Summary of Contents for Zksoftware iFace 100 Series
Page 1
iFace 100 Series Product User Manual Version: 1.1 Date: August 2011 About This Manual This document introduces the user interface and menu operations of the iFace100 series products. For the installation, see iFace100 Series Products Installation Manual...
Page 2
About this manual All features are subject to the actual product. We can neither promise that the information consistent with the actual product because of the constantly updated of product, nor assume any dispute resulting from the actual technical parameters does not match this information, any change without prior notice. The ★ marked feature of the manual that not all equipment available. Please subject to the actual product. Captions in this document may does not match the picture of the product, Please subject to the actual product.
iFace100 Series Product User Manual Content 1 Instruction for Use..................1 1.1 The Distance,Facial Expression and Stand Pose....... 1 1.2 Enrollment Pose ................... 2 1.3 Finger Placement.................. 3 1.4 Appearance of the iFace100 product serials ........4 1.5 Main Interface ..................6 1.6 Verification Modes ................7 1.6.1 Fingerprint Verification★ ............7 1.6.2 Face Verification ..............9 1.6.3 Password Verification............11 1.6.4 ID Card Verification ★ ............12 2 Main Menu ....................15 3 Adding a User .....................17 3.1 Assign user ID..................18 3.2 Input user name .................. 19 3.3 Enrolling a Fingerprint★..............20 3.4 Enrolling a Password .................
Page 4
content 6.1 General Parameters ................33 6.2 Display Parameters ................34 6.3 Fingerprint Parameters★ ..............35 6.4 Face Parameters ................. 37 6.5 Log Settings ..................39 6.6 Keyboard Definitions ................. 40 6.7 Update ....................42 7. Data Management ..................43 7.1 Query a Record .................. 44 8 Date/Time Setting ..................46 8.1 Set Date/Time ..................46 8.2 Bell Setting ★................... 47 9. Auto Test.....................50 10 USB Disk Management................52 11 System Information..................54 Appendix......................56 Appendix 1 T9 Input Method..............56 Appendix 2 Photo ID Function★...
iFace100 Series Product User Manual 1 Instruction for Use 1.1 The Distance,Facial Expression and Stand Pose 1)The recommended distance: The recommended distance between person and device is 0.5m (applied to height range 1.5~1.85m). According to the obtained face image from device to adjust, when the face image is comparatively bright, please move backwards appropriately; when the face image is comparatively dark, please move forwards appropriately. ...
1 Instruction for Use 1.2 Enrollment Pose During the enrollment, display the face in the centre of screen as possible. According to the device’s voice prompts, do some smallscope head actions such as turn left, turn right, rise, bow and so on to ensure that the different parts of face are inputted into system to improve the verification accuration. The enrollment poses are as follows: Focus on Focus on Turn left Turn right Look ahead the camera slightly (rise) the screen slightly (bow) 2 ...
iFace100 Series Product User Manual 1.3 Finger Placement Recommended fingers: The index finger, middle finger or the ring finger; the thumb and little finger are not recommended (because they are usually clumsy on the fingerprint collection screen). 1) Proper finger placement: The finger is flat to the surface and centered in fingered guide. 2) Improper finger placement: Not flat to the surface Offcenter Offcenter Slanting Please enroll and verify your fingerprint by using the proper finger placement mode. We shall not be held accountable for any consequences arising out of the degradation in verification performance due to improper user operations. We shall reserve the right of final interpretation and revision of this document. 3 ...
1 Instruction for Use 1.4 Appearance of the iFace100 product serials Indicator Keypad Fingerprint sensor ID card swipe area TFT screen Camera Indicator Keypad TFT screen Camera The feature may be different from your device. Please subject to the actual product. 4 ...
Page 9
iFace100 Series Product User Manual Keypad: key function Numeric 1. 0~9,used to input employee number, password and so on. key 2. used to enter characters in T9 Input. ESC 1. Cancel the operation and return to the superior menu. 2. close T9 input. MENU menu, OK Space back. Press it when User ID, password, and system value are input incorrectly to delete the wrong value and input the value again.。 OK OK * 1. page up & page down key in list page 2. shortcut. # 1. page up & page down key in list page 2. shortcut. 1. upward. F1/▲ 2. shortcut. 1. downward. F2/▼ 2. shortcut. ...
