Introduction Thank you very much for purchasing the xelaris XT-6 2.4 GHz 6-channel transmitter. Please read this manual completely and carefully before using the transmitter. This manual includes a great variety of information to operate the transmitter safely. The XT- 6 is a proportional 6-channel radio control system, which was developed in cooperation with Heli-Professional.
Display: Color: Black/Blue Important Information Never use the xelaris XT-6 transmitter in rainy conditions. Water destroys the sensitive electronics of the transmitter and leads to a loss of control of the model. Make sure that the bind switch is not in the binding mode during flights.
Page 5
ŸDust ŸThe transmitter must not be cleaned with chemicals or abrasive detergents If you want to store the transmitter for a longer period of time, remove the batteries and store them separately to avoid any damage on the device. www.xelaris.ch...
As soon as the battery voltage drops 2) Decrease Selected Data below 8.5 V, the red LED will start to V) LEFT Key, Next Selection Left blink. W) Handle WARNING: Replace the batteries X) Bind Button immediately! Y) Simulator Socket Z) Battery Compartment A1)Charging Socket www.xelaris.ch...
If you unintentionally press Y/UP in the menu Mode Select of an existing model, all data will be overwritten with a completely new model. To recover the data, reload the model in the menu Load. Switching the transmitter on and off does not recover the data! www.xelaris.ch...
Page 8
2. Channel Reversal The direction of every channel can be electronically reversed in the xelaris XT-6 transmitter. Proceed as follows: 1. Press the MENU key until you get to the main menu Rev. 2. Choose a channel with the LEFT and RIGHT keys and reverse it with the Y/UP key.
Page 9
2. Adjust the value with the Y/UP and N/DOWN keys between -100% and +100%. 4.Throttle and Pitch Curves The xelaris XT-6 transmitter offers the possibility to program two different 5-point throttle and pitch curves. Press the MENU key until you get to the main menu CUV.
Page 10
5. Mixer (for A, V and D) The xelaris XT-6 transmitter is equipped with four programmable mixer. The necessary mixer are already programmed when you have chosen either a delta model or a V-tail model. To add further mixer or to adjust existing mixer, proceed as follows: Press the MENU key until you get to the main menu Mix.
Y/UP and N/DOWN keys between +100% and -100%. Save changes according to step 1.2! 6.5 Changing the Mode The xelaris XT-6 transmitter allows you to change the mode instantly. WARNING: Never change the mode when the model is switched on! 1.
Channel 1 / Aileron Channel 1 / Roll Power Supply The xelaris XR-6 2.4GHz receiver needs a constant power supply between 4.8V and 6V to work properly. The electric circuit of the receiver must be sufficiently dimensioned to operate all servos.
If you move the stick backwards, the model will descend. If you move the stick to the left, the model will turn counterclockwise. If you move the stick to the right, the model will turn clockwise. www.xelaris.ch...
If you move the stick forwards, the motor speed will increase. Rudder If you move the stick to the left, the model will move to the left. If you move the stick to the right, the model will move to the right. www.xelaris.ch...
In case you want to bind a gasoline powered model, connect the external power supply with any socket of the receiver. Connect the power supply to its designated socket after the binding process is complete. www.xelaris.ch...
1. Switch the transmitter off (as long as the transmitter is switched on, it will not be charged). 2. Connect the charging cable. To extend the durability of the transmitter battery, do not charge it for more than five hours! www.xelaris.ch...
Flowchart (1-9,A,b,C) (1-9,A,b,C) (CH1-6) Keys (CH1,2,4) MENU LEFT / RIGHT (CH1,2,4) Y/UP N/DOWN (CH1-6) (A E r) (A E P) (A,V,D) (PT1-5) (H, C) (PT1-5) (PT1-5) (PT1-5) (A,V,D) (Mix 2,3,4 Set as Mix 1 ) (CH1-6) (CH1,2,4,6) www.xelaris.ch...