EnvironmentalLights.com RGB1 User Manual

Rgb led touch controller (remote control-1 zone) - 12 or 24 vdc

Hide thumbs

Table Of Contents

(Remote Control-1 Zone) - 12 or 24 VDC

The RGB LED Touch Controller (RGB1) is an easy way to mix colors seamlessly in real-time,

using any 12 or 24 volt RGB LED product. Customize the color of your RGB LED product by

simply touching the color wheel. Apply the correct DC voltage to the inputs and the controller

will generate pulse dimming signals on three separate output channels (red, green and blue).

Output is 12 or 24 VDC, matching the driver you use. Pre-programmed with 11 modes, this three

channel RGB LED Touch Controller is ready to use.

Features

 RF hand-held remote controller lets you select operating modes and custom colors:

 Touch sensitive color wheel allows real-time custom control of colors. Simply touch the

desired color on the color wheel and your RGB LED lights will sync to match the color.

 11 pre-programed modes:

o Static red, green, yellow, blue, magenta, cyan, and white.

o RGB color change mode.

o Seven color change mode (red, green, yellow, blue, magenta, cyan, and white).

o RGB color fade mode.

o Seven color fade mode (red, green, yellow, blue, magenta, cyan, and white).

 Remote controller works through walls. Over 100 foot range in benign electromagnetic

environment.

 High output frequency enables a large color spectrum and pulse width modulation

dimming.

 Power off memory function.

RGB LED Touch Controller

Part No. RGB1

11235 West Bernardo Court, S uite 102

S an Diego, CA 92127

888-880-1880

Fax: 707-281-0567

EnvironmentalLights.com

Table of Contents

Need help?

Do you have a question about the RGB1 and is the answer not in the manual?

Questions and answers

Summary of Contents for EnvironmentalLights.com RGB1

Page 1 (Remote Control-1 Zone) - 12 or 24 VDC Part No. RGB1 The RGB LED Touch Controller (RGB1) is an easy way to mix colors seamlessly in real-time, using any 12 or 24 volt RGB LED product. Customize the color of your RGB LED product by simply touching the color wheel.
Page 2 -: Increases or decreases the speed of dynamic modes.  : Increases or decreases the brightness when in static modes (12 levels).  : Indicates signal transmission when green. RGB1 RF touch sensitive remote Copyright EnvironmentalLights.com All Rights Reserved 10/20/13...
Page 3  Hotels, restaurants, office buildings, homes and casinos, wine cellars, bars, home entertainment centers. Detailed Wiring Instructions EnvironmentalLights.com provides detailed wiring instructions for our LED linear lighting (flex strips, superflat rope, modules and rigid strips.) In addition, we provide the design criteria charts that tell you how many feet, LEDs, modules, reels or other units you can put on a) each branch and b) each drive unit.
Page 4 With these amplifiers as building blocks, you can build an installation that is very large. Refer to the diagrams at the end and contact us if you are unsure how to engineer the system. Copyright EnvironmentalLights.com All Rights Reserved 10/20/13...
Page 5 RGB LED Touch Controller RGB strips, superflat rope, (4 wires: red, green, or modules blue, common) RGB1 Do not exceed the product's (2 wires, +V & ground) specified branch length limit. 12 or 24 VDC Driver Do not exceed the power rating of the lowest-rated driver, amp or controller.
Page 6 (4 wires: red, green, superflat rope, blue, common) (4 wires: red, green, or modules blue, common) RGB1 AMP4 (2 wires, +V & ground) (2 wires, +V & ground) 12 or 24 VDC Adapter 12 or 24 VDC Driver 24 watts is adequate...