1 Instruction for Use 1.5 Main Interface ① Date ② Time ③ Attendance Status ④ Facial/Fingerprint Image ① Date: Current date is displayed. ② Time: Current time is displayed. Both the 12hour and 24hour time systems are supported. ③ Attendance Status: Current attendance status is displayed. ④ Facial/Fingerprint Image: If a facial image is displayed, the terminal is currently in the facial recognition mode; if a fingerprint image is displayed, the terminal is currently in the fingerprint recognition mode. You can change current recognition mode ...
1.6 Verification Modes 1.6.1 Fingerprint Verification★ 1. 1: N fingerprint verification In this fingerprint verification mode, the device compares current fingerprint collected by the fingerprint sensor with all fingerprint data on the device. Place the enrolled finger Wait a second before The terminal verifies properly on the removing the finger from user, displays the ID and fingerprint sensor. the fingerprint sensor. . prompts “Verified” If verification failed, the terminal prompts “Please try again”.
Page 12
1 Instruction for Use 2. 1:1 fingerprint verification In the 1:1 fingerprint verification mode, the device compares current fingerprint collected through the fingerprint sensor with that in relation to the user ID entered through the keyboard. Adopt this mode only when it is difficult to recognize the fingerprint. Enter the user ID by the Press F3 to start 1:1 Place the enrolled finger fingerprint verification. keypad. properly on the fingerprint sensor. The terminal verifies If verification failed, the user, displays the ID and terminal prompts “Please . ...
iFace100 Series Product User Manual 1.6.2 Face Verification 1. 1:N face verification In this face verification mode, the device compares current face collected through the camera with all face data on the device. Compare the facial in a Wait a second. The terminal verifies proper way. For details, user, displays the ID and see 1.1 Standing prompts “Verified” Position and Posture, and Facial Expression. 9 ...
Page 14
1 Instruction for Use 2. 1:1 face verification In the 1:1 face verification mode, the device compares current face collected through the camera with that in relation to the user ID entered through the keyboard. Adopt this mode only when it is difficult to recognize the face. Enter the user ID by the Press F2 to start 1:1 Compare the facial in a face verification. keypad. proper way. For details, see 1.1 Standing Position and Posture, and Facial Expression. The terminal verifies ...
iFace100 Series Product User Manual 1.6.3 Password Verification In the password verification mode, the device compares the password entered with that in relation to the user ID. Enter the user ID by the Press F4 to start Enter the password password verification. keypad. using keypad. The terminal verifies If verification failed, the user, displays the ID and terminal prompts “Please . prompts “Verified” try again”. 11 ...
1 Instruction for Use ★ 1.6.4 ID Card Verification ? Note: Only the products with the builtin ID card module support the ID card verification. Only the products with a builtin ID card module support the ID card verification. The products with a builtin ID card module support the following three verification modes: ID Card Only: Users only need to swipe their ID cards for verification. ID + Facial or fingerprint Verification: After passing the ID card verification, you also need to perform facial verification or fingerprint verification. For the settings of these two verification modes, see 5.5 Attendance Parameters. 1) ID Card Only Swipe the card at the The ...
Page 17
iFace100 Series Product User Manual 2)ID + Facial Verification Swipe the card at the Compare the facial in a The terminal verifies induction area. proper way. For details, user, displays the ID and see 1.1 Standing prompts “Verified” Position and Posture, and Facial Expression. 13 ...
Page 18
1 Instruction for Use 3)ID + fingerprint Verification Swipe the card at the Place the enrolled finger The terminal verifies induction area. properly on the user, displays the ID and fingerprint sensor. . prompts “Verified” If verification failed, the terminal prompts “Please try again”. 14 ...
iFace100 Series Product User Manual 2 Main Menu There are two types of rights respectively granted to two types of users: the ordinary users and administrators. Ordinary users are only granted the rights of facial, fingerprint, password or card verification, while administrators are granted the access to the main menu for various operations apart from having all the privileges granted to ordinary users. ...
