Summary of Contents for Moeller DE4-KEY-2
-
Page 1: User Manual
User Manual DE4-KEY-2 Keypad 02/00 AWB8250-1344GB 1st published 2000, edition 02/00 © Moeller GmbH, Bonn Author: Rainer Günzel Editor: Karola Großpietsch Translators: Dominik Kreuzer, Terence Osborn... - Page 2 No part of this manual may be reproduced in trademarks or registered trademarks of the any form (printed, photocopy, microfilm or owner concerned. any otherprocess) or processed, duplicated or distributed by means of electronic systems without written permission of Moeller GmbH, Bonn. Subject to alterations without notice.
-
Page 3: Table Of Contents
Contents About This Manual 1 About the LCD Keypad System overview Features of DE 4-KEY-2 Maintenance 2 Installation 3 Function and Display Key functions Status indicators 4 Operation/Displays Example for the DM 4 soft starter Appendix Dimensions Index... -
Page 5: About This Manual
About This Manual This manual contains the information you need to connect and use the LCD keypad correctly. The information in this manual applies only to the specified hardware and software versions. The following abbreviations and symbols are used in this manual: PNU: Parameter number Drive controller: Soft starter, Frequency inverter,... -
Page 7: About The Lcd Keypad
About the LCD Keypad System overview The DE 4-KEY-2 LCD keypad has the following type code: DE4 - KEY - 2 Version LCD keypad Drives Extensions generation 4, accessory The optional LCD keypad DE4 4-KEY-2 can be used to configure drive controllers to your specific require- ments. -
Page 8: Features Of De 4-Key-2
About the LCD Keypad Features of DE 4-KEY-2 The key features of the DE 4-KEY-2 LCD keypad are: Simple installation can be connected and disconnected during operation Power supply from the drive controller Display plain text LCD; additional status indicators Function keys Degree of protection IP 20... -
Page 9: Installation
Installation Plug in and remove the LCD keypad without using force. Figure 1: Mounting the DE4-KEY-2 The dimensions of the LCD keypad are specified in the Appendix on Page 19. -
Page 11: Function And Display
Function and Display Key functions Function in Menu mode Parameter mode Programming/operation mode – Change between parameter, programming, and operation mode SHIFT + PRG – – Accept parameter; depends o parameter and menu Next menu item Next parameter Increase displayed value SHIFT + Scroll down through menu Scroll down through... -
Page 12: Status Indicators
Function and Display The LED is only lit when the STOP key has been pressed, but not after initialization of the keypad, even if the device status is “Stop”. Status indicators Status indicators Mmax Fail Imax Parameter number Parameter acceptance SHPRG MENU method... - Page 13 Status indicators Segment Description Menu mode Subindex Some parameters only have subindex “0” Parameter value line Current parameter with units (if available) or main menu item Cursor Indicates, at which position a parameter value will be changed Menu/parameter text line Display (max.
-
Page 15: Operation/Displays
Operation/Displays The illustrations below are examples of the display screens and parameters of the soft starter DM 4. Names, parameter numbers and values may differ for other devices. Example for the DM Connect the LCD keypad to the DM 4 soft starter soft starter Switch on the controlled device. - Page 16 Operation/Displays 0 1 1 3 S M 4 - 3 4 0 - 7 K 5 Figure 2: Operation mode To change or view parameters, change to Program- ming mode. Press the PRG key once, to change from opera- tion mode to menu mode. If the current menu does not contain any submenus, the LCD keypad changes directly from menu mode to parameter mode.
- Page 17 Example for the DM 4 soft starter Use the cursor keys ( , , , ) to navigate within the menu and parameter modes and to find the required parameter. In menu mode, the main menu items appear on the parameter value line, which may also contain submenus.
- Page 18 Operation/Displays When the correct parameter appears on the display, press the PRG key to change from parameter mode to programming mode. The cursor now appears on the display’s parameter value line. SHPRG PARA 0 0 1 1 U - S t a r t Figure 5: Programming mode The values of all parameters allowing write access can be edited with the cursor keys.
- Page 19 Example for the DM 4 soft starter SHPRG CODE 0 0 0 6 O p e r a t . m o d e Figure 6: Display of "Operating mode" in parameter mode In programming mode, the value (0 to 3) appears on the parameter value line, and the function (e.g.
- Page 20 Operation/Displays Selection parameters include the bit parameters (e.g. status information, functio non/off). For these parameters, the name and the current numeric value (0 o 1) are displayed. To view the associated bit status text in the menu/parameter text line (e.g. On/Off, Disable/ Continue), press PRG.
-
Page 21: Appendix
Appendix Dimensions... -
Page 23: Index
Index Default display parameter ..........13 Displays ................13 Drive controller ..............3 Features of DE 4-KEY-2 ........... 6 Frequency inverter ............3 Function and display ............9 Init .................. 13 Installation ................ 7 Key ................... 9 Key functions ..............9 Main menu item ............. - Page 24 Saving ................5 Selection parameter ............16 Selection texts ..............15 Servo controller ..............3 Soft starter ................ 3 Status indicators ............10 Sub-index ............... 10 Submenu ................ 15 System overview .............. 5 Type code ................. 5...
Need help?
Do you have a question about the DE4-KEY-2 and is the answer not in the manual?
Questions and answers