Specifications; Fcc Information - Radio Shack 43-325 User Manual

telephone base and the cordless handset by radio waves, so there
is a possibility that the cordless telephone conversations could be
intercepted by radio receiving equipment within range of the cordless
handset. For this reason, you should not think of cordless telephone
conversations as being as private as those on corded telephones.
• Electrical power: The telephone base of this cordless telephone must
be connected to a working electrical outlet. The electrical outlet should
not be controlled by a wall switch. Calls cannot be made from the
cordless handset if the telephone base is unplugged or switched off, or
if the electrical power is interrupted.
• Potential TV interference: Some cordless telephones operate at
frequencies that may cause interference to televisions and VCRs. To
minimize or prevent such interference, do not place the telephone base
of the cordless telephone near or on top of a TV or VCR. If interference
is experienced, moving the cordless telephone farther away from the TV
or VCR often reduces or eliminates the interference.
• Rechargeable batteries: Exercise care in handling batteries in order not
to create a short circuit with conducting material such as rings, bracelets,
and keys. The battery or conductor may overheat and cause harm.
Observe proper polarity between the battery and the battery charger.
• Nickel-metal hydride rechargeable batteries: Dispose of these
batteries in a safe manner. Do not burn or puncture the battery. Like
other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.

Specifications

Frequency control ....................................................... Crystal controlled PLL synthesizer
Transmit frequency
Handset: ......................................................................................... 1921.536-1928.448 MHz
Telephone base: ............................................................................ 1921.536-1928.448 MHz
Channels .............................................................................................................................. 5
Size
Handset: ............................................. 6.35 × 1.87 × 1.24 in (161.50 × 47.50 × 31.50 mm )
Telephone base: ............................... 5.38 × 4.70 × 3.28 in (137.00 × 119.50 × 83.50 mm)
Charger: ................................................. 3.70 × 3.20 × 1.91 in (94.00 × 81.50 × 48.50 mm)
Weight
Handset: .................................................................... 4.54 oz (128.60g) (including battery)
Telephone base: ....................................................................................... 5.88 oz (166.80 g)
Charger: ....................................................................................................... 2.43 oz (69.00 g)
Power requirements
Handset: ................................................................................ 2.4V 500mAh Ni-MH battery
Telephone base: .........................................................................................6V AC @ 300mA
44
Charger: .......................................................................................................6V AC @ 300mA
Memory
Handset directory: ..............................................................................50 memory locations
Handset call log: ................................................................................50 memory locations

FCC Information

This equipment has been tested and found to comply with the requirements for a
Class B digital device under Part 15 of the Federal Communications Commission (FCC)
rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult your local RadioShack store or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by RadioShack may cause
interference and void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation. Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested and found to comply
with the FCC criteria. The handset may be safely held against the ear of the user. The
telephone base shall be installed and used such that parts of the user's body other than
the hands are maintained at a distance of approximately 20 cm (8 inches) or more.
This equipment complies with Part 68 of the FCC rules and with technical requirements
adopted by the Administrative Council for Terminal Attachments (ACTA). The label
on the back or bottom of this equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your
local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJ11 jack should normally be used for connecting to
a single line and an RJ14 jack for two lines. See Installation Instructions in the user's
manual.
up to 30 digits and 15 characters
up to 24 digits and 15 characters
45