Page 20
2 Main Menu Add User: Enroll employee’s fingerprint, password or facial in the device. User Mgt.: Through this submenu, you can browse the user information stored on the terminal, including the user ID, name, fingerprint, facial, card, password, rights and group No.; add, modify or delete the user information. Comm.: Through this submenu, you can set related parameters for communication between the terminal and PC, including the IP address, gateway, subnet mask, baud rate, equipment No. and communication password. System: ...
iFace100 Series Product User Manual 3 Adding a User Enroll employee’s fingerprint, password or facial in the device for attendance. Press MENU once. Press OK once User ID: Enter a user ID. 1 to 9digit user IDs are supported by default. Name: Enter a user name. 12character user names are supported by default. Fingerprint: Enroll a user’s fingerprint and the terminal displays the number of enrolled fingerprints. A user can enroll 10 fingerprints at maximum. Password: Enroll a user’s password. 1 to 8digit passwords are supported by default. Card: Enroll a user’s card. Face: Enroll a user’s face. Role: Set the rights of a user. A user is set to ordinary user by default and can also be set to administrator. Ordinary users are only granted the rights of facial, fingerprint or password verification, while administrators are granted the access to the main menu for various operations apart from having all the privileges ...
3 Adding a User 3.1 Assign user ID The terminal automatically allocates an ID starting from 1 for every user in sequence. If you use the ID allocated by the terminal, you may skip this section. Press MENU once. Press OK once. Press OK once. Tip: The user ID can be modified during initial enrollment, but once enrolled, it cannot be modified. Assign user ID for the user. Assign user ID successful ...
iFace100 Series Product User Manual 3.2 Input user name Enter a user name through T9 input method. Input the user name.Pres Press F2/q once. Press once to start The steps please see T9 input. Appendix 1 T9 Input Method Press to end input. Tip: The terminal supports the 1 to 12character names by default. Input user name successful. 19 ...
3 Adding a User 3.3 Enrolling a Fingerprint★ Press F2/q 2 times. Press once to enroll FP. Place the same finger on the fingerprint sensor for three consecutive times correctly. Enroll fingerprint successful. Press AB once to save and return to the main menu Tip: Only some models have the fingerprint options. 20 ...
iFace100 Series Product User Manual 3.4 Enrolling a Password Press F2/q 3 times . Press once to enroll . Enter password maximum 8 digits. password. Press Ok once. consecutive times correctly. Reenter the password to Press AB once to save conform. Press once to and return to the main menu save. 21 ...
3 Adding a User 3.5 Enrolling an ID Card ★ Swipe your ID card properly in Press F2/q 4 times. Press once to enroll card. the swiping area. Enroll card successful. Press AB once to save and return to the main menu Tip: Only some models have the ID card options 22 ...
iFace100 Series Product User Manual 3.6 Enrolling a Face Turn your head to the left and Press F2/q 4 times. Press once to enroll face. right slightly, raise and lower your head according to the voice prompts, so as to enroll different parts of your face into the system to assure accurate verification. See 1.1 The distance, Facial Expression and Stand Pose.
3 Adding a User 3.7 Modify User Rights There are two types of rights respectively granted to two types of users: the ordinary users and administrators. Ordinary users are only granted the rights of facial, fingerprint, or password verification, while administrators are granted the access to the main menu for various operations apart from having all the privileges granted to ordinary users. Press F2/q 5 times. Press OK once to select Press AB once to save Administrator ...
iFace100 Series Product User Manual 3.8 Enroll Photos★ If you have enrolled your photo in the system, the system will display your enrolled photo in addition to your ID and name after you pass the verification. stand naturally in front of the Press F2/q 6 times. Press once to enroll screen. For details, see 1.1 photo. Standing Position and Posture, and Facial Expression. Press AB once to save Reenter the password to and return to the main conform. Press once to ...
