Emerson CKS1800 Owner's Manual page 2

• it shows "1-7", the Everyday mode is selected.
• If it shows "1-5", the Weekdays only mode is selected .
• If it shows "6-7", the Weekends only mode is selected.
To change the Alarm Mode setting for Alarm 1, hold the ALARM 1 setting button
and press the ALARM MODE button until the DAY OF WEEK indicators show the
desired mode setting, Weekdays only, Weekends only, or Everyday operation.
Release the ALARM MODE and ALARM 1 setting buttons and the display will
return to the correct time.
Follow the same procedure to select the desired Alarm Mode for Alarm 2 if necessary.
Checking The Wake Up Times And Alarm Mode
Whenever you want to check the wake up time or the alarm mode settings, simply
press either the ALARM 1 or ALARM 2 setting buttons. The display will change
from correct time to wake up time and the DAY OF WEEK indicators will show you
the alarm mode which is currently selected.
Release the ALARM 1 or ALARM 2 setting buttons to return to correct time.
Listening To The Radio
1.) Press the RADIO ON/OFF button to turn the radio 'On'. The frequency of the
tuning frequency will show for a few seconds on the display.
2.) Set the BAND by pressing BAND button to AM or FM as the desired, it toggles
each time you press the BAND button.
3.) Set the VOLUME by pressing VOLUME + or VOLUME - to a level that is neither
too high nor too inaudible.
4.) Select your desired station with the TUNING control.
a) Press TUNE + or TUNE - slightly, the receiving frequency will increment or
decrement by one step.
b) Press and hold TUNE + or TUNE - for one second then release, Auto Station
Seeking will be engaged, the receiving frequency will increment or decrement
automatically until a station with acceptable reception is found.
5.) Adjust the VOLUME control to the desired setting.
6.) When you are finished listening, press the RADIO ON/OFF button to turn the
radio 'Off'.
Storing and Recalling Radio Station Memory
,
When you have a few favorite radio stations to listen to you may like to save them
and pick one out of them in a few seconds without needing to search it each time
Our digital tuning technology allows you to do this easily by following the following
:
steps
8
Storing to the Memory
1.) Make sure the radio is ON and the AM/FM band is selected.
2.) Tune to the desired station by the TUNING control as described.
3.) Press STORE , "P XX" blinks, indicating the memory location to store the
currently listening station.
4.) While "P XX" is blinking, press TUNE + or TUNE – can change the memory
location from 1 through 10. For e.g . , "P 03" means the current listening
station is about to stored into the 3rd location of the memory.
5.) After deciding the memory location, press STORE again, the currently listening
station is stored.
6.) The display will turn to the frequency of the stations afterwards, and after
a few seconds, the correct time shows.
Recalling Station from the Memory
1.) Make sure the radio is ON and the AM/FM band is selected.
2.) Press MEMORY , "P XX" shows on the display, and the station according to the
memory location is tuned.
3.) While "P XX" is showing on the display, press TUNE + or TUNE – can change
the memory location from 1 through 10, and the station stored in the location
is tuned once the location is changed to.
4.) The display will turn to the frequency of the stations afterwards, and after a
few seconds, the correct time shows.
Antenna Information
AM - The AM bar antenna is inside the cabinet. If AM reception is weak, change
the position of cabinet until the internal antenna picks up the strongest signal.
FM - The FM antenna is built in to the Line cord connecting the AC adapter.
If FM reception is weak try Varying the position and direction of the Line cord
until you find the strongest signal.
Wake To BUZZER
NOTE: Alarm 1 and Alarm 2 have different buzzer sounds.
• Alarm l is a Single beep" sound. " • Alarm 2 is a "Double beep" sound.
You will be able to tell which alarm is going off by the sound that it makes.
1 .) Reconfirm the wake up time and alarm mode settings for the alarm you are
using, Alarm 1 , Alarm 2, or both alarms.
2.) Press ALARM 1 or ALARM 2 button slightly, and repeat doing so if necessary,
until ALARM 1 "BUZZER" or ALARM 2 "BUZZER" indicator is lit on the display.
3.) At the selected wake up time the buzzer will sound. It will continue for one
hour and then shut off automatically.
