Advertisement
Quick Links
SPEX S
HIGH PRESSURE WASHERS
– Please read all instructions before proceeding –
Initial Assembly
To facilitate in the shipment of your pressure
washer, some items require minor assembly.
Refer to the Initial Assembly sheet included for
instructions.
Lubrication
Prior to initial operation ensure that the oil level of
the pump is to the halfway mark of the oil gauge
window. Do not overfill. Use only Magikist high
pressure pump oil or equivalent non-foaming, non-
detergent, 40 weight #1 compressor oil. Do not
use automotive, transmission, or hydraulic oils, or
brake fluid.
Motor Voltage
Ensure that your power supply matches that of the
pressure washer. Do not use any other circuit
unless the motor is rewired by a licensed
electrician. If the pressure washer is unwired, a
Startup Procedure
Ensure that the oil level of the pump is to the
halfway mark of the oil gauge window as
described under Setup.
Attach the water supply hose to the water inlet
connection and turn the water on. Leave the water
supply turned on.
WARNING: IF CONNECTION IS MADE TO A
POTABLE WATER SYSTEM, THE SYSTEM
SHALL BE PROTECTED AGAINST BACKFLOW.
ADVERTISSEMENT: SI CET APPAREIL EST
RACCORDÉ À UN RÉSEAU D'EAU POTABLE,
CE DERNIER DOIT ÊTRE PROTÉGÉ CONTRE
LES RETOURS.
ERIES
SETUP
OPERATION
OPERATING MANUAL
licensed electrician should be retained in order to
carry out the proper installation.
Water Inlet Connection
The water inlet connection is a 3/4" female hose
coupling located on the front right side of the
water tank. It is connected to a float assembly
which automatically maintains the correct water
level in the water reservoir.
Attach your water supply hose to the water inlet
connection and turn the water on. Leave the water
supply turned on. Ensure that your water supply is
of adequate capacity such that the water reservoir
does not run empty.
Do not disconnect the suction line between the
pump and the water reservoir and feed the pump
directly without the use of a pressure reducing
valve to reduce inlet pressure to 20 PSI.
Ensure that the power switch for the electric motor
is in the OFF position. Connect the electric motor
to the power supply.
Grasp the trigger gun firmly and turn the power
switch for the electric motor to the ON position.
Pull back on the trigger of the spray gun to spray.
If after a short while only a trickle of water is
coming out the the spray nozzle or if the water is
spurting out, you may need to purge air from the
pump. See the subsection Purging Air for
instructions on purging air from the pump.
WARNING: DO NOT SPRAY ELECTRICAL
APPARATUS AND WIRING.
ADVERTISSEMENT: IL EST DANGEREUX DE
TROP ARROSER LE MATÉRIEL ET LES
CÂBLES ÉLECTRIQUES.
Advertisement
Summary of Contents for Magikist SPEX SERIES
- Page 1 Do not overfill. Use only Magikist high pressure pump oil or equivalent non-foaming, non- Attach your water supply hose to the water inlet detergent, 40 weight #1 compressor oil.
- Page 2 Note on first time operation: If this is the first Soap Container time you are using your pressure washer it is a Liquid soap may be added directly to the soap good practice to flush the system to remove any container through the filler spout.
-
Page 3: Maintenance
Do not suction hose in the water reservoir has no breaks overfill. Use only Magikist high pressure pump oil in the screen and that it is free of particles which or equivalent non-foaming, non-detergent, 40 might restrict flow. -
Page 4: Troubleshooting
TROUBLESHOOTING Symptom Probable Cause Correction •Motor does not start. •Motor not connected to power •Connect the motor to the power supply. supply. •A fuse has blown or breaker has •Change the fuse or reset the tripped. breaker. •Thermal overload tripped. •Allow the motor to cool. -
Page 5: Warranty
Based on the logical assumption that manufacturing and material deficiencies will manifest themselves within one years time, all Magikist pumps are warranted for one year from date of purchase, by the original purchaser, against defective material and workmanship provided the equipment is installed and operated in accordance with factory recommendations and instructions.