4. User Management 4. User Management Browse the user information, including the user ID, name, fingerprint, face, ID card, password, rights and the group that the user belongs to. Add, edit or delete the basic information of users. . Press MENU once Press MENU once Press F4/u once to select User Mgt. Press OK once 26 ...
iFace100 Series Product User Manual 4.1. Adding a User In order to add user conveniently for operator, add is configured here. The function is the same as that of 3 adding a user. 4.2 Delete a User On the [User Management] interface, you can delete user information. . . Press MENU once Press once Press F1/p or F2/q to . chose user ID to delete Press MENU once Press F2/q once. Press OK once Press ESC once to return to the main menu 27 ...
4. User Management 4.3 Edit a User . Press F1/p or F2/q to Press F2/q 2 times Edit the user information. . chose user ID to edit Press AB once to save Press OK once Press MENU once and return to the main menu The User ID cannot be modified, and the other operations are similar to those performed to add a user. You can reenroll your fingerprint and facial image, change ...
iFace100 Series Product User Manual 4.4 Query a User To facilitate administrators to locate a user quickly from a large number of enrolled users, the terminal enables user query by his/her “User ID” (Location Search) . Press F1/p or F2/q to Press F2/q 3 times Input the user ID. . chose user ID to edit Press OK once Press MENU once For example: input The cursor locate the desired user. 10007. Press AB once to save and return to the main menu 29 ...
5 Communicationrelated Settings 5 Communicationrelated Settings You can set related parameters for the communication between the terminal and PC, including the IP address, gateway, subnet mask, baud rate, equipment No. and communication password. Press MENU once. Press F4/u 2 times to select Comm. Press OK once When the terminal communicates with the PC over Ethernet, you need to check the following settings: IP Address: The IP address is 192.168.1.201 by default and can be changed as required; the IP address of the terminal and that of the PC cannot be duplicated. Subnet Mask: The subnet mask is 255.255.255.0 by default and can be changed as required. Gateway: The gateway is 0.0.0.0 by default. If the terminal and the PC are not located in the same network segment, you need to set the gateway. When the terminal communicates with the PC over serial ports (RS485), you need to check the following settings: ...
Page 35
iFace100 Series Product User Manual RS485: This parameter is used to enable or disable the RS485 communication. If the RS485 communication cables are used, set this parameter to “ON”. Baud Rate: This parameter is used to set the baud rate for the communication between the terminal and the PC. It includes five options: 9600, 19200, 38400, 57600, and 115200. The high baud rate is recommended for the RS232 communication ...
6. System Configuration 6. System Configuration Through the [System] menu, you can set systemrelated parameters, including the basic parameters, interface parameters, fingerprint, facial and attendance parameters, to enable the terminal to meet user requirements to the greatest extent in terms of functions and display. Press MENU once Press F2/q once to select System. Press OK once 32 ...
iFace100 Series Product User Manual 6.1 General Parameters Press OK once Keyboard Clicks: This parameter is used to set whether to generate beep sound in response to every keyboard touch. Select “ON” to enable the beep sound, and select “OFF” to mute. Voice Prompts: This parameter is used to set whether to play voice prompts during the operation of the terminal. Select “ON” to enable the voice prompt, and select “OFF” to mute. Volume (%): This parameter is used to adjust the volume of voice prompts. Lock Power Key: This parameter is used to set whether to lock the power key. Select “ON” to disable the power key. If you select “OFF” and press the power key, the terminal will be shut down in three seconds. 33 ...
6. System Configuration 6.2 Display Parameters Language: This parameter is used to display the current language used by the terminal. For multilingualcapable terminals, you can switch between different languages through this parameter. Toolbar: This parameter is used to display style of the shortcut keys on the initial interface. It can be set to “Auto Hide” and “Permanent Display”. By selecting “Auto Hide”, you can manually display or hide the toolbar. By selecting “Permanent Display”, you can permanently display the toolbar on the initial interface. Default Verify Mode: This parameter is used to set the default verification mode, that is, the "Fingerprint" or “Face” verification mode. Picture Delay (S): This parameter is used to set the picture cycle interval (value ...
iFace100 Series Product User Manual 6.3 Fingerprint Parameters★ Press F2/q 2 times. Press OK once 1: 1 Threshold: This parameter is used to set the threshold of matching between current fingerprint and the fingerprint template enrolled in the terminal in the 1:1 verification mode. If the similarity between current fingerprint and the fingerprint template enrolled in the terminal is larger than this threshold, the matching is successful; otherwise, the matching is not successful. 1: N Threshold: This parameter is used to set the threshold of matching between current fingerprint and the fingerprint template enrolled in the terminal in the 1:N verification mode. If the similarity between current fingerprint and the fingerprint template enrolled in the terminal is larger than this threshold, the matching is successful; otherwise, the matching is not successful. The recommended thresholds are as follows: 35 ...
