Page 1
Advanced Driving Assistance System This product is a driving assistance system. Since any accident while using K15 shall not be the responsibility of the manufacturer, please drive safely according to the purpose of this product. USER’S Manual...
TABLE OF CONTENTS Safety advice Products and Features Explanntions of the device Components Installation instruction and calibration Installation location by vehicle type Features of the product Setting Function description Firmware upgrade Use for viewer program...
Warning for potential serious accidents or damages/injuries due to violation of instructions Do not put the product in any heating devices(stove, microwave oven, etc.) to dry when it is wet. It can cause deformation or malfunction for which free services are not available. Do not use chemical detergents(benzene, thinner, alcohol, etc.) to clean the product.
Page 4
Caution Items to check before use When driving on a road where there is no lane or it is difficult to see the lane When the lane is not continuous When GPS reception is not good in a busy city or due to a natural disaster When the sight is not good due to extreme weather (rain, snow, fog, etc.) When there are problems with tunnel entrances/exits or the headlights while driving at night When there is no light or the outside lighting changes abruptly...
Products and Features Safe driving assistance device It is a cutting-edge product with FCWS, LDWS and Drive Recorder features to deliver essential information for safe driving. GPS receiver: It receives GPS signals, sets the operation speed and saves the time and location of the accident while saving the video.
Explanntions of the device Remote receiver POWER LED RESET Micro SD card slot Angle adjusting lever USB type DC input, Turn signal, Video Out and GPS connection Angle fix bolt CAMERA LENS Security Warning LED When porver is on, LED turns on. Direction indicator connecting port: Connect the cable that comes with the product.
Components Advanced Driving Assistance System Micro Adapter USER’S Manual DC(12V~24), GPS, Double-sided Main device & Manual Micro-SD Card/ Romte Turn Signal, tape / Cable Base bracket Adapter Video Out cable Mount Check whether all components are included as shown above after purchasing the product. Contact the store of your purchase if any component is damaged or does not perform properly.
• Please check the necessary components enclosed in the product kit and follow the installation instruction step by step. • This manual describes how to install K15 in a car by car type: passenger car, SUV, Bus and truck. For buses and trucks, except for the installation position, the procedures are similar with those for passenger cars.
Page 9
Vertical Installation (how to attach/where to attach/angle) for passenger cars and SUVs For perfect installation of K15 please make sure to follow the details of this manual step by step. Install this product with the car’s engine turned off. 2. Stick the base bracket on 3.
Page 10
Installation instruction and calibration Installation 8. It needs to connect the monitor screen to get video-out from the device, a yellow horizontal line appears on it. Refer to the pictures below for indoor and outdoor installation, respectively. Indoor installation: As shown in the picture, place the product so that the blue line on the monitor is placed at the point where the virtual red lines cross and fix it with the angle adjusting bolt.
Page 11
Installation instruction and calibration 9. When the previous steps are completed, power up the engine to provide power to the product. Check if the monitor connected for video-out function is normally working. Step 1: Selecting car model Calibration lines Select car model. Car models: car, SUV, large van, bus (see page 17 in the manual) Horizon Step 2: Adjust horizontal and calibration line...
Page 12
Installation instruction and calibration Installation instruction for the DC Input cable, the turn signal cable and video out cable GPS Connect Red : ACC USB Type Connect White : T/C Left connecting cable Video Out Connect Yellow : T/C Right Black : GND How to connect direction indicator cable When the direction indicator is connected with the cable, the alert won’t go off when changing the lane...
Installation location by vehicle type Installation Position 4 car types are available for installation. Passenger car Install the product in top center of the windshield. Make sure the product is aligned horizontally. Select car mode: Sedan Installation Position SUV, mini van, small truck Install the product in top center of the windshield.
Page 14
For trucks and buses, do not forget to install a power stabilization cable (a 24V to 12V adapter). K15 can be operable in the voltage range of DC 12V to 24V but it doesn’t necessarily mean that the product can operates in all buses and trucks.
