Summary of Contents for T&R Site Cut 10
- Page 1 PLASMA CUTTING OPERATING MANUAL Site Cut 10 COMPRESSOR PLASMA CUTTING EQUIPMENT...
-
Page 2: Table Of Contents
2. Safety precautions pag. 2 3. General description pag. 3 pag. 3 3.1. Description of devices on the machine Site Cut 10 power source pag. 4 3.2. Safety devices pag. 4 3.3. Explanation of technical specifications pag. 4 3.4. -
Page 3: Conformity Declaration
Isolate yourselves from both the earth and the workpiece. 1. Conformity declaration Make sure your working position is safe. The machines descripted in this manual, Site Cut 10 must be used solely FUME AND GASES – May be hazardous to your health. for professional purposes in an industrial environment and they are manufactured in compliance with the instructions contained in the harmonized standard EN50199 Keep your head away from fumes. -
Page 4: General Description
6. Positive output terminal 7. Negative output terminal EXPLOSIONS Picture 3 : Site Cut 10 front and Do not weld in the vicinity of containers under pressure, or in the pre- rear view sence of explosive dust, gases or fumes. All cylinders and pressure Figure 3 regulators used in welding operation should be handled with care. -
Page 5: Explanation Of Technical Specifications
PLASMA CUTTING OPERATING MANUAL 3.3 Explanation of technical specification Table 1: Safety device signal. EN 60974.1 The machine has been built according to this European stan- SIGNAL dards FUNCTION EN 50199 ON/OFF ON/OFF EN 50192 Reset function, blink for 5 sec. N.... Serial number. Always indicate this for any request When pilot arc is end Fast blinking for 10 sec. -
Page 6: Technical Specifications Table
3.4 Technical specifications table (table 2) 4.2 Cutting start-up Read the standards CEI 26/9 – CENELEC HD 407 and CEI 26.11 – CENELEC HD Technical data Site Cut 10 433 carefully before using the equipment, and make sure the cable insulation is Main supply (-15%/+15%) 1ph x 230V fully intact. - Page 7 PLASMA CUTTING OPERATING MANUAL On Picture 3 we can see a plot concerning cutting speed vs cutting thickness with Hold the torch upright while cutting. cutting current When you have finished cutting and released the trigger, air will continue to leave the torch for approximately 20-25 seconds to allow the torch to cool down.
-
Page 8: Insufficient Penetration
Oil or dirt in the arc intake. Current/Model From 13 to 18 Amp From 18 to 25 Amp • Unnecessarily long pilot arc. Site Cut 10 Tip diameter 0,65 mmnoz- Tip diameter 0,8 mmnozzle • Low air pressure. zle holder with 2 holes... -
Page 9: Generator Maintenance
Always cut off the power supply to the machine before any operation, which must 8.1 Site Cut 10 power source always carried out by qualified personnel. Figura 10: Viste generali Site Cut 10 7.1 Generator maintenance In the case of maintenance inside the machine, make sure that the switch B is in position “O”... - Page 10 PLASMA CUTTING OPERATING MANUAL Plasma torch T3981120 Hand torch 4 m. - Compressor R4919102 Torch head R4929101 O-Ring R4924109 Electrode Hf - back arc stricking R4622101 Air diffuser R4913130 Tip 0,65 ( 10-20 A ) back arc stricking R4913131 Tip 0,8 ( 20-30A ) back arc stricking R4913132 Tip 0,9 ( 40A ) back arc stricking R4612102...
- Page 11 PLASMA CUTTING OPERATING MANUAL PAGE 10...
- Page 12 Ter s.r.l Via Madonna delle Grazie 27 Costabissara 36030 Vicenza Partita Iva 03377580240 Telefono +39 0444 552887 Internet: http//www.terwelding.com e-mail: info@terwelding.com Telefax +39 0444 284875...