Summary of Contents for Trimm Technologies UR8J2-4 Series
-
Page 1: Installation Guide
Installation Guide UltraRAID™ Family UR8J2-4xxx – Ultra Rack SCSI-3 Ultra 2 (Low Voltage Differential – LVD) UT8J2-4xxx – Ultra Tower SCSI-3 Ultra 2 (Low Voltage Differential – LVD) Part Number 8519184-0000 Rev: B... - Page 2 Part Number 8519184-0000 Rev: B...
-
Page 3: Table Of Contents
Table of Contents: UltraRAID Family Text: Description Page General Information: ………………………………………………………..1 Description: …………………………………………………………………..1 First – Unpack, Inspect and Check: ………………………………………..1 Specifications: ………………………………………………………………..2 Dimensions: ………………………………………………………………..2 Power Supply: ……………………………………………………………..2 Cooling: …………………………………………………………………..2 Environment: ……………………………………………………………..2 Drive Type(s) Supported: ………………………………………………..…..3 Host Connection(s): …………………………………………………………..3 Convert 2 x 4 Configuration to a 1 x 8 or vice versa: ........4 Installation Sequence: ………………………………………………………... -
Page 4: General Information
General Information Congratulations on your choice of a Trimm Technologies Enclosure. The UR8J series of enclosures are intended for rack-mounted applications. The UT8J series of enclosures are tower types for desktop (deskside) applications. Both types of enclosures support up to eight (8) 3.5” SCSI hard drives. The drives are to be mounted in drive canisters (modules), which accommodate standard or low profile SCA-2 style drives. -
Page 5: Specifications
Specifications: Dimensions: Enclosure: (external dim.) (Rack Style) (Tower Style) Height: 5.25” 13.34cm 20.0” 50.80cm Width: (w/foot) 12.05” 30.61cm Width: (w/o foot) 19.0” 48.26cm 7.0” 17.78cm Depth: 22.0” 55.88cm 24.0 60.96cm Drive Canister (Module): (Internal dim.) Height: 1.65” 4.19cm (max to permit airflow) Width: 4.03”... -
Page 6: Drive Type(S) Supported
Drive Type(s) Supported: • 3.5” full-size (1.65” H) and low profile (LP) (1.00” H) (25mm). • Hard drive rotational speeds up to 10,000 RPM. • Using a Single Connect Attach (SCA-2) type connector (80pin). • Low Voltage Differential (LVD) interface, with transfer abilities up to SCSI-3 Ultra 2, at 40 Mhz for data transfer rates up to 80 MB/s (wide interface). -
Page 7: Convert 2 X 4 Configuration To A 1 X 8 Or Vice Versa
Figure 1 Connection Illustration Convert 2 x 4 Configuration to a 1 x 8 or vice versa: To convert either way, either connect or disconnect a jumper cable between the 2 connector for the SCSI A and SCSI B connectors at the rear of the enclosure (reference Figure’s 1and 4). For a 1 x 8 configuration, install the a SCSI jumper cable between the second connectors for the SCSI A and SCSI B connectors. -
Page 8: Installation Sequence
Installation Sequence: • Unpack & Inspect • Install Enclosure in Rack (Mount Enclosure) (rack style) / Install Feet (tower style) • Install End Caps (Rack Style) • Mount Drives in Canisters (Drive Modules) • Install Canisters in Enclosure • Set Base Addresses for each Host Channel (in) •... -
Page 9: Install/Remove End Caps (Rack-Mount Enclosure Only)
Install/Remove End Caps (Rack-Mount Enclosure only) The end caps are dress items, which mount on the rail flanges at the ends of the enclosure. The caps snap in place with a notch at the bottom of the caps. To snap the caps in place, insert the top notch in place first and then push the bottom in until the flexible flange at the bottom is captured in the mating indent. -
Page 10: Canister Into Enclosure
Canister into Enclosure Light pipes (LED Outputs) Lever Insert the canister with the drive in place in a manner similar to the above illustration. The canister has slides on the sides to help guide the canister into position, The canister has a lever at the front which cams the canister into the final closed position. -
Page 11: Fan (Auxiliary Blower) Install/Remove
Base Address Switches Host Connections Power Supply Figure 4 Rear View Fan (Auxiliary Blower) Install/Remove To remove the fan assembly (Reference Figure 4), undo the thumbscrew and pull the assembly to the rear, by pulling on the thumbscrew. To install, push assembly into place and tighten the thumbscrew. -
Page 12: Figure 5 Saf-Te Daughter Board Option Connected To Alarm Board
2. The mid-plane (backplane) board is located approximately in the middle of the enclosure and connects the drives to the host connection board. This board is not a FRU and is only repaired by returning the enclosure to Trimm. Generally, this board does not contain any active components. -
Page 13: Field Replacement Units (Fru's)
Field Replaceable Units FRU’s Description Trimm Part Number Power Supply, 350W (PFC) 5417240-0100 Power Supply, 350W (non-PFC) 5420009-0100 Drive Canister (2 each), 5417239-002* Drive Canister (8 each), 5417239-008* End Caps (pair), 5417418-010* Alarm Board (standard JBOD) Assembly 5418868-0100 Alarm Board (Castle UR16R JBOD) Assembly 5419533-0000 Saf-Te Board Assembly 5418887-0100... - Page 14 Saf-Te Option Daughter Board Part Number 5418887-0100 Alarm Board Assembly Part Number 5418868-0100 Terminator, SE/LVD Multimode Part Number 5417847-0100 Cable, multimode (external) Part Number 5417823-0100 = 1 foot Part Number 5417823-0200 = 3 foot Part Number 5417823-0300 = 10 foot Part Number 5417823-0400 = 25 foot Page 11 of 14 Part Number 8519184-0000 Rev: B...
-
Page 15: Certifications, Cautions And Warranty
The integrator is responsible for End Product testing and agency verifications. Do not use the enclosure in any manner other than the intended use/purpose as advertised by Trimm Technologies. The enclosure meets the requirements of the following agencies: - Underwriters Laboratories, Recognized Component –... -
Page 16: Warranty
(dropping, stacking, etc.). Warranty: Trimm Technologies warrants its range of products to be free from defects in material and workmanship for a period of ONE YEAR from date of manufacture. The company makes this warranty only to purchasers who acquired the product direct from the company, its authorized dealers or reps, or others who are specifically authorized by the company to sell such products. -
Page 17: Technical Support
Technical Support If you have any problems or need advice on future expansion / products contact Trimm Technical Support via: Mailing Address: Trimm Technologies, Inc. Trimm Technologies Limited 350 Pilot Road Millennium Way East Las Vegas, Nevada 89119 Phoenix Centre... - Page 18 Trimm Technologies, Inc. Trimm Technologies LTD. 350 Pilot Rd. Millennium Way East Las Vegas, Nevada 89119 USA Phoenix Centre Phone: 702-263-2310 Nottingham, England NG8 6AR 702-260-3443 Phone: +44 (0) 115-951-9951 http://www.trimm.com Fax: +44 (0) 115-951-9985 Part Number 8519184-0000 Rev: B...
Need help?
Do you have a question about the UR8J2-4 Series and is the answer not in the manual?
Questions and answers