FCWS(Forward Collision Warning System) K15 is a driving assistance device that detects forward collision and lane deviation risks by obtaining the image of the road in front of the car through its internal camera and analyzing the data real time, and gives warnings to prevent any possible accident that can be caused by the driver’s reckless or drowsy driving.
Page 16
After K15 booted up, when an internal G-sensor (a shock-detection sensor) detects an event, K15 automatically records the image for 40 seconds. K15 also records the time and location of an event as well as the image. Regardless of the amount of force imposed on the car, you can record the image...
Setting You can set all the functions and modes of K15 with the remote control enclosed in the package. VOL: Volume control How to control volume : . Press Vol. button You will hear a voice “volume control mode”. ( Arrow key) You can control the volume with button.
Page 18
Setting FCWS FCWS On/Off : If K15 operates incorrectly while FCWS, you can start by pressing button You will hear “FCWS On/Off”. TTC (Time To Collision) : This is to calculate predicted time to collision and give an alarm in advance.
Page 19
Setting LDWS LWT(Left Warning Time) : alarm timing for left line deviation This is to set the timing of an alarm for a left line deviation. If you feel that the timing of the alarm is too fast or late, you can change the alarm timing for every 10cm.
Page 20
“55mph”. Stop pressing when you hear the speed you want and wait for a moment it is automatically set. CR(Calibration Reset) : 1. If K15 operates incorrectly while FCWS and LDWS, you can start recalibration by pressing button You will hear “calibration reset”.
Page 21
Setting B.Box G-Sen(G-sensor shock): 1. This is to set the impact level that a G-sensor installed in K15 detects. Press button then you will hear “impact level setting”. 2. You can change the setting with button Every time the button is pressed, the voice message changes as follows: “sensitive detection”...
Function description Function description Once the car engine started, K15 is provided with power and red and blue LEDs are on. → Make sure that K15 is connected with the provided power cable. After booting, K15 starts operating with the recorded message.
Function description Event recording Event recording records the images of an impact (for 40 seconds) that the internal G-sensor detects and stores the recorded file as “*.avi” format. The file is stored in the “EVENT” folder in the Micro SD card. In event recording, sensitivity of the G-sensor can be set as three levels –...
Page 24
Video-out and turn signal connection (the cable can be offered at a cost.) With the Video-out function, you can check video images real time on a screen device by connecting K15 USB port and the import port of the screen via the Video-out cable additionally provided on your option.
Page 25
K15 receives GPS time data in regular interval and synchronize its time with the received time in order to record exact time of any event. Therefore, once time is set, the RTC function makes K15 work in accordance real time.
Firmware upgrade Read the followings carefully before upgrade. (contact the stores for upgrade files.) - Step 1: Copy the upgrade files onto the root directory of Micro-SD card. - Step 2: Turn the power OFF and insert Micro-SD card. - Step 3: Connect the power cable to the main body and turn the power ON. - Step 4: Wait for about 10~20 sec.
Viewer program (PC Viewer) Run BlackBox viewer installation file in Micro-SD card and install by following the instructions. When installation is complete, click on the Open icon to open the viewer program. PC viewer screen Select normal recording Select impact recording Select front/rear video Select forced(manual) recording Front video...
Page 28
Viewer program (PC Viewer) Switch windows Switch Front/Rear Switches front/rear and plays the video. Select video folder to save Maximize Close program the screen size Minimize 20140001 0231_M_001.avi the screen size Nomal : Normal recording video list Even t : Impact recording video list 20140002 0232_M_002.avi Manual : Manual(forced) recording video list 20140003 0233_M_003.avi...
Page 32
Specifications Model Main features FCWS, LDWS, Drive Recorder Capacity Micro SDHC Class10 (supports up to 32GB) Camera 2M HD 1280 x 720 External GPS Operating volt. DC 12V ~ 24V Operation/storing 32℉ ~ 140℉ / 14℉ ~ 158℉ temperature...
Need help?
Do you have a question about the K15 and is the answer not in the manual?
Questions and answers