Table of Contents
Advertisement
Quick Links
c
Dimensions
Flue types:
C 12 or 42: horizontal
C 32 xx:
vertical concentric
C 32 xy:
Twin flue
Technical data
Heat input C/H
System 80 :
System 100 :
Heat output C/H
System 80 :
System 100 :
Max. operating pressure C/H circuit :
Expansion vessel net capacity
Expansion vessel initial pressure
Nominal gas flow rate at 15°C and 1013 mbar
-Natural gas ( G 20) at 20 mbar
-Butane gas ( G 30 ) at 28 mbar
-Propane gas ( G 31 ) at 37 mbar
Injectors and gas valves seat diameter
-Blue solenoid restrictor diameter
-Gas valve restrictor diameter
-Manifold injectors (16)
MAINTENANCE AND
SERVICE GUIDE
Central Heating
Fanned Flue Boiler
Boiler outer case dimensions :
- Height : 850
- Boiler width : 440 (minimum space required 450)
- Depth : 380
11.73 to 28,70 kW
15.43 to 34.50 kW
9.50 to 24 kW
12.50 to 28 kW
2.5 bar
:
5.4 l
:
0.7 bar
BRITONY System II 80
Maximum
power kW
2.74 m
3
/h
2.04 kg/h
2.00 kg/h
BRITONY System II 80
Natural gas
2.60 mm
6.70 mm
1.23 mm
System II 80 and 100
Electrical consumption
Voltage
Electrical protection index
Fuses
Gas category
Minimum
power kW
power kW
1.22 m
3
/h
0.91 kg/h
0.89 kg/h
Butane or Propane
Natural gas
1.75 mm
4.90 mm
no restrictor required
0.70 mm
Sizes in mm
I
Safety valve outlet
J Heating flow
L Gas supply
N Heating return
:
150 w
:
230 v
:
IP24
:
2 A and 1.25 A
:
II 2E+ 3+
BRITONY System II 100
Maximum
Minimum
power kW
3.34 m
3
/h
1.57 m
2.45 kg/h
1.17 kg/h
2.42 kg/h
1.15 kg/h
BRITONY System II 100
Butane or Propane
2.90 mm
2.00 mm
6.70 mm
1.26 mm
0.76 mm
3
/h
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for C&M BRITONY System II 80
Summary of Contents for C&M BRITONY System II 80
-
Page 1: Technical Data
Gas category II 2E+ 3+ Expansion vessel net capacity 5.4 l Expansion vessel initial pressure 0.7 bar Nominal gas flow rate at 15°C and 1013 mbar BRITONY System II 80 BRITONY System II 100 Maximum Minimum Maximum Minimum power kW... -
Page 2: Pump And Expanssion Vessel Characteristics
Pump and expanssion vessel characteristics PUMP HEAD AVAILABLE Pression disponible Minimum flow rate (with all heating thermostatic valves closed) Débit mini (robinets thermostatiques fermés) m CE Flow Débit 1000 1100 1 = by-pass closed 2 = by-pass open Note : The system initial pressure should be over the following value : System static height (in metre) + 0.7 = Initial pressure (in bar) Head available / flow Components location... -
Page 3: Components Location
FUNCTIONING COMPONENTS LOCATION Switching on 1) Check that the gas service tap is opened at the gasmeter and main power is on. 2) Check that pressure in central heating system is above 0.7 bar and below 2.5 bar with the pressure gauge 3) Open the gas tap 3 by turning from right to left. -
Page 4: Central Heating
Central Heating It is possible to override the 3 minute delay by pressing the To be able to supply heating, the main switch 15 must be RESET button 23 turned fully clockwise to position. This will be confirmed by the green indicator light Lock out procedure When there is a demand for heating (either from the room Flame disappearance :... -
Page 5: Routine Servicing
ELECTRICAL WIRING continuation ADJUSTMENTS ON CONTROL PCB N° Designation Wiring colours The following adjustments are available on the regulation PCB. To -Overheat sensor Brown gain access to them, pivot down electrical box, remove the rear -Electrical box cover and the rear panel of electrical box, unplug connectors from 14a. -
Page 6: Removal And Replacement Of Parts
REMOVAL AND REPLACEMENT OF PARTS Before removing appliance case, isolate 5. Ignition Electrodes 10. Pressure Switch the gas and electrical supplies. Isolate boil- Carry out steps 1 and 2 as above. Hinge Remove outer case and sealed chamber er from the system and drain before down electrical box by pressing retaining front panel as in steps 1 and 2. - Page 7 14. Flow switch 20. Thermistor Drain boiler as in step 12. Disconnect the Drain the boiler as step 12. Disconnect the plug, remove the retaining clip pull the electrical plug, turn the top cover anti- thermistor out. Reassemble in reverse order. clockwise, remove the O-ring and the 37 = Heating thermistor brass piston.
-
Page 10: Short List
SHORT LIST Manf. date Key N° Description G.C N° Manf. Pt. N° Type FF FF from 277783 1010572 OVERHEAT THERMOSTAT 100°C 277788 1002801 IGNITION ELECTRODE ASSY 277789 1002802 IONIZATION ELECTRODE 277790 1010017 HEAT EXCHANGER E00606 1011136 HEAT EXCHANGER 1304720 FAN ASSY 1304721 FAN ASSY 1306697... - Page 11 Notes...
- Page 12 This appliance is suitable for Natural gas or LPG. A gas conversion must be made by a competent person. Chaffoteaux & Maury are continuously improving their products and therefore reserve the right to change specifications without prior notice and accepts no liability for any errors or omission in the information contained in this document. Manufacturer: Chaffoteaux &...
Need help?
Do you have a question about the BRITONY System II 80 and is the answer not in the manual?
Questions and answers