4.) To stop the buzzer sooner, press the RADIO ON/OFF button. The buzzer will
stop but the alarm remains set and will turn the buzzer on again at the same
time on the following day (depending on the Alarm Mode setting).
5.) If you do not want the alarm to turn the radio on the following day, press the
appropriate ALARM button until the ALARM indicator on the display is OFF.
9
Radio And Buzzer Operation
You may also set one alarm for wake to RADIO and the other for wake to BUZZER.
Just press the ALARM 1 and ALARM 2 buttons to the desired status as shown on the
ALARM indicators.
Snooze/Repeat Alarm
After the alarm turns 'On' in the morning you can SNOOZE/SLEEP OFF button on
the top cabinet for a few extra minutes sleep. The corresponding ALARM indicator
will flash. The alarm will stop for approximately 9 minutes and then comes 'On' again.
The Snooze operation may be repeated several times if desired but after one hour
the alarm will not come on again.
Sleep To Music Timer
You can program the sleep timer to play the radio for up to 90 minutes and then shut
'Off' automatically.
1 .) Press the SLEEP button.The display will briefly
show "10" and the radio will begin to play.
After 10 minutes countdown the radio will shut
off automatically. Each time you press the SLEEP button the sleep timer will
start at 10 minutes. This is the sleep timer default setting.
2.) To increase or decrease the amount of time that the radio will play before
shutting off, hold the SLEEP button and press either the SET + or - button to
change the display to the desired sleep time, up to a maximum of "90" minutes
or a minimum of "02" minutes.
NOTE: When you change the sleep timer from the 10 minute default setting to a
different setting, the new setting becomes the default setting. Whenever you
activate the sleep timer it will begin with your new default setting and count down
to zero from that point.
3.) To cancel the sleep timer before it counts down to '00' and shut the radio 'Off'
immediately, press the SNOOZE/SLEEP OFF Bar.
IMPORTANT: Remember that the station and volume settings you choose for
the Sleep To Music operation are the same settings you will hear if you set the
alarm for Wake To Radio the following morning.
DIMMER Control
The DIMMER control was set to High position at our factory.
If you find the clock display is too bright in a darkened room, set the Dimmer by
,
pressing SNOOZE / SLEEP OFF / DIMMER Button.
.
Changing The Lithium Battery
Like all batteries, eventually the built in lithium battery will need to be replaced. A
number of factors, such as, the length of time between the date the radio was
manufactured and the date you plugged it in for the first time determine the amount
of time before replacement. During this initial storage period, the lithium battery is
10
®
supplying power to the SmartSet computer memory. Once you plug the radio in,
your household outlet supplies the power, and the battery is not being used. A fresh
®
lithium battery can supply power to the SmartSet computer for at least 3 years even
if it is never connected to an AC power supply. If your clock radio was connected to
your AC supply within a few months after it was manufactured, and you experience
only the normal, nuisance type, short duration power interruptions, your battery may
last for up to 5 years or even longer.
,
When the battery power drops below a certain level the
will 'Flash'. When you see this indicator, you should change the battery as soon as
it is convenient for you to do so. To change the battery proceed as follows:
1.) Purchase a replacement 3V lithium battery wherever batteries are sold . The
battery type is CR2032 or equivalent.
2.) Remove the battery from its package so it is ready to install.
IMPORTANT: Leave the AC adapter connected to your AC outlet.
®
This will provide power to the SmartSet computer memory while the original
lithium battery is removed.
3.) Turn the radio face up and use a small screw driver to remove the screw securing
the battery holder to the cabinet.
4.) Remove the original battery from the holder and insert the new battery into the
holder the same way, observing the positive (+) direction. Slide the holder with
the new battery back into the slot in the cabinet.
!
BE CAREFUL NOT TO LOSE THIS SMALL SCREW
5.) Replace the screw that secures the battery holder in the cabinet.
CR2032
POSITIVE(+)
6.) Turn the radio right side up and confirm that the LOW BATT indicator is 'Off'.
7.) Save these instructions. You'll have to do this again five to eight years from Now!
WARNING: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
11
Resetting The Clock After A Total Memory Loss
If you do not change the built in lithium battery within a reasonable period of time
after you see the warning indicator, the lithium battery may become exhausted
a n d w i l l n o l o n g e r b e a b l e t o s u p p l y b a c k u p p o w e r t o t h e S m a r t S e t
internal computer. If the unit is disconnected from the AC outlet after the battery
is exhausted or if a power interruption occurs, the SmartSet memory will be lost
and the clock will need to be reset when the power is restored.