Page 40
6. System Configuration Threshold False Rejection 1: N 1:1 Rate (FRR) False Acceptance Rate (FAR) High Low 45 25 Medium ...
iFace100 Series Product User Manual 6.4 Face Parameters Press F2/q 3 times. Press OK once 1: 1 Threshold: This parameter is used to set the threshold of matching between current face and the facial template enrolled in the terminal in the 1:1 verification mode. If the similarity between current face and the facial template enrolled in the terminal is larger than this threshold, the matching is successful; otherwise, the matching is not successful. The valid value scope is 55─120. The higher the threshold, the lower the FAR and the higher the FRR, and vice versa. 1: N Threshold: This parameter is used to set the threshold of matching between current face and the facial template enrolled in the terminal in the 1:N verification mode. If the similarity between current face and the facial template enrolled in the terminal is larger than this threshold, the matching is successful; otherwise, the matching is not successful. The valid value scope is 65─120. The higher the threshold, the lower the FAR and the higher the FRR, and vice versa. The recommended thresholds are as follows: 37 ...
Page 42
6. System Configuration Threshold FRR FAR 1: N 1:1 High Low 90 80 Medium ...
iFace100 Series Product User Manual 6.5 Log Settings Press F2/q 4 times. Press OK once Log Alert: When the available space is insufficient to store the specified number of attendance records, the terminal will automatically generate an alarm. (Value scope: 1─99) Dup. Punch Period (m): If a user’s attendance record already exists and the user punches in again within the specified period (unit: minute), his/her second attendance record will not be stored. (Value scope: 1─60 minutes) Card Only: If this parameter is set to “YES”, you pass the verification only after card verification. If this parameter is set to “NO”, you need to verify your face or fingerprint after card verification. Notice: Card Only function is only available on some models. 39 ...
6. System Configuration 6.6 Keyboard Definitions You can define six shortcut keys as attendance status shortcut keys or functional shortcut keys. On the main interface of the terminal, press corresponding keys and the attendance status will be displayed or the function interface will be rapidly displayed. Press F2/q 5 times. Press OK once Press OK once Press once You can set the functions of When ...
Page 45
iFace100 Series Product User Manual Press to set the Set the Auto Switch F2/q Auto Switch. Press AB 2 times to Press once save and return to the main menu Function: You can set the functions of different shortcut keys, such as functional shortcut keys, attendance status shortcut key and work code shortcut key. ...
6. System Configuration 6.7 Update You can upgrade the firmware program of the terminal by using the upgrade file in the USB disk through this parameter. If you need the firmware upgrade file, please contact our technical support personnel. Generally the firmware upgrade is not recommended. 42 ...
iFace100 Series Product User Manual 7. Data Management Through the [Data Mgt.] menu, you can perform management of data stored on the terminal, for example, deleting the attendance record, all data, purging management rights and resetting the terminal to factory defaults. Press MENU once Press F2/q once and F4/u once to select Data Mgt. Press OK once Delete Transactions: Delete all the attendance records. Delete All Data: Delete all the information of enrolled personnel, including their fingerprints, facial images and attendance records. Clear Administrator: Change all administrators to ordinary users. Restore to Factory Settings: Restore all parameter settings on the terminal to factory settings. Record: Query the attendance records of employees within a specified time range. The employee information and attendance records will not be deleted during restoration to factory 43 ...
7. Data Management 7.1 Query a Record After checkin successfully, the employee’s attendance records are saved in the terminal. You can easily query these attendance records. User ID: Enter the user ID of the employee to query. If this field is left blank, you can query the attendance records of all the employees. If you enter a user ID, you can query the attendance record of the employee with this user ID. Query Time Period: Select a time period to query, including the customized time period, yesterday, this week, last week, this month, last month, and all time periods. Start and End: When you select a customized time period, you need to input a start time and an end time. When you select other options for time period, the start ...
