Subscribe to Our Youtube Channel
Summary of Contents for Launtop MQ6638-FUZHOU
- Page 1 Original Instructions 8204216 GASOLINE WATER PUMP FIGURE 8204216 Model MQ6638-FUZHOU GASOLINE HIGH PRESSURE PUMP FIGURE Fuzhou Launtop M&E Co., Ltd.
- Page 2 Original Instructions 8204216 No. 56, Jinshan Road, Jinshan Industrial Park, Fuzhou, China...
- Page 3 Original Instructions 8204216 INTRODUCTION Thank you for purchasing the products of our company. Our company’s Gasoline Water (High Pressure)Pump applies the high quality self-priming pump. The engine is air-cooled, direct injection, 4-stroke, gasoline engine or air-cooled, single cylinder,4-stroke gasoline engine. It possesses many good features such as: small in dimensions, light weight, simple structure, convenient to use etc.
- Page 4 Original Instructions 8204216...
-
Page 5: Table Of Contents
Original Instructions 8204216 CONTENTS Gasoline Water Pump Overall Figure……………………………(1) Gasoline High Pressure Pump Overall Figure……………………(1) CHAPTER 1 MAIN TECHNICAL SPECIFICATIONS AND PARAMETER 1. Gasoline Water Pump specifications and parameter …………….(3) 2. Gasoline High Pressure Pump specifications and parameter…….(4) 3. Model Name Identification…………………………………….(5) CHAPTER 2 MAIN STRUCTURE AND USE 1. -
Page 6: Chapter 1 Main Technical Specifications And Parameter
Original Instructions 8204216 CHAPTER 1 MAIN TECHNICAL SPECIFICATIONS AND PARAMETER Gasoline Water Pump specifications and parameter TYPE P50C P80C P100C Suction port 50(2inch) 80(3inch) 100(4inch) dia(mm) Rated displacement (m³/h) max.head(m) Rated head (m) Self-priming time(s/4m) max.suction head Model 160P 160P 240P Rated power(kw/rpm) 2.76/3000... - Page 7 Original Instructions 8204216 TYPE F40C(L) F40C(L)-2 F50C(L) Suction port dia(mm) Discharge port dia(mm) 25x2;40x1 50x1 Capacity(m³/hr) 17(at 35 m Head) 12(at50 m Head) 23(at 30m Head) Max.head(m) Rated head (m) Self-priming time(S/4m) Max.suction head(m) Model 200P Rated power(kw) Displacement(cc) 0.296 Fuel tank capacity(1)
-
Page 8: Chapter 2 Main Structure And Use
Original Instructions 8204216 CHAPTER 2 MAIN STRUCTURE AND USE 1. Main Structure. Water Pump and High Pressure Pump consists of Gasoline engine and pump kit. The pump is fixed on a frame with shock absorbers. The self-priming pump consists of pump body, pump cover, flow guidance, impeller and seals, etc. -
Page 9: Caution
Original Instructions 8204216 (2)Start the engine Please refer to manual engine. 4. Caution (1) The fuel of the pump is Gasoline fuel , not allow mixing of them. Keep fire and other explosives and inflammables away from the pump. Operate the pump on a level surface to prevent fuel spilling. (2) Keep the fuel clean. -
Page 10: Installation Of Connective Soft Pipe
Original Instructions 8204216 between steel part “#7” and pump cover. When fixed it, do not hit by force to prevent wear slice fracture. Please see fig2. Fig 2 stucture diagram of machinery seal 1. seal ring 2.ceramics moving ring 3. graphite static ring 4.corrugated pipe 5.washer 6.spring 7.steel part (7) According to High Presure Pump, the clearance between impeller and regulator is 1mm, when remove or install, can adjust the clearance through adding or reduce the gasket in long shaft screw. -
Page 11: Chapter 3 Analysis Of Malfunction And Remedy
Original Instructions 8204216 CHAPTER 3 ANALYSIS OF MALFUNCTION AND REMEDY Malfunction Cause Remedy Fill water is not enough Refill water into the pump Check inlet pipe and connector of pipe Inlet pipe leakage change Pipe or tighten the screw Speed of pump is too low Check speed and find cause for remedy The filter net is obstructed Check the position of installation... - Page 12 Original Instructions 8204216 Malfunction Cause Remedy Listen to the sound carefully, There is a rub between impeller whether the impeller is clashed and flow guidance with the case and then to adjust The impeller is obstructed by Check and clean up weeds or eyewinker.
- Page 13 Original Instructions 8204216 Stop the machine for checking and Impeller damage change the impeller with a new...
- Page 14 Original Instructions 8204216...
- Page 15 Original Instructions 8204216...
- Page 16 Original Instructions 8204216...
- Page 17 Original Instructions 8204216...
- Page 18 Original Instructions 8204216...
- Page 19 Original Instructions 8204216...
- Page 20 Original Instructions 8204216...
- Page 21 8204216 EC Declaration of Conformity We herewith declare, Fuzhou Launtop M&E Co., Ltd. No. 56, Jinshan Road, Jinshan Industrial Park, Fuzhou, China We declare that the following Appliance complies with the appropriate basic safety and health requirements of the EC Directives (see item 3) based on its design and type, as brought into circulation by us.
- Page 22 Original Instructions 8204216 Note: The person importing the products becomes responsible for ensuring that they comply with the directives which apply to them. At very least, it is recommended that the importer obtain a copy of the original Declaration of conformity from manufacture.
Need help?
Do you have a question about the MQ6638-FUZHOU and is the answer not in the manual?
Questions and answers