Related Manuals for GVision Legacy
Summary of Contents for GVision Legacy
- Page 1 TouchScreen Controller Installation Guide VERSION : 2.5 DATE : 2005.12.09 ════════════════════════════════════════════════...
-
Page 2: Table Of Contents
Table of Content Chapter 1. TOUCH SCREEN CONTROLLER ………………………………………….. About this Document………………………………………………………………………………… Touch Screen Controller Components…………………………………………………………….. Hardware System Requirements…………………………………………………………………… Chapter 2.CONTROLLER FEATURES …………………………………………………... Serial Controller Features…………………………………………………………………………… PS/2 Controller Features……………………………………………………………………………. USB Controller Features……………………………………………………………………………. Chapter 3. TOUCH SCREEN CONTROLLER HARDWARE INSTALLATION 5 Wires Resistive USB Touch Screen Controller Hardware Installation………………………. 5 Wires Resistive Serial Touch Screen Controller Hardware Installation………………………. -
Page 3: Chapter 1. Touch Screen Controller
Chapter 1. TOUCH SCREEN CONTROLLER About this Document The information in this document is subject to change without notice. Touch Screen Controller Components • Enhanced anti-noise SMD multi-layered controller board with 2 attached cables • Serial controller with a keyboard power tap cable •... -
Page 4: Chapter 2.Controller Features
Chapter 2. CONTROLLER FEATURES Serial Controller Features (a) Hardware Specifications +5VDC ( Maximum 150mA, typical current depend on specified panel, 50mV Power Requirements peak to peak maximum ripple ) 0 to 60 ℃ Operating Temperature -40 to 80 ℃ Storage Tempeture 95% at 60 ℃... -
Page 5: Ps/2 Controller Features
PS/2 Controller Features (a) Hardware Specifications Power Requirements +5VDC ( Maximum 30mA, typical 15mA, 50mV peak to peak maximum ripple ) 0 to 60 ℃ Operating Temperature -40 to 80 ℃ Storage Tempeture 95% at 60 ℃ Relative Humidity Protocol Standard 2 button PS/2 Mouse. -
Page 6: Usb Controller Features
USB Controller Features (a) Hardware Specifications Power Requirements +5VDC ( Maximum 100mA ) 0 to 60 ℃ Operating Temperature -40 to 80 ℃ Storage Tempeture 95% at 60 ℃ Relative Humidity Protocol Standard USB Mouse. Report Rate Minimum 160 PPS (Point per Second) Response Time Maximum 35 ms Pin Out Definition... -
Page 7: Chapter 3. Touch Screen Controller Hardware Installation
Chapter 3. TOUCH SCREEN CONTROLLER HARDWARE INSTALLATION 5 Wires Resistive USB Touch Screen Controller Hardware Installation This chapter discusses how to install your 5 wires resistive serial touch screen controller, follow the directions starting on the next section to install the controller to your computer. IMPORTANT: Before connecting the touch screen controller to your computer system, Be sure that the computer system is turned off. - Page 8 5. Turning On Your Computer System Before you turn on your computer system, ensure that all cables are connected properly and that the controller is properly mounted. Be sure to tighten all cable connector screws. To start up your system: •...
-
Page 9: Wires Resistive Serial Touch Screen Controller Hardware Installation
5 Wires Resistive Serial Touch Screen Controller Hardware Installation This chapter discusses how to install your 5 wires resistive serial touch screen controller, follow the directions starting on the next section to install the controller to your computer. IMPORTANT: Before connecting the touch screen controller to your computer system, Be sure that the computer system is turned off. - Page 10 5. Turning On Your Computer System Before you turn on your computer system, ensure that all cables are connected properly and that the controller is properly mounted. Be sure to tighten all cable connector screws. To start up your system: •...
-
Page 11: Wires Resistive Ps/2 Touch Screen Controller Hardware Installation
5 Wires Resistive PS/2 Touch Screen Controller Hardware Installation This chapter discusses how to install your 5 wires resistive PS/2 touch screen controller, follow the directions starting on the next section to install the controller to your computer. IMPORTANT: Before connecting the touch screen controller to your computer system, Be sure that the computer system is turned off. - Page 12 5. Turning On Your Computer System Before you turn on your computer system, ensure that all cables are connected properly and the controller is mounted properly. Be sure to tighten all cable connector screws. To start up your system: • Turn on your computer system. •...
-
Page 13: Wires Resistive Serial Touch Screen Controller Hardware Installation
4 Wires Resistive Serial Touch Screen Controller Hardware Installation This chapter discusses how to install your 4 wires resistive serial touch screen controller, follow the directions starting on the next section to install the controller to your computer. IMPORTANT: Before connecting the touch screen controller to your computer system, Be sure that the computer system is turned off. - Page 14 4. Turning On Your Computer System Before you turn on your computer system, ensure that all cables are connected properly and that the controller is properly mounted. Be sure to tighten all cable connector screws. To start up your system: •...
-
Page 15: Wires Resistive Ps/2 Touch Screen Controller Hardware Installation
4 Wires Resistive PS/2 Touch Screen Controller Hardware Installation This chapter discusses how to install your 4 wires resistive ps/2 touch screen controller, follow the directions starting on the next section to install the controller to your computer. IMPORTANT: Before connecting the TouchScreen Controller to your computer system, Be sure that the computer system is turned off. - Page 16 4. Turning On Your Computer System Before you turn on your computer system, ensure that all cables are connected properly and the controller is properly mounted. Be sure to tighten all cable connector screws. To start up your system: • Turn on your computer system. •...
