Related Manuals for Acumen Tempest Cat1
Summary of Contents for Acumen Tempest Cat1
- Page 1 User Guide Tempest Cat 1 VERY IMPORT NT INFORM TION It is VERY important you set up your PIN Override - Section 16 on page 8. Make sure you know where your System Fuse and Spare Fuse are located. See ertificate of Installation.
-
Page 2: Table Of Contents
Index System overview The remote transmitter Customising the system Section 1. Full Mode Section 2. Convenience Mode Section 3. Service Mode Section 4. Diagnostic Mode Section 5. Different siren tones Section 6. Customising udible warning of rm/Disarm Section 7. Hazard (4-way flasher) Mode Section 8. -
Page 3: System Overview
The Tempest CAT1 also; 1. Has a ‘fully armed’ mode (see section 1) 2. Has a ‘Convenience’ mode (see section 2) The Acumen Tempest CAT1 consists of the following main components; 3. Has a service/valet mode (see section 3) 4. Has a diagnostic mode (see section 4) •... -
Page 4: The Remote Transmitter
The Remote Transmitters This button will; This button will; Ignition key • rm & disarm the system, • Deactivate/activate tilt The system is supplied with 2 transmitters, 1 flip fob and 1 lightweight and vibration, fob. The key blank for the flip fob is supplied by cumen on receipt of •... -
Page 5: Customising The System
Customising the system Section 1. Full Mode button once to manually arm the system before the 50 seconds elapses and then the ‘P’ button to enter To passively arm the system automatically with all functions enabled, Convenience Mode. permanently connect the Yellow wire from the alarm to a suitable earth (ground) point. -
Page 6: Section 4. Diagnostic Mode
Customising the system Section 4. Diagnostic Mode Section 5. Different siren tones Diagnostic Mode will let the system tell you why it has been reacting. If Having an individual siren tone helps you, the user, to be you experience alarms, it helps to know why. The Tempest C T1 system more aware if it’s your alarm that is making that noise! TheTempest will tell you. -
Page 7: Section 7. Hazard (4-Way Flasher) Mode
Customising the system Section 7. Hazard (4-way flasher) Mode Section 9. Indicator warning With the motorcycle ignition off, system armed or disarmed, Hold the The cumen Tempest C T1 system can be set as a turn ‘key’ and ‘P’ button down simultaneously for approx 3 secs. signal reminder. -
Page 8: Section 11. Remote Transmitter Battery Low Warning
Customising the system Section 11. Remote Transmitter battery low warning. Section 13. Key Conversion Whenever the remote transmitter is used, the alarm monitors the state On registering the alarm as of the transmitter’s batteries. When the batteries start to become first or subsequent owner you discharged, the Tempest C T1 system will tell you with a burst of 6 will receive a key blank. -
Page 9: Section 16. Pin Override
Customising the system Section 16. PIN Override TO ENTER THE INITI L PIN You can now enter the pin of your choice; say 4 digits - 1234 If you cannot disarm the system from the Each step in this process will be confirmed by remote transmitter - see troubleshooting, - you beeps or tones: Ignition on, count 1 beep, ignition off... - Page 10 Customising the system ENTERING NEW PIN WHEN PIN IS Now enter the new pin (say, 6789) by DIS RMING THE SYSTEM USING LRE DY KNOWN. Ignition on, count 6 beeps, ignition off THE PIN OVERRIDE From time- time you may wish to change the Ignition on, count 7 beeps, ignition off If the system is armed and you cannot disarm it PIN that is in the system.
-
Page 11: Troubleshooting
Troubleshooting The cumen Tempest C T1 is manufactured using automotive 4. Check the Tempest C T1 system can obtain service mode (section specification parts, including waterproof connectors, and is fully 3) If the Tempest C T1 cannot obtain Service mode, it means the encapsulated to provide protection against water and vibration. -
Page 12: Maintenance
Motorcycle Battery 5. Tracker upgrade available - see www.acumen-electronics.co.uk The Tempest C T1 system incorporates a sleep mode (see section 15) dditional magnet sensors (such as seat, or link to your garage to protect the motorcycle battery from deep discharge. Should you wish door).
Need help?
Do you have a question about the Tempest Cat1 and is the answer not in the manual?
Questions and answers
I've disconnected my motorbike battery and when I went to reconnect the Acumen cat 1 alarm constantly goes off and I cant reset it with the fob
To reset the Acumen Tempest Cat1 alarm after reconnecting the motorcycle battery, follow these steps:
1. Disarm the system using the transmitter – Press the ‘P’ button on the transmitter.
2. If the transmitter does not work, use the PIN override:
- Switch on the motorcycle ignition and leave it on (1 beep will confirm this).
- Enter your PIN by turning the ignition on and off according to your set PIN code.
- If entered correctly, the alarm will disarm.
If the alarm continues to go off, check:
- The system fuse to ensure the alarm has power.
- The motorcycle battery condition.
- If the unit is in sleep mode, connect a charger to wake it up.
If issues persist, replace the transmitter batteries or reprogram the PIN following the manual instructions.
This answer is automatically generated