Advent Controls DE1.05 User Manual
  1. Manuals
  2. Brands
  3. Advent Controls Manuals
  4. Intercom System
  5. DE1.05
  6. User manual

Advent Controls DE1.05 User Manual

Quad band gsm door entry intercom /open-on-call access control with text alert & auto-dia
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
7
SMS Command Set Summary
Command
Action
ADD
number
.
CALL
LIST
ANY
CALLNUM
number
CLEARALL
CLOSE
CONNECT
NONE
CL
CSQ
CTIME
<seconds>
.
CUSTOM
DIAL
number
EXIT
DIS
EN
INPUT
DIS
EN
INLEVEL
OPEN
CLOSE
LIST
MASTER
number
.
MUSER
DISABLE
ENABLE
OFF [as CLOSE}
OPEN/ON
OPEN/ON
<seconds>
OPEN/ON
<minutes>m.
PRGSIM
PSMS
Enable
Disable
QUERY/QNUM
number
.
REJECT
ALL
NEVER
REM
number
.
RESET
RLYMODE
PULSE
TOGGLE
RLYTIME
<seconds>
RLYTIME
<minutes>m
.
RSMS
Enable
Disable
RTIME
<seconds>
SILENCE
<seconds>
SMS
number,
interval (days)
SMS
OFF
STATUS
TEXTNUM
<master>
number
TEXTRES
DIS
EN
VOLUME
<vol>
Developed and Manufactured by Advent Controls Ltd, Liverpool, UK
Comments
Add User Number
NONE
Call Handling
Add Autodial Call Number
Also clears MASTER
Deactivate Relay
OP
Connect Call Condition
Get RSSI
Set Call Maximum Time Limit
Custom input message
Dial Number on Receipt
Exit Switch Enable
Input Trigger Enable
Input Edge Trigger Setting
List All Numbers
Add Master User
Treat all users as Master
Deactivate Relay
Activate Relay
Open for <seconds> seconds
Open for <minutes> minutes
Purge Inbox
Power Up Text Alert
Find Number in Memory
OPEN
Call Handling
Remove Number
Reset Settings to Defaults
RING
Relay Mode Toggle/Pulse
(default 3s)
relay time in minutes
Reset Text Alert (Network)
Maximum Ring Time
Maximum Line Silence Time
.
PAYG Keep Alive
(switch off KA Text)
Get Relay and Input Status
.
Input Trigger Text Numbers
Result Acknowledgement
Speaker Volume 1-9
QUAD Band GSM
Door Entry Intercom
DE1.05/Firmware 2.11DE
Open-on-Call Access Control
with Text Alert & Auto-Dial
for GSM850MHz, GSM900MHz
DCS1800MHz & PCS1900MHz
www.adventcontrols.co.uk

Advertisement

Table of Contents
loading

Summary of Contents for Advent Controls DE1.05

  • Page 1 Text Alert & Auto-Dial STATUS Get Relay and Input Status TEXTNUM <master> number Input Trigger Text Numbers TEXTRES Result Acknowledgement for GSM850MHz, GSM900MHz VOLUME <vol> Speaker Volume 1-9 DCS1800MHz & PCS1900MHz Developed and Manufactured by Advent Controls Ltd, Liverpool, UK www.adventcontrols.co.uk...

  • Page 2: Table Of Contents

    EMC/EMI Compliance Statement: CE Mark Declaration of Conformance Manufacturer's Disclaimer Statement: The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular purpose of this document.

  • Page 3: Introduction

    Installation Introduction The Advent Controls GSM Door Entry Intercom allows callers to your property to speak to you no matter where you are. When connected to a door or gate you can grant a visitor access using your telephone. Using the GSM network the unit requires only power to operate making installation simple.

  • Page 4: Operation

    User Numbers When using a Pay As You Go (PAYG) SIM card, to avoid SIM card deactivation, the system can periodically send a SMS text message to keep the SIM active. Ensure the SIM card has User numbers are only able to operate the relay output. This can be via SMS text or by call- sufficient credit to make a call or text (even if the call goes unanswered).

  • Page 5: Command Message Format

    Command Message Format Changing the Maximum Line Silence Time To operate the system a master GSM phone is used to send SMS text messages to the system The maximum time for which a silent call will remain connected is set using the SILENCE telephone number.

  • Page 6: 2.4 Allowing Master Control For All Users

    Input Change State Level Using the PIN for Master Setup The INLVL sets the active state of the input for sending the change state text message. For The Master Number can also be set up using the PIN. This is only possible for the first master example, if the user requires a message to be sent when the input is closed (GND), then the number that is added to the system.

  • Page 7: Finding A Number In The Memory

    To receive the list of numbers the LIST command is used. The master phone must send the When sent with additional time information the relay is activated for however many sec- following SMS text message to the system: onds or minutes specified. List e.g.

  • Page 8: Relay Operation/Access Control

    Input/Output Status Message Relay Operation/Access Control To determine the current status of the input terminal and output relay the STATUS command Enabling Any Number and Disabling Open-on-Call is sent to the system telephone number by a master phone as follows: The system can be setup to allow any number to operate the relay output.

Table of Contents