Page 49
iFace100 Series Product User Manual Þ Press to page # up. Or press to page down. You can query the detailed information of this record, Press ESC 2 times to return to the main menu 45 ...
8 Date/Time Setting 8 Date/Time Setting 8.1 Set Date/Time The date and time of the terminal must be set accurately to ensure the accuracy of attendance time. Press MENU once Press F2/q once and F4/u once to select Data Mgt. Press OK once Date/ Time: Set the date and time value. Date format: Set the date format which displayed on the initial interface of the terminal. The terminal supports ten date formats. Select your desired date format. 46 ...
iFace100 Series Product User Manual Display Style: This parameter is used to set the time display mode of the initial interface. Select “ON” to adopt the 24hour display mode. Select “OFF” to adopt the 12hour display mode. Bell: Set the Bell parameters. 8.2 Bell Setting ★ Lots of companies need to ring their bells to signal the start and end of work shifts, and they usually manually ring their bells or use electric bells. To lower costs and facilitate management, we integrate the time bell function into the terminal. You can set the alarm time and duration for ringing the bell based on your requirements, so that the terminal will automatically play the selected ring tone and trigger the relay at the alarm time, and stop playing the ring tone after the set duration. Tip: Only some models have the ID card options 47 ...
Page 52
8 Date/Time Setting 1. Add a bell Press F2/q 4 times to Press MENU once Press OK once select Bell. Press OK once Bell Time: This parameter is used to set a time point when the terminal automatically plays a bell ring tone everyday. Bell Date: This parameter is used to set which day the device automatically plays a bell ring tone. Ring Tone: This parameter is used to set the bell ring tone. ...
Page 53
iFace100 Series Product User Manual 2. Edit a bell Press F2/q 2 times to Edit the bell parameter like select Edit. Add a bell. Press OK once Press AB once to save and exit. 3. Delete a bell Press F2/q once to select Press <YES> to delete the Delete. current bell and <NO> to cancel Press OK once the deletion. Press AB once to save and exit.
9. Auto Test 9. Auto Test The auto test enables the system to automatically test whether functions of various modules are normal, including the screen, sensor, voice, face, keyboard and clock tests. Press MENU once Press F2/q 2 times to select AutoTest Press OK once Test Screen: The terminal automatically tests the display effect of the color TFT display by displaying full color, pure white and pure black and checks whether the screen displays properly. You can continue the test by touching the screen or exit it by pressing [Auto Test]. Test Fingerprint: The terminal automatically tests whether the fingerprint collector works properly by checking whether the fingerprint images are clear and acceptable. When the user places his/her finger in the fingered guide, the collected fingerprint image is displayed on the screen in realtime. Press [Auto Test] to exit the test. Test Voice: The terminal automatically tests whether the voice files are complete and the voice quality is good by playing the voice files stored in the terminal. You can ...
Page 55
iFace100 Series Product User Manual continue the test by touching the screen or exit it by pressing [Auto Test]. Test Face: The terminal automatically tests whether the camera works properly by checking whether the collected facial images are clear and acceptable. Press [Auto Test] to exit the test. Test Keyboard: The terminal tests whether every key on the keyboard works normally. Press any key on the [Keyboard Test] interface to check whether the pressed key matches the key displayed on screen. The keys are darkgray before pressed, and turn blue after pressed. Press [Auto Test] to exit the test. Test Time: The terminal tests whether its clock works properly by checking the stopwatch of the clock. Touch the screen to start counting, and touch it again to ...
10 USB Disk Management 10 USB Disk Management Through the [Dn/Upload] menu, you can import user information and attendance data stored in a USB disk to related software or other fingerprint recognition equipment. Press MENU once Press F2/q 2 times and F4/u once to select Dn/Upload. Press OK once ...