-
Page 17: Chapter 4. Software Installation
Chapter 4. SOFTWARE INSTALLATION This chapter discusses how to install the TouchScreen Driver software. The TouchScreen Drivers CD-ROM provides driver software that allows your TouchScreen to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: Volume: TSCD06 USB Model Drivers \ USB... - Page 18 Touch Screen Controller List … USB-R5W- HT580 Internal 5 wires resistive serial controller (w/o case) … COM-R4W-MT066 Internal 4 wires resistive serial controller (w/o case) … COM-R4W-6002 External 4 wires resistive serial controller (w/ case) … COM-R5W-MT566/HT271 Internal 5 wires resistive serial controller (w/o case) …...
-
Page 19: Chapter 5. Driver Installation
Chapter 5. DRIVER INSTALLATION Windows XP This section discusses how to install the driver and calibrate the TouchScreen for Windows XP. Note: You must have administrator access rights to install the driver. To install the TouchScreen Driver: • Inser the TouchScreen Drivers CD-ROM in your computer’s CD-ROM drive •... -
Page 20: Windows 2000
Windows 2000 This section discusses how to install the driver and calibrate the touchscreen for Windows 2000. Note: You must have administrator access rights to install the driver. To install the TouchScreen Driver: • Inser the TouchScreen Drivers CD-ROM in your computer’s CD-ROM drive •... -
Page 21: Windows Nt 4.0
Windows NT 4.0 This section discusses how to install the driver and calibrate the TouchScreen for Windows NT 4.0. Note: You must have administrator access rights to install the driver. To install the TouchScreen Driver: • Inser the TouchScreen Drivers CD-ROM in your computer’s CD-ROM drive •... -
Page 22: Windows 98
Windows 98 This section discusses how to install the driver and calibrate the TouchScreen for Windows 98. To install the TouchScreen Driver: • Inser the TouchScreen Drivers CD-ROM in your computer’s CD-ROM drive • Click Start > Run • Click the Browse button to locate the Setup.exe program on the path “\COM\WIN98” of the CD-ROM. •... -
Page 23: Windows 3.1
Windows 3.1 This section discusses how to install the driver and calibrate the TouchScreen for Windows 3.1. To install the TouchScreen Driver: • Inser the TouchScreen Drivers CD-ROM in your computer’s CD-ROM drive • Click File > Run on the Desktop Menu. •... -
Page 24: Linux
Linux This section discusses how to install the driver and calibrate the TouchScreen for Linux . 1. Serial Touch Screen Controller Driver Version 2.0.0 The TSCOM for Linux SetupPack Version 2.0.0 required the X Window System using XOrg version 6.4.x / XFree86 version 4.1 or later. - Page 25 Installation manually (for expert) We recommand that you using the Setup Wizard to complete the install, refer to Installation using Setup Wizard section for detail. The followings describe how to complete the install manully: 1. Login as root. 2. Checking the X Window System Version. To get the X Window System Version by running the following: X -version Write down the X Window System Version that you using, it's required when installing the Driver...
- Page 26 ----------------------------------------------------------- ------------------------------------------------ Extra the the Driver Package file by running the followings (replace the sourcePath to the path of the Driver Package file, and replace the xxx to set the filename to the Driver Package Filename that you want to install): cd /etc/TSCOM gzip -d <...
- Page 27 Option "ScreenNo" "0" Option "SendCoreEvents" "yes" EndSection Section "InputDevice" Identifier "TSCOM_Calibration Driver "tscomxp" EndSection Note: (1) The instructions above are case-sensitive. (2) The instructions above are for a touchscreen connected to COM1, the Option Device specifies the COM port the touchscreen is connected to. The following describe how to use: Use Option Device /dev/ttyS0...
- Page 28 Right Button Function The TSCOM Touchscreen supported two Right Button Function Mode, one is Manual Mode , the other is Autometic Mode , see the followings for detail information. · Manual Right Button Mode To enable the Manual Right Button Function, run the tscom_rightbutton program in in the /etc/TSCOM...
- Page 29 Toggle-Off time ( RightButtonAutoETime), the Touchscreen stay in Right Button Mode until you lift-off from the Touchscreen. If the Toggle-Beep Mode (RightButtonAutoBeep) is set to 1 (Yes), the Touchscreen will beep when it autometic toggle-on/off the Right Button Mode. Touch Beep Function To enable/disable the Touch Beep Function, edit the tscom-config file in the...
- Page 30 Option "Emulate3Buttons" Option "Emulate3Timeout" "50" Option "SendCoreEvents" "yes" Option "TouchBeepMode" "0" Option "TouchBeepVolume" "100" Option "TouchBeepPitch" "2468" Option "TouchBeepDuration" "20" EndSection Section "InputDevice" Identifier "TSPS2_Calibration” Driver "tsps2xp" EndSection Note: • The instructions above are case-sensitive. • Checkout that you don’t have two drivers configured which use the same PS2-device ("/dev/psaux"). •...
-
Page 31: Chapter 6. Uninstall Touch Screen Driver
Chapter 6. UNINSTALL TOUCH SCREEN DRIVER This section discusses how to uninstall the TouchScreen Driver for Windows. To uninstall the TouchScreen: • Click Start > Programs > TouchScreen V.x.x.COM > TouchScreen Uninstall V.x.x.COM ( where x.x is the Version of TouchScreen Driver ) •... - Page 32 Duration: Adjust the time of feedback sound Default setting: Silence ════════════════════════════════════════════════...
- Page 33 Mouse Speed Function: Mouse Speed sets the speed of mouse Detail: It can adjust horizontal speed and vertical speed of mouse Default setting: Bypass Mode -- Enable Power Save Function: Power Save is to set the time of power down Default setting: Disable Power Down Function Calibration Function: Calibration is to set the corresponding location with different VGA mode resolution...
Need help?
Do you have a question about the Legacy and is the answer not in the manual?
Questions and answers