 4Step Shuttle left 5Step Shuttle left 6Step Shuttle left 7Step kjleft Jog left kjright Jog right kpower Power 5.8.2. Usage - System protocol to control UDR-204 from remote client software installed in PC or remote controller. - It maps button function of remote controller with front key in the front panel of UDR-204.
Page 128: Hdd Recording Time Table
5.9. HDD recording time table (Based on recording mode, Resolution, picture Quality, FPS) Frame Recording time per HDD capacity (HR) Resolution Quality Rate System 80GB 120GB 160GB 200GB 300GB (fps/CH) 43.80 65.70 87.60 109.50 164.25 Super 80.91 121.36 161.82 202.27 303.41 Fine 291.27...
Page 129 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Brussels Office Planet II - Unit E...

This manual is also suitable for:

Vdr-216

Vicon VDR-208 User Manual

1 System Overviews

Installation

2 Basic Operation Procedures

3 Main Setup Screen

4 Udr-208/216 Client Program

5 Appendix

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Vicon VDR-208

Summary of Contents for Vicon VDR-208

This manual is also suitable for:

Table of Contents