Page 57
iFace100 Series Product User Manual a USB disk to the terminal. Upload User Photo: Upload the JPG documents that are named after the user IDs and stored in a USB disk to the terminal, so that user photos can be displayed after the employees pass the verification. See Appendix 4 Photo ID Function. 53 ...
11 System Information 11 System Information You can check the storage status as well as version information of the terminal through the [System Information] option. Press MENU once Press F2/q 2 times and Press OK to Device F4/u 2 times to select interface, or Press Sys Info. ESC to return main Press OK once menu. Tip: Only some models have the FP Algorithm information. Press OK to Records interface, or Press ESC to return main menu. 54 ...
Page 59
iFace100 Series Product User Manual Records: The number of enrolled users, administrators and passwords are displayed on the [Records] interface; the total fingerprint storage capacity and occupied capacity as well as the total attendance storage capacity and occupied capacity are graphically displayed respectively. Device: The device name, serial number, version information, vendor and date of manufacture are displayed on the [Device] interface. 55 ...
Appendix Appendix Appendix 1 T9 Input Method The device supports to input English characters and symbols. Press related button to input text. For example, press [Name] to display the text input interface, as shown in the figure: Press once Press 5 and select 5 for Press ESC to exit the T9 latter L. Input. Press 4 and select 2 for Press AB to save and latter i return to the main menu. Repeat the process to input the other letters “nda” Tip: Press Þ to change the T9 Input from English and symbols. ...
iFace100 Series Product User Manual Appendix 2 Photo ID Function★ The Photo ID function is used to display the photo enrolled by a user or stored in a USB disk on the screen in addition to such information as the user ID and name. [Operation Steps] 1. When the photo taken by the device is used, the photo can be displayed upon successful verification. 2. To use a photo stored in a USB disk, proceed as follows: 1) Create a folder with the name of “photo” in the USB disk, and store users' photos under this folder. 2) The user photos must be in JPG format and named after their IDs. For example, for the user with the user ID of 154, the photo name must be 154.jpg. 3) Insert the USB disk into USB slot on the device, and select USB Disk Management ...
Page 62
Appendix 2) The recommended size of a user photo is less than 30 kbit. 3) The uploaded new user photo will overwrite the existing photo in related to the user ID. 4) To download user photos, select USB Disk Management > Download > Download User Photos. A folder with the name of “photo” will be automatically created on the USB disk, and all downloaded user photos are stored under this folder.
iFace100 Series Product User Manual Appendix 3 Statement on Human Rights and Privacy Dear Customers: Thank you for choosing the hybrid biometric products designed and manufactured by us. As a worldrenowned provider of biometric technologies and services, we pay much attention to the compliance with the laws related to human rights and privacy in every country while constantly performing research and development. We hereby make the following statements: 1. All of our fingerprint recognition devices for civil use only collect the characteristic points of fingerprints instead of the fingerprint images, and ...
Page 64
Appendix 1. Unlawful arrest, detention or search of citizens of the People's Republic of China is prohibited; infringement of individual privacy is prohibited. 2. The personal dignity of citizens of the People's Republic of China is inviolable. 3. The home of citizens of the People's Republic of China is inviolable. 4. The freedom and privacy of correspondence of citizens of the People's Republic of China are protected by law. At last we stress once again that biometrics, as an advanced recognition technology, will be applied in a lot of sectors including ecommerce, banking, insurance and legal affairs. Every year people around the globe suffer from great loss due to the insecurity of passwords. The biometric products actually provide adequate protection for your identity under a high security environment.
iFace100 Series Product User Manual Appendix 4 EnvironmentFriendly Use Description The Environment Friendly Use Period (EFUP) marked on this product refers to the safety period of time in which the product is used under the conditions specified in the product instructions without leakage of noxious and harmful substances. The EFUP of this product does not cover the consumable parts that need to be replaced on a regular basis such as batteries and so on. The EFUP of batteries is 5 years. Names and Concentration of Toxic and Hazardous Substances or Elements Toxic and Hazardous Substances or Elements Parts Name Pb Hg Cd Cr6+ PBB PBDE × ○ ○ ○ ○ ○ Chip resistor × ○ ○ ○ ○ ○ Chip capacitor × ○ ○ ○ ○ ○ ...