Subscribe to Our Youtube Channel
Summary of Contents for WarmlyYours TempZone
- Page 1 Installation Manual for your TempZone™ Electric Radiant Floor Heating System (Twin Conductor) Free Design Service • 24/7 Installation Support • No Nonsense™ Warranty • (800) 875-5285 • www.WarmlyYours.com...
-
Page 2: Understanding The System
The EasyStat™ has an in floor traffic during the flooring installation. When WarmlyYours floor heating systems are installed on sensor just like the SmartStat™, a concrete slab, we strongly recommend adding a layer Never Cut The Heating Element but requires no programming. - Page 3 Circuit Check (Not a substitute for an OHM meter) Off-Cuts Of Cardboard Or Carpet Scraps This device is offered in every order from WarmlyYours and is a continuity checker that you connect to the cold lead wires before installation of the flooring material.
- Page 4 If C. Starting Point: you have made any alterations to your floor plan, contact WarmlyYours to have Indicates where the Heating Roll(s) starts. your Installation Plan updated.
- Page 5 Warmlyyours Floor Heating System. The Heating Roll A. Heating Element Relay Contactor or Power Modules B. Fiberglass Mesh C. Tape (not required for all systems) D. Cold Lead Wire Systems installed in large spaces will most likely require a Relay E.
- Page 6 The complimentary Installation Plan provided by the Mark the appropriate circuit breaker reference label WarmlyYours team is very important. It shows the indicating which branch circuit supplies the circuits to By cutting only the Mesh (see Photo A), you can move recommended placement of your Heating Roll(s) for those electric space heating cables.
- Page 7 One Good Turn Deserves Another Step Turn Step Turn with Flip Over Working Experience is the Key around Obstacles As you begin to work with the Heating Start Start Panels, you will become more comfortable Special circumstances will require the with the product.
- Page 8 1. Before starting installation. Three (3) Ohm Readings should be taken for each roll of WarmlyYours TempZone at each 2. After securing the Heating Roll(s) in place on the subfloor. stage of the installation and recorded in the table below.
- Page 9 Output Unit W : 135 Puissance de l’unite 4. Using a wirenut, attach black wire to upper black S/NO C/O INDIA Made by Thermopads Pvt. Ltd. for WarmlyYours.com Inc. wire labeled: “Load ”. Red (240) or Yellow (120) Wires 5. Using a wirenut, attach the ground wire of heating roll to the ground wire in the wallbox.
-
Page 10: Installer's Guide
If this location has changed, call edges or pointed objects that might damage rest. (Cabinets, toilet base, etc.) WarmlyYours to determine if this will require the Heating Element. Mark the position of the sensor (if one is to a new Installation Plan. -
Page 11: Materials And Tools Required
SLU. For best results, we recommend a 1”- 1.5” maximum distance between the Please call WarmlyYours at (800) 875-5285 if the roll does not provide the specified heating cable and the top of the floor. - Page 12 Registration Card. recommended by the manufacturer before cross the cold leads if necessary. Two-step method: powering-up the WarmlyYours electric 3. Run all cold lead wires beside the mats radiant heat system. 1. Apply a 1/8” skim coat with a flat rubber...
- Page 13 This is recommended to increase efficiency, but is not mandatory. Please call WarmlyYours at (800) 875-5285 if the roll does not provide the specified For best results, we recommend a 1”- 1.5” maximum distance between the coverage or for 24/7 installation and technical support.
- Page 14 3/8” of self-leveling cement or manufacturer before powering up the latex-portland cement and allow proper WarmlyYours electric radiant heat system. manufacturer recommended cure time. Follow manufacturers recommended mixing directions carefully. 4. Perform 2nd ohm test.
- Page 15 Attach the mat to the subfloor using Using a hot glue gun, secure the cold Install a secondary waterproofing the TempZone™ Shower Mat to verify hot glue.Prepare the latex-modified lead to the mortar bed and over the membrane in accordance with the its dimensions and ensure it fits the thinset.
- Page 16 The electrical contractor must locate the point of break or short, in coordination If you have absolutely no reading (= infinity on your with the Technical Services Department of WarmlyYours. meter), and you are sure you adjusted the setting of the com.
- Page 17 This will help you and future owners of the home. The plan should indicate where the integrity of the Heating Element; following these simple WarmlyYours Heating Roll(s) is installed, the location of the control device and the rules can easily do this: amperage of the system.
-
Page 18: Warranty Information
Thank you for purchasing your new WarmlyYours TempZone™ floor warming system. To register your system, go online to www.WarmlyYours.com/warranty, or simply complete, detach and mail the Warranty Card within 30 days of date of purchase to: WarmlyYours, 590 Telser Rd Lake Zurich, IL 60047. For your convenience, you may also fax this card to (800) 408-1100. - Page 19 B U S I N E S S R E P LY M A I L FIRST-CLASS MAIL PERMIT NO 77 LONG GROVE IL POSTAGE WILL BE PAID BY ADDRESSEE WarmlyYours Inc 590 Telser Rd Ste B Lake Zurich, IL 60047...
Need help?
Do you have a question about the TempZone and is the answer not in the manual?
Questions and answers
I just had a bathroom floor heater installed. It worked for about 2 weeks and now the screen is blank. I can get a red light by pressing the test button but nothing else. I do not have an operator’s manual. What do I do?
If your WarmlyYours TempZone bathroom floor heater screen is blank after two weeks of use, follow these steps:
1. Check Power Supply – Verify that power is reaching the control or thermostat.
2. Inspect Circuit Capacity – Ensure the warming system does not exceed 80% of the circuit capacity.
3. Test Load Wires – Confirm that power is being delivered through the load wires.
4. Perform Resistance Tests – Conduct insulation and resistance tests to check for faults.
5. Look for Breaks or Shorts – If the system is not working, determine if there is a break or short in the wiring.
6. Contact WarmlyYours – If issues persist after verifying power and wiring, contact WarmlyYours for further troubleshooting or warranty support.
Avoid tampering with or attempting to repair the system yourself, as this may void the warranty.
This answer is automatically generated