Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Azkoyen M02
- Page 1 Technical information: M02 / CAPRICCIO M02 / CAPRICCIO 10087 UK 09 - 2004...
- Page 2 Technical information: M02 / CAPRICCIO I N D E X INTRODUCTION 1.1. DEFINITIONS 1.2. PRINCIPLE TECHNICAL CHARACTERISTICS DESCRIPTION OF COMPONENTS INSTALLATION AND SWITCHING ON 3.1. UNPACKING 3.2. INSTALLATION AND SWITCHING ON WORKING CONDITIONS AND NORMS CLEANING AND MAINTENANCE DIMENSIONS 10087 UK...
- Page 3 This Technical Manual describes the technical characteristics that correspond to the automatic coffee grinders in the MO2 / CAPRICCIO range. The M02 / CAPRICCIO range has two models: M02 / CAPRICCIO with a display M02 / CAPRICCIO with no display Both models in this range can be manufactured in different colours.
- Page 4 The grinding teeth are of very high quality. Their diameter is 64 mm. All models in the range use 230 Vac. The power consumption of all the models in the M02 / CAPRICCIO range is 525 w. 10087 UK 09 - 2004...
-
Page 5: Description Of Components
Technical information: M02 / CAPRICCIO DESCRIPTION OF COMPONENTS Coffee bean hopper The hopper is made of smoked transparent polycarbonate and the cover of ABS; it has a maximum capacity of 1500 g of coffee beans. The hopper has a gate that can be closed manually. It is used to block the exit of coffee beans when it is removed from the grinder. - Page 6 Technical information: M02 / CAPRICCIO Tajadera abierta Tajadera cerrada Coffee identification label The hopper has a window where a label can be placed that identifies the type, variety or quality of the coffee beans used in the hopper. It can also be used for publicity.
-
Page 7: Programming Button
Technical information: M02 / CAPRICCIO Only the third and subsequent services of ground coffee should be used after regulating the new “grind point” Display El display is comprised of four 7-segment displays that can show four digits. Programming button Pressing on this button gives access to the deferent programming functions on these coffee grinders. -
Page 8: On/Off Button
Technical information: M02 / CAPRICCIO ON/OFF button On the grinders that have a display, this button is used to switch the grinder on and off. 10. Programming button This button is only on the grinders that do not have a display. It is used to go from “working mode”... -
Page 9: Mains Switch
Technical information: M02 / CAPRICCIO 14. Mains switch This is used to switch the grinder on or off. It connects and disconnects both phases of the mains. 15. Mains flex It is 1500 mm long. The plug is Schucco. 16. Housing It is divided into two pieces: the front made of aluminium and the casing made of sheet metal. - Page 10 Technical information: M02 / CAPRICCIO Voltage 230 Vac Power 525 w Diameter of grinders 64 mm Grinding teeth distance “grind point” 0,006 mm Life of DITTING grinders ≈ 50,000 coffees Life of CATALÁ grinders ≈ 25,000 coffees The useful life of the grinders is reduced if the coffee mix has torrefacto coffee (caramelised coffee) When the grinding teeth are changed, to adjust the “grind point”...
-
Page 11: Circuit Board
Technical information: M02 / CAPRICCIO A. Blocking spring B. Notch C. Regulating disk 20. Circuit board This element controls all the functions of the grinder. Connection of the motor and the transformer Connection of the main switch Connection of the gate motors and the dosage element... - Page 12 Technical information: M02 / CAPRICCIO The factory default programming on leaving the factory is: Single coffee dose 8 g – 1.9 s Double coffee dose 14 g – 3.35 s Dosage correction factor No correction factor Grinding mode Pre grind...
- Page 13 Technical information: M02 / CAPRICCIO Voltage 24 Vdc Maximum power with load 425 mA R.P.M. with load 11.000 Working temperature -10ºC a +60ªC Maximum relative humidity (without 95 % condensation) When the motor is activated to change position, it receives 24 Vdc for 50 ms.
- Page 14 Technical information: M02 / CAPRICCIO • Separate the cover from the distributor. • Disconnect the wiring from the butterfly motor. • Remove the dosage element. 10087 UK 09 - 2004...
-
Page 15: Installation And Switching On
Technical information: M02 / CAPRICCIO INSTALLATION AND SWITCHING ON 3.1. Unpacking Proceed with unpacking the grinder when you are at the site location. Dispose of the packing material according to current legislation. 3.2. INSTALLATION AND SWITCHING ON Place the grinder in the chosen position and plug it in to a socket that supplies 230 Vac, a minimum of 550 w and is earthed. - Page 16 Technical information: M02 / CAPRICCIO WORKING CONDITIONS AND NORMS The optimum working conditions of this equipment is achieved by fulfilling the following requirements: Temperatures: Storage: -25 to + 70ºC. Working: +5 to +50º C. Norms that are met: Electromagnetic compatibility: •...
-
Page 17: Cleaning And Maintenance
Technical information: M02 / CAPRICCIO CLEANING AND MAINTENANCE Cleaning is an important part of the maintenance in order to guarantee an adequate level of hygiene of the grinder. Maintenance is an important factor to achieve optimum performance from the equipment. - Page 18 Technical information: M02 / CAPRICCIO DIMENSIONS The weights are given in kilograms and the measurements in millimetres Model Weight Height A Height B Width Depth M02 / CAPRICCIO with display CAPRICCIO with display 10087 UK 09 - 2004...
- Page 19 Technical information: M02 / CAPRICCIO Brands of the AZKOYEN AZKOYEN MEDIOS DE PAGO S.A. 10087 UK 09 - 2004...