Be sure to install a fresh lithium battery before you reset the clock, otherwise the
clock will need to be reset each time the power is interrupted.
If the lithium battery is exhausted and you experience an interruption in the AC
power supply, the clock will reset itself to its initial default setting when the power is
restored.
The initial default setting is "12:00 AM, Sunday , January 1st (1. 1), 2012".
If you notice that the time on your SmartSet clock radio is completely incorrect,
and the DAY OF WEEK indicator is also wrong, press the MONTH/DATE button to
see the date.
If the date display is showing "1. 1 " (January 1st),
you probably experienced a total memory loss.
To reset the clock after a total memory loss, proceed
as follows:
1 .) Follow the instructions on page 10,11 and install a new CR2032 lithium battery
in the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself.
3.) Depress the MONTH/DATE and TIME buttons together. The display will change
from 'Time' to 'Year'.
W h i l e h o l d i n g i n t h e M O N T H / D AT E a n d T I M E b u t t o n s , p r e s s t h e S E T +
button to set the display to the correct year, then release the buttons.
4.) D e p r e s s t h e M O N T H / D AT E b u t t o n . T h e d i s p l a y w i l l c h a n g e f r o m ' Ti m e '
t o 'Month/Date' (MM/DD).
While holding in the MONTH/DATE button, press the SET + button to set the display
to the correct Month and Date. The DAY OF WEEK indicator will change automatically
as you adjust the Month/Date settings. When the correct Month and Date appear
on the display, release the buttons.
5.) Depress the TIME button and the SET + button to set the display to the correct
Time. Be sure to confirm that you have set the time correctly to 'AM' or 'PM'
by observing the AM indicator.
6.) After you set the Time, reconfirm that the Day, and Month/Date displays are
still correct. Make final adjustments if necessary.
®
The SmartSet clock memory is now reset and the new lithium battery will maintain
it for the next 5 to 8 years, depending on the number and duration of the power
outages you experience.
IMPORTANT NOTE
A f t e r r e s e t t i n g t h e c l o c k , d o n ' t f o r g e t t o r e s e t y o u r w a k e u p t i m e s a n d a l a r m
mode settings, and sleep timer settings as well.
CARE AND MAINTENANCE
Care Of Cabinets
If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet becomes
smudged or dirty, clean it with a soft, slightly dampened cloth .
N e v e r a l l o w w a t e r o r a n y l i q u i d t o g e t i n s i d e t h e c a b i n e t . N e v e r u s e a n y
.
LOW BATT indicator
abrasive cleaners or cleaning pads as these will damage the finish of your radio.
Lithium Battery Precautions
• D i s p o s e o f t h e o l d b a t t e r y p r o p e r l y. D o n o t l e a v e i t l y i n g a r o u n d w h e r e a
young child or pet could play with ,or swallow it. If the battery is swallowed.
contact a physician immediately.
• B a t t e r y m a y e x p l o d e i f m i s t r e a t e d . D o n o t a t t e m p t t o r e c h a r g e i t o r
disassemble it. Do not dispose of the old battery in a fire.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
1-800-695-0098
E-MAIL TO: internet@emersonradio.com
Emerson Radio Corp. warrants manufacturing defects in original material, including
® original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
®
proof of purchase, we will provide repair service at no charge for labor and parts,
or replace the product at our discretion. For repair or replacement, pack your
unit in a padded box, enclose your check or money order payable to Emerson
Radio Corp. in the amount of $9.00 to cover shipping and handling costs, and
enclosed a copy of your proof of purchase. Send your unit to:
®
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
The Serial Number can be found on the bottom cabinet. We suggest that you record
the Serial Number of your unit in the space below for future reference.
Model Number: CKS1800
Serial Number: _ ______ _ _ _ ______ _ _ _ ______ _ _ _ _
12
OR
OR
CKS1800- 305- 00
13
LIMITED WARRANTY
Emerson Returns Facility
11500 Philadelphia ST
Mira Loma, CA 91752
ATTN: Returns Department
AU898N
14